Refer to DTC P0030.
Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>P0030
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P014C | O2 Sensor Slow Response - Rich to Lean Bank 1 Sensor 1 | The amount of time for the oxygen concentration rate of increase detected by the air fuel ratio sensor (for sensor 1) to reach the specified value is equal to or greater than the standard value.
(3 trip detection logic) |
·
Open or short in air fuel ratio sensor (for sensor 1) circuit ·
Air fuel ratio sensor (for sensor 1) ·
Exhaust system exhaust gas leak |
Does not come on | DTC stored |
| P014D | O2 Sensor Slow Response - Lean to Rich Bank 1 Sensor 1 | When switching from lean to rich, the difference in switching time between the air fuel ratio sensor (for sensor 1) and air fuel ratio sensor (for sensor 2) is equal to or greater than the standard value.
(3 trip detection logic) |
·
Open or short in air fuel ratio sensor (for sensor 1) circuit ·
Air fuel ratio sensor (for sensor 1) ·
Exhaust system exhaust gas leak |
Does not come on | DTC stored |
| DTC No. | Data List |
|---|---|
| P014C
P014D |
·
O2 Sensor Lambda Bank 1 Sensor 1 ·
O2 Sensor Lambda Bank 1 Sensor 2 |
Refer to DTC P0030.
Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>P0030
When replacing the ECM and/or air fuel ratio sensor, the ECM needs registration and initialization.
Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Air fuel ratio sensors functional check
Refer to DTC P013A.
Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>P013A
Disconnect the air fuel ratio sensor (for sensor 1) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B107-1 (AF1+) - B112-127 (AF1+) | Always | Below 1 Ω |
| B107-2 (AF1-) - B112-126 (AF1-) | Always | Below 1 Ω |
| B107-3 (HAF1) - B112-46 (HAF1) | Always | Below 1 Ω |
| B107-5 (TR1) - B112-128 (TR1) | Always | Below 1 Ω |
| B107-6 (RE1) - B112-125 (RE1) | Always | Below 1 Ω |
| B107-1 (AF1+) or B112-127 (AF1+) - Body ground | Always | 10 kΩ or higher |
| B107-2 (AF1-) or B112-126 (AF1-) - Body ground | Always | 10 kΩ or higher |
| B107-3 (HAF1) or B112-46 (HAF1) - Body ground | Always | 10 kΩ or higher |
| B107-5 (TR1) or B112-128 (TR1) - Body ground | Always | 10 kΩ or higher |
| B107-6 (RE1) or B112-125 (RE1) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for exhaust gas leaks from the installation area of the air fuel ratio sensor (for sensor 1).
No exhaust gas leak.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the air fuel ratio sensor (for sensor 1) for tightness and damages.
No damage.
Check for soot deposits in the air fuel ratio sensor (for sensor 1).
No soot deposits.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the air fuel ratio sensor (for sensor 1).
Click hereEngine / Hybrid System>2WW ENGINE CONTROL>AIR FUEL RATIO SENSOR(for Sensor 1)>REMOVAL
Perform the O2 sensor learning value reset.
Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the air fuel ratio sensor (for sensor 1).
Apply compressed air to remove soot stuck to the air fuel ratio sensor. If soot cannot be removed, replace the air fuel ratio sensor.
When the air fuel ratio sensor is replaced, perform initialization.
Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the exhaust system.
Repair the area where leaks were found or replace parts.
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for 60 seconds or more [A].
Perform road test [B].
Repeat [A] and [B] for the number of trips detected.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT