Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P013A  O2 Sensor Slow Response - Rich to Lean Bank 1 Sensor 2  P013B  O2 Sensor Slow Response - Lean to Rich Bank 1 Sensor 2  


DESCRIPTION

Refer to DTC P0030.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>P0030

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P013A O2 Sensor Slow Response - Rich to Lean Bank 1 Sensor 2 The oxygen concentration rate of increase detected by the air fuel ratio sensor (for sensor 2) is equal to or greater than the standard value.
(3 trip detection logic)
·

Open or short in air fuel ratio sensor (for sensor 2) circuit

·

Air fuel ratio sensor (for sensor 2)

·

Exhaust system exhaust gas leak

·

ECM


Does not come on DTC stored
P013B O2 Sensor Slow Response - Lean to Rich Bank 1 Sensor 2 When switching from lean to rich, the difference in switching time between the air fuel ratio sensor (for sensor 2) and air fuel ratio sensor (for sensor 1) is equal to or greater than the standard value.
(3 trip detection logic)
·

Open or short in air fuel ratio sensor (for sensor 2) circuit

·

Air fuel ratio sensor (for sensor 2)

·

Exhaust system exhaust gas leak

·

ECM


Does not come on DTC stored

Related Data List
DTC No. Data List
P013A
P013B
·

O2 Sensor Lambda Bank 1 Sensor 1

·

O2 Sensor Lambda Bank 1 Sensor 2



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ECM and/or air fuel ratio sensor, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



Air fuel ratio sensors functional check


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine.


d.

Pre-check

HINT:
·

The air fuel ratio sensors can only emit a valid signal when at operating temperature and when the engine is running (after reaching the end of the dew point temperature). The air fuel ratio sensor upstream of the oxidation catalytic converter reaches operating readiness when the coolant temperature is between 70°C (158°F) and 80°C (176°F).

·

The air fuel ratio sensor downstream of the catalytic converter needs a few minutes more than the upstream air fuel ratio sensor to achieve operating readiness.

·

Even if the engine is already at operating temperature when it started, it still takes a few minutes for the air fuel ratio sensors to become operational.

·

If electrical faults are recorded for the air fuel ratio sensors, operating readiness is not granted and the functional check is prohibited. In this case, the electrical faults must be repaired first.



i.

Enter the following menus: Powertrain / Engine and ECT / Data List / Adaption state for Lambda Sensor 1 and Adaption state for Lambda Sensor 2.

Powertrain > Engine and ECT > Data List
Tester Display
Adaption state for Lambda Sensor 1
Adaption state for Lambda Sensor 2
50003 371 199,200

ii.

Read the values.

OK:

Greater than zero



iii.

Enter the following menus: Powertrain / Engine and ECT / Data List / Lambda Signal Valid State for Lambda Sensor 1 and Lambda Signal Valid State for Lambda Sensor 2.

Powertrain > Engine and ECT > Data List
Tester Display
Lambda Signal Valid State for Lambda Sensor 1
Lambda Signal Valid State for Lambda Sensor 2
50003 371 201,202

iv.

Read the values.

OK:

Greater than zero




e.

Plausibility check

HINT:

The following criteria are important for checking the plausibility of air-fuel ratios:

·

When in a steady state, the air-fuel ratios upstream and downstream of the oxidation catalytic converter are virtually identical.

·

The air-fuel ratios fluctuate within the ranges shown in the examples.

·

The signal from the air fuel ratio sensor downstream of the oxidation catalytic converter follows the signal from the upstream air fuel ratio sensor after a certain time delay (approximately 1 second).

·

Erratic changes to the air-fuel ratio are signaled virtually immediately by the air fuel ratio sensors. Heavy fouling of the upstream air fuel ratio sensor can mean that its signals are delayed by up to two seconds. In this situation, the signal from the air fuel ratio sensor upstream of the oxidation catalytic converter is sent after the signal from the downstream air fuel ratio sensor.



i.

Enter the following menus: Powertrain / Engine and ECT / Data List / O2 Sensor Lambda Bank 1 Sensor 1 and O2 Sensor Lambda Bank 1 Sensor 2.

Powertrain > Engine and ECT > Data List
Tester Display
O2 Sensor Lambda Bank 1 Sensor 1
O2 Sensor Lambda Bank 1 Sensor 2
50003 371 193,194

ii.

