Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P0237  Turbo / Super Charger Boost Sensor "A" Circuit Low  P0238  Turbocharger / Supercharger Boost Sensor "A" Circuit High  


DESCRIPTION

Refer to DTC P0236.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>P0236

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0237 Turbo / Super Charger Boost Sensor "A" Circuit Low Turbo pressure sensor assembly output voltage is 0.152 V or less for 0.1 seconds.
(3 trip detection logic)
·

Open or short in turbo pressure sensor assembly circuit

·

Turbo pressure sensor assembly

·

ECM


Comes on DTC stored
P0238 Turbocharger / Supercharger Boost Sensor "A" Circuit High Turbo pressure sensor assembly output voltage is 4.75 V or higher for 0.1 seconds.
(3 trip detection logic)
·

Open or short in turbo pressure sensor assembly circuit

·

Turbo pressure sensor assembly

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0237
P0238
·

MAP

·

Atmosphere Pressure



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

After replacing the turbo pressure sensor assembly, the ECM needs initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION



HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (MAP AND ATMOSPHERE PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAP and Atmosphere Pressure.

Powertrain > Engine and ECT > Data List
Tester Display
Atmosphere Pressure
MAP
50003 371 5,3

d.

Compare the values when the ignition switch is ON.

Standard:

Difference between the MAP and the Atmosphere Pressure is less than 7 kPa.


HINT:

Standard atmospheric pressure is 101 kPa. For every 100 m increase in altitude, pressure drops by 1 kPa.

Varies by weather.



Result:
Proceed to
OK
NG



OK

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

2.CHECK HARNESS AND CONNECTOR (TURBO PRESSURE SENSOR ASSEMBLY - ECM)
2.CHECK HARNESS AND CONNECTOR (TURBO PRESSURE SENSOR ASSEMBLY - ECM)
a.

Disconnect the turbo pressure sensor assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B122-3 (PIM) - B112-111 (PIM) Always Below 1 Ω
B122-1 (VC) - B112-61 (VPIM) Always Below 1 Ω
B122-2 (E) - B112-76 (EPIM) Always Below 1 Ω
B122-3 (PIM) or B112-111 (PIM) - Body ground Always 10 kΩ or higher
B122-1 (VC) or B112-61 (VPIM) - Body ground Always 10 kΩ or higher
B122-2 (E) or B112-76 (EPIM) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (VC VOLTAGE)

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK HARNESS AND CONNECTOR (VC VOLTAGE)
A351158C20
0.302,1.146 0.75,1.365 0.448,0.219 0.948,1.792 1.354,1.281 true 2.094,1.833 1.74,1.323 true 0.188,0.177 0.5,0.333 0.313,0.156 10 false *a 0.365,1.177 0.833,1.375 0.469,0.198 10 false B122 0.802,1.833 1.271,2.031 0.469,0.198 10 false VC 2.083,1.854 2.552,2.052 0.469,0.198 10 false E
*a Front view of wire harness connector
(to Turbo Pressure Sensor Assembly)


a.

Disconnect the turbo pressure sensor assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B122-1 (VC) - B122-2 (E) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

4.REPLACE TURBO PRESSURE SENSOR ASSEMBLY

NG

6.REPLACE ECM
4.REPLACE TURBO PRESSURE SENSOR ASSEMBLY
a.

Replace the turbo pressure sensor assembly.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>MANIFOLD ABSOLUTE PRESSURE SENSOR>REMOVAL


b.

Perform the upstream turbine pressure learning value reset.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS
5.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Read the DTCs.

Result:
Result Proceed to
DTC P0237 or P0238 A
No DTC output B




A

6.REPLACE ECM

B

END

6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END