Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P0500  Vehicle Speed Sensor "A"  


DESCRIPTION

The wheel speed sensor monitors the wheel rotation speed and sends a signal to the skid control ECU.

The skid control ECU converts the wheel speed signal into a 4-pulse signal and transmits it to the ECM via the combination meter. The ECM determines the vehicle speed based on the frequency of the pulse signal.

A115899E76
0.302,1.26 1.542,1.635 1.24,0.375 10 false From Wheel Speed Sensor 1.813,1.938 3.229,2.104 1.417,0.167 10 false Skid Control ECU 3.375,1.906 5.313,2.177 1.938,0.271 10 false Combination Meter Assembly 2.906,0.698 4.615,1.083 1.708,0.385 10 false 4-Pulse Signal 4.854,0.688 6.031,0.969 1.177,0.281 10 false 4-Pulse Signal 6.01,1.24 6.458,1.406 0.448,0.167 10 false ECM

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0500 Vehicle Speed Sensor "A" Vehicle speed signal is not input to ECM regardless of whether vehicle is in motion.
(1 or 2 trip detection logic)
·

Open or short in speedometer circuit

·

Combination meter assembly

·

ECM


Comes on / Does not come on*
*: Depending on the detection condition.
DTC stored

HINT:

For vehicles with a cruise control system, detection does not start unless the following conditions are met.

·

Adjustable Speed Limiter (ASL) Main button status is ON.

·

Average time period between speed pulses is a non-zero value and frozen for a calibrated time.

·

Sensed vehicle speed is greater than a calibrated threshold.

·

Engine is running.



Related Data List
DTC No. Data List
P0500 Vehicle Speed

WIRING DIAGRAM

A160610E34
0.281,1.823 2.167,2.031 1.885,0.208 10 false from Skid Control ECU 2.396,1.708 2.615,1.896 0.219,0.188 10 false SI 3.635,1.719 3.875,1.896 0.24,0.177 10 false +S 3.927,1.708 4.146,1.896 0.219,0.188 10 false 6 2.198,2.635 2.51,2.833 0.313,0.198 10 false G16 2.198,2.792 4.396,3.042 2.198,0.25 10 false Combination Meter Assembly 4.958,1.698 5.177,1.885 0.219,0.188 10 false 51 5.979,1.417 6.438,1.615 0.458,0.198 10 false 5 V 5.198,1.677 5.563,1.875 0.365,0.198 10 false SPD 5.708,2.635 6.167,2.833 0.458,0.198 10 false A62 5.708,2.792 6.167,2.99 0.458,0.198 10 false ECM 2.229,1.698 2.542,1.896 0.313,0.198 10 false 5

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK OPERATION OF SPEEDOMETER
a.

Drive the vehicle and check whether the operation of the speedometer in the combination meter is normal.

HINT:

The vehicle speed sensor is operating normally if the speedometer reading is normal.


OK:

The vehicle speed sensor is operating normally.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (VEHICLE SPEED)

NG

8.CHECK SPEEDOMETER CIRCUIT
2.READ VALUE USING GTS (VEHICLE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Vehicle Speed.

Powertrain > Engine and ECT > Data List
Tester Display
Vehicle Speed
50003 371 8

e.

Drive the vehicle.


f.

Read the value displayed on the GTS.

OK:

Vehicle speeds displayed on GTS and speedometer display are equal.



Result:
Proceed to
OK
NG



OK

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

3.CHECK HARNESS AND CONNECTOR (ECM OUTPUT VOLTAGE)
3.CHECK HARNESS AND CONNECTOR (ECM OUTPUT VOLTAGE)
a.
A127854C26
0.396,0.521 0.802,0.771 0.406,0.25 1.188,1.313 1.479,0.656 false 0.156,0.135 0.823,0.427 0.667,0.292 10 false *a 1.552,0.542 1.969,0.813 0.417,0.271 10 false +S 0.469,0.563 0.917,0.802 0.448,0.24 10 false G16
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G16-6 (+S) - Body ground Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

4.CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL WAVEFORM)

NG

6.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
4.CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL WAVEFORM)
A205820C25
0.156,0.792 0.563,1.052 0.406,0.26 2.104,1.104 2.531,1.938 false 0.167,0.167 0.396,0.396 0.229,0.229 10 false *a 0.229,0.844 0.552,1.073 0.323,0.229 10 false G16 2.458,1.969 3.042,2.188 0.583,0.219 10 false +S 2.917,3.573 3.427,3.823 0.51,0.25 10 false GND
*a Component with harness connected
(Combination Meter Assembly)


a.

Turn the ignition switch to ON.


b.

Move the shift lever to neutral.


c.

Jack up the vehicle.


d.

Check the voltage between the terminal of the combination meter and the body ground while a wheel is turned slowly.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G16-6 (+S) - Body ground Ignition switch ON Voltage generated intermittently


HINT:

The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.



Result:
Result Proceed to
OK A
NG B



A

7.REPLACE ECM

B

5.REPLACE COMBINATION METER ASSEMBLY
5.REPLACE COMBINATION METER ASSEMBLY
a.

Replace the combination meter assembly.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the combination meter assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-6 (+S) - A62-51 (SPD) Always Below 1 Ω
G16-6 (+S) or A62-51 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE ECM

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CHECK SPEEDOMETER CIRCUIT
a.

Check the speedometer circuit.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speed Signal Circuit

HINT:

Inspect the brake actuator assembly and speed sensor.



Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END