Read the values while the engine is idling.

Standard value:

Idling (warm up the engine): 1.5 to 8


HINT:

The following conditions for normal functioning affect the air-fuel ratios:

·

When exhaust-gas recirculation is active, the proportion of fresh air during combustion is lower, leading to a lower air-fuel ratio.

·

When the auxiliary function is operated, fuel consumption increases during combustion, leading to a lower air-fuel ratio.

·

The following illustration shows how conditions for normal functioning can affect the air-fuel ratios when idling.


A351152C01
2.427,1.573 2.833,1.573 2.833,1.573 3.146,1.417 true 3.333,1.573 3.479,1.396 3.479,1.396 3.615,1.396 true 2.427,4.302 2.844,4.302 2.844,4.302 3.052,4.146 true 3.208,4.344 3.417,4.135 3.417,4.135 3.604,4.135 true 0.906,0.156 1.24,0.354 0.333,0.198 10 false *a 1.01,3.135 1.323,3.292 0.313,0.156 10 false *b 2.26,4.208 2.573,4.365 0.313,0.156 10 false *c 3.615,4.042 3.927,4.198 0.313,0.156 10 false *d 2.146,3.302 2.458,3.458 0.313,0.156 10 false *e 3.24,3.302 3.552,3.458 0.313,0.156 10 false *f 4.542,3.281 4.844,3.51 0.302,0.229 10 false *g 5.792,1.042 6.135,1.25 0.344,0.208 10 false *h 5.833,1.813 6.177,2.01 0.344,0.198 10 false *i 1.469,0.344 1.802,0.573 0.333,0.229 10 false *j 5.833,5.094 6.146,5.25 0.313,0.156 10 false *k 5.823,2.458 6.135,2.615 0.313,0.156 10 false *k 5.844,4.469 6.188,4.667 0.344,0.198 10 false *i 5.813,3.771 6.156,3.979 0.344,0.208 10 false *h 2.146,0.396 2.458,0.552 0.313,0.156 10 false *e 3.24,0.385 3.552,0.542 0.313,0.156 10 false *f 4.542,0.375 4.844,0.604 0.302,0.229 10 false *g 2.26,1.479 2.573,1.635 0.313,0.156 10 false *c 3.635,1.313 3.948,1.469 0.313,0.156 10 false *d 1.479,3.24 1.813,3.469 0.333,0.229 10 false *j
*a Air-fuel ratios when exhaust-gas recirculation active *b Air-fuel ratios when exhaust-gas recirculation off
*c Signal from air fuel ratio sensor upstream of oxidation catalytic converter *d Signal from air fuel ratio sensor downstream of oxidation catalytic converter
*e No auxiliary functions activated *f Successive activation of auxiliary functions
*g Auxiliary function activated *h Air-fuel ratios level during idling with no auxiliary functions activated
*i Air-fuel ratios level during idling with auxiliary functions activated *j Air-fuel ratio
*k Second - -




iii.

Fully depress the accelerator pedal, and then measure the values after releasing the pedal.

Standard value:

1 to 32


HINT:

The air-fuel ratios behave as follows when the accelerator is pressed:

1.

Operating the accelerator pedal assembly: The engine acceleration and corresponding increase in fuel quantity lowers the air-fuel ratios.

2.

Keeping the accelerator pedal assembly pressed: Keeping the accelerator pedal assembly pressed (engine runs at maximum speed) stabilizes the air-fuel ratios a level considerably higher than the idling level.

3.

Releasing the accelerator pedal assembly: The fuel injection is switched off until the engine returns to idling speed. During this phase, the air-fuel ratios increase to a maximum value of 32.7 until the idling speed is reached and fuel injection is resumed.


·

The following illustration shows how the air-fuel ratios can behave when the accelerator is pressed.

·

When exhaust-gas recirculation is turned off, the air-fuel ratios during the idling phase will be somewhat higher than those shown in this example.

