Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P0192  Fuel Rail Pressure Sensor "A" Circuit Low  P0193  Fuel Rail Pressure Sensor "A" Circuit High  


DESCRIPTION

The ECM monitors the internal fuel pressure of the common rail using the fuel pressure sensor, and controls the fuel quantity control valve to regulate the internal pressure to the target pressure. The pressure sensor is a semiconductor that varies electrical resistance when pressure is applied to its silicon chip.

This sensor outputs the voltage in proportion to the internal fuel pressure.

The measuring range of approx. 0.5 to 4.5 volts corresponds to a rail pressure of between 0 kPa (0 bar) and 180 MPa (1800 bar).

A342524E01
1.042,1.74 1.208,1.063 1.208,1.063 1.458,1.063 false 1.521,0.99 2.979,1.25 1.458,0.26 10 false Fuel Pressure Sensor 3.781,0.448 5.552,0.688 1.771,0.24 10 false Property of Output Voltage: 4.146,0.823 5.917,1.063 1.771,0.24 10 false Fuel Pressure Voltage (V): 4.063,1.417 4.427,1.635 0.365,0.219 10 false 4.5 4.063,2.313 4.427,2.531 0.365,0.219 10 false 0.5 4.729,2.74 4.99,2.958 0.26,0.219 10 false 0 6.156,2.729 6.458,2.979 0.302,0.25 10 false 180 5.469,3.073 6.781,3.313 1.313,0.24 10 false Fuel Pressure (MPa)

For information on the fuel system, refer to System Description.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>SYSTEM DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0192 Fuel Rail Pressure Sensor "A" Circuit Low Fuel pressure sensor output voltage 0.131 V or less for 0.14 seconds.
(1 trip detection logic)
·

Open or short in fuel pressure sensor circuit

·

Fuel pressure sensor

·

ECM


Comes on DTC stored
P0193 Fuel Rail Pressure Sensor "A" Circuit High Fuel pressure sensor output voltage 3.29 V or more for 0.14 seconds.
(1 trip detection logic)
·

Open or short in fuel pressure sensor circuit

·

Fuel pressure sensor

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0192
P0193
·

Target Common Rail Pressure

·

Common Rail Pressure



WIRING DIAGRAM

A165731E73
0.583,2.042 1.01,2.229 0.427,0.188 10 false B124 0.583,2.208 2.104,2.5 1.521,0.292 10 false Fuel Pressure Sensor 6.052,2.042 6.5,2.271 0.448,0.229 10 false B112 6.063,2.198 6.49,2.375 0.427,0.177 10 false ECM 1.542,1.583 1.792,1.792 0.25,0.208 10 false E1 1.354,1.031 1.781,1.24 0.427,0.208 10 false PCR1 1.427,0.469 1.75,0.667 0.323,0.198 10 false VC1 5.698,1.583 6.063,1.781 0.365,0.198 10 false E2S 5.698,1.052 5.99,1.25 0.292,0.198 10 false PC 5.688,0.469 6.094,0.688 0.406,0.219 10 false VCS 1.844,0.354 2.01,0.573 0.167,0.219 10 false 3 1.844,0.927 1.969,1.104 0.125,0.177 10 false 2 1.844,1.479 1.969,1.656 0.125,0.177 10 false 1 5.385,0.365 5.594,0.552 0.208,0.188 10 false 54 5.323,0.938 5.583,1.115 0.26,0.177 10 false 101 5.323,1.469 5.594,1.646 0.271,0.177 10 false 102

CAUTION / NOTICE / HINT

NOTICE:

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION


HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (COMMON RAIL PRESSURE AND TARGET COMMON RAIL PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Target Common Rail Pressure and Common Rail Pressure.

Powertrain > Engine and ECT > Data List
Tester Display
Target Common Rail Pressure
Common Rail Pressure
50003 371 50,51

d.

Check that the internal fuel pressure of the common rail is within the specification below.

OK:

Common Rail Pressure is within 10000 kPa of Target Common Rail Pressure when the engine is idling and running at 3000 rpm without load.



Result:
Proceed to
OK
NG



OK

2.CHECK WHETHER DTC OUTPUT RECURS (DTC P0192, P0193)

NG

3.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)
2.CHECK WHETHER DTC OUTPUT RECURS (DTC P0192, P0193)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Read the DTCs.


Result:
Result Proceed to
No DTC output A
DTC P0192 or P0193 B



A

B

7.REPLACE ECM
3.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)
a.

Disconnect the fuel pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B124-2 (PCR1) - B112-101 (PC) Always Below 1 Ω
B124-3 (VC1) - B112-54 (VCS) Always Below 1 Ω
B124-1 (E1) - B112-102 (E2S) Always Below 1 Ω
B124-2 (PCR1) or B112-101 (PC) - Body ground Always 10 kΩ or higher
B124-3 (VC1) or B112-54 (VCS) - Body ground Always 10 kΩ or higher
B124-1 (E1) or B112-102 (E2S) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (VC VOLTAGE)

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CHECK HARNESS AND CONNECTOR (VC VOLTAGE)
A351160C08
0.24,1.094 0.656,1.354 0.417,0.26 1.083,1.771 1.365,1.281 true 2.396,1.771 2.052,1.281 true 0.271,0.135 0.583,0.333 0.313,0.198 10 false *a 0.979,1.802 1.292,2 0.313,0.198 10 false E1 2.292,1.802 2.604,2 0.313,0.198 10 false VC1 0.281,1.146 0.677,1.344 0.396,0.198 10 false B124
*a Front view of wire harness connector
(to Fuel Pressure Sensor)


a.

Disconnect the fuel pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B124-3 (VC1) - B124-1 (E1) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

5.REPLACE FUEL PRESSURE SENSOR

NG

7.REPLACE ECM
5.REPLACE FUEL PRESSURE SENSOR
a.

Replace the fuel pressure sensor.

Click hereEngine / Hybrid System>2WW FUEL>FUEL PRESSURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0192, P0193)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0192, P0193)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Read the DTCs.


Result:
Result Proceed to
DTC P0192 or P0193 A
No DTC output B



A

7.REPLACE ECM

B

END

7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END