Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P0401  Exhaust Gas Recirculation "A" Flow Insufficient Detected  


DESCRIPTION

The exhaust gas recirculation is a measure to reduce the formation of nitrogen oxides (NOx). Nitrogen oxides are produced in large quantities when combustion occurs with excess air and at a very high temperature. The oxygen and nitrogen of the combustion air combine to form nitric oxide (NO) and nitrogen dioxide (NO2). The EGR is the diesel engine isolated at idle and always needed in the partial load range, because it is working with a very large excess of air.

Mixing the recirculated exhaust gas with fresh air renders it inert, decreasing the amount of oxygen and nitrogen inside the cylinder and lowering the combustion temperature to a maximum of 500°C (932°F).

The recirculated exhaust gas is cooled by the EGR cooler to further increase this effect.

The amount of averaging used for more accurate adaptation of the exhaust gas recirculation to tolerances of the injection amounts.

An average overall cylinder injection quantity is determined from the measured value by the air fuel ratio sensor and that measured by the mass air flow meter sub-assembly. This value is compared to the injection quantity predetermined by the ECM. If a deviation is detected, the air mass is corrected by adjusting the EGR actuator to the actual injection quantity to set the correct air fuel ratio value. The amount of average adaptation is not a quick scheme but an adaptive learning process. This means that the injection quantity error is taught in an adaptive map which is stored in the ECM permanently.

HINT:

For more information on the EGR control, refer to System Description.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>SYSTEM DESCRIPTION


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0401 Exhaust Gas Recirculation "A" Flow Insufficient Detected During normal operation, EGR negative deviation falls below limit value, or EGR rate exceeds limit value for 7.5 seconds.
(3 trip detection logic)
·

Intake system air leak

·

Exhaust system exhaust gas leak

·

Diesel throttle body assembly

·

EGR valve assembly

·

Turbocharger sub-assembly

·

EGR cooler assembly

·

ECM


Comes on DTC stored

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

After replacing the EGR valve assembly, the ECM needs initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

After replacing the mass air flow meter sub-assembly, the ECM needs initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION



HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK INTAKE SYSTEM
a.

Check for air leaks in the intake system after the turbocharger sub-assembly.

OK:

No leakage.



Result:
Proceed to
OK
NG



OK

2.CHECK MASS AIR FLOW METER SUB-ASSEMBLY

NG

15.REPAIR OR REPLACE INTAKE SYSTEM
2.CHECK MASS AIR FLOW METER SUB-ASSEMBLY
a.

Check for DTCs related to the validity of the mass air flow meter sub-assembly.


Result:
Proceed to
OK
NG



OK

4.CHECK DIESEL THROTTLE BODY ASSEMBLY

NG

3.CHECK EXHAUST SYSTEM
3.CHECK EXHAUST SYSTEM
a.

Check for exhaust gas leaks in the exhaust system before the turbocharger sub-assembly.

OK:

No leakage.



Result:
Proceed to
OK
NG



OK

4.CHECK DIESEL THROTTLE BODY ASSEMBLY

NG

14.REPAIR OR REPLACE EXHAUST SYSTEM
4.CHECK DIESEL THROTTLE BODY ASSEMBLY
a.

Check for DTCs related to the diesel throttle body assembly.

OK:

DTCs related to the diesel throttle body assembly are not output.



Result:
Proceed to
OK
NG



OK

5.CHECK EGR VALVE ASSEMBLY

NG

13.REPAIR OR REPLACE DIESEL THROTTLE BODY ASSEMBLY
5.CHECK EGR VALVE ASSEMBLY
a.

Check for DTCs related to the EGR valve assembly.

OK:

DTCs related to the EGR valve assembly are not output.



Result:
Proceed to
OK
NG



OK

6.CHECK TURBOCHARGER SUB-ASSEMBLY

NG

12.REPAIR OR REPLACE EGR VALVE ASSEMBLY
6.CHECK TURBOCHARGER SUB-ASSEMBLY
a.

Check for DTCs related to the turbocharger sub-assembly.

OK:

DTCs related to the turbocharger sub-assembly are not output.



Result:
Proceed to
OK
NG



OK

7.CHECK EGR COOLER ASSEMBLY

NG

11.REPAIR OR REPLACE TURBOCHARGER SUB-ASSEMBLY
7.CHECK EGR COOLER ASSEMBLY
a.

Check that the airflow is not slowed by soot deposits in the EGR cooler.

OK:

Airflow is not slowed by soot deposits.



Result:
Proceed to
OK
NG



OK

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0401)

NG

10.CLEAN OR REPLACE EGR COOLER ASSEMBLY
8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0401)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Read the DTCs.

Result:
Result Proceed to
No DTC output A
DTC P0401 B




A

END

B

9.REPLACE ECM
9.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.CLEAN OR REPLACE EGR COOLER ASSEMBLY
a.

Clean or replace the EGR cooler assembly.


Result:
Proceed to
NEXT



NEXT

16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPAIR OR REPLACE TURBOCHARGER SUB-ASSEMBLY
a.

Repair or replace turbocharger sub-assembly or perform inspections and troubleshooting for related DTCs.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>DIAGNOSTIC TROUBLE CODE CHART


Result:
Proceed to
NEXT



NEXT

16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.REPAIR OR REPLACE EGR VALVE ASSEMBLY
a.

Repair or replace EGR valve assembly or perform inspections and troubleshooting for related DTCs.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>DIAGNOSTIC TROUBLE CODE CHART

HINT:

When the EGR valve assembly is replaced, perform initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.REPAIR OR REPLACE DIESEL THROTTLE BODY ASSEMBLY
a.

Repair or replace diesel throttle body assembly or perform inspections and troubleshooting for related DTCs.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>DIAGNOSTIC TROUBLE CODE CHART


Result:
Proceed to
NEXT



NEXT

16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
14.REPAIR OR REPLACE EXHAUST SYSTEM
a.

Repair or replace the malfunctioning parts of the exhaust system.


Result:
Proceed to
NEXT



NEXT

16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
15.REPAIR OR REPLACE INTAKE SYSTEM
a.

Repair or replace the malfunctioning parts of the intake system.


Result:
Proceed to
NEXT



NEXT

16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END