A351153C01
4.135,1.052 4.417,0.906 4.417,0.906 4.552,0.906 true 4.052,1.417 4.594,1.188 4.594,1.188 4.75,1.188 true 3.844,3.167 4.219,2.948 4.219,2.948 4.354,2.948 true 3.406,4.906 3.604,4.708 3.604,4.708 3.74,4.708 true 3.75,4.615 4.063,4.771 0.313,0.156 10 false *a 4.365,2.875 4.635,3.052 0.271,0.177 10 false *b 4.76,1.104 5.073,1.26 0.313,0.156 10 false *c 4.563,0.833 4.875,0.99 0.313,0.156 10 false *d 5.875,0.604 6.188,0.76 0.313,0.156 10 false *e 5.896,1.479 6.208,1.635 0.313,0.156 10 false *f 5.885,1.635 6.177,1.854 0.292,0.219 10 false *g 1.448,0.26 1.76,0.417 0.313,0.156 10 false *h 1.479,2.333 1.792,2.49 0.313,0.156 10 false *i 1.49,4.073 1.729,4.281 0.24,0.208 10 false *j 5.458,2.01 5.771,2.167 0.313,0.156 10 false *k 5.458,3.781 5.771,3.938 0.313,0.156 10 false *k 5.479,5.521 5.792,5.677 0.313,0.156 10 false *k
*a Accelerator pedal assembly signal *b Engine speed
*c Signal from air fuel ratio sensor upstream of oxidation catalytic converter *d Signal from air fuel ratio sensor downstream of oxidation catalytic converter
*e Air-fuel ratios level during overrun fuel cut-off *f Air-fuel ratios level at maximum speed
*g Air-fuel ratios level immediately after complete operation of accelerator pedal assembly *h Air-fuel ratio
*i rpm *j %
*k Second - -







PROCEDURE

1.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR (FOR SENSOR 2) - ECM)
a.

Disconnect the air fuel ratio sensor (for sensor 2) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B133-1 (AF2+) - B112-130 (AF2+) Always Below 1 Ω
B133-2 (AF2-) - B112-133 (AF2-) Always Below 1 Ω
B133-3 (HAF2) - B112-17 (HAF2) Always Below 1 Ω
B133-5 (TR2) - B112-131 (TR2) Always Below 1 Ω
B133-6 (RE2) - B112-134 (RE2) Always Below 1 Ω
B133-1 (AF2+) or B112-130 (AF2+) - Body ground Always 10 kΩ or higher
B133-2 (AF2-) or B112-133 (AF2-) - Body ground Always 10 kΩ or higher
B133-3 (HAF2) or B112-17 (HAF2) - Body ground Always 10 kΩ or higher
B133-5 (TR2) or B112-131 (TR2) - Body ground Always 10 kΩ or higher
B133-6 (RE2) or B112-134 (RE2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK EXHAUST SYSTEM

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.CHECK EXHAUST SYSTEM
a.

Check for exhaust gas leaks from the installation area of the air fuel ratio sensor (for sensor 2).

OK:

No exhaust gas leak.



Result:
Proceed to
OK
NG



OK

3.CHECK AIR FUEL RATIO SENSOR (FOR SENSOR 2)

NG

6.REPAIR OR REPLACE EXHAUST SYSTEM
3.CHECK AIR FUEL RATIO SENSOR (FOR SENSOR 2)
a.

Check the air fuel ratio sensor for tightness and damages.

OK:

No damage.



b.

Check for soot deposits in the air fuel ratio sensor (for sensor 2).

OK:

No soot deposits.



Result:
Proceed to
OK
NG



OK

4.REPLACE AIR FUEL RATIO SENSOR (FOR SENSOR 2)

NG

5.REPAIR OR REPLACE AIR FUEL RATIO SENSOR (FOR SENSOR 2)
4.REPLACE AIR FUEL RATIO SENSOR (FOR SENSOR 2)
a.

Replace the air fuel ratio sensor (for sensor 2).

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>AIR FUEL RATIO SENSOR(for Sensor 2)>REMOVAL


b.

Perform the O2 sensor learning value reset.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPAIR OR REPLACE AIR FUEL RATIO SENSOR (FOR SENSOR 2)
a.

Repair or replace the air fuel ratio sensor (for sensor 2).

i.

Apply compressed air to remove soot stuck to the air fuel ratio sensor. If soot cannot be removed, replace the air fuel ratio sensor.

HINT:

When the air fuel ratio sensor is replaced, perform initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>INITIALIZATION




Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE EXHAUST SYSTEM
a.

Repair or replace the exhaust system.

i.

Repair the area where leaks were found or replace parts.



Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END