Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P0562  System Voltage Low  


DESCRIPTION

The battery supplies electricity to the ECM even when the ignition switch is off. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, the ECM memory is cleared and the ECM determines that there is a malfunction in the power supply circuit. When the engine is next started, the ECM illuminates the MIL and stores the DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0562 System Voltage Low When ECM supply voltage falls below 1.25 V for 5 seconds.
(1 trip detection logic)
·

ECM power supply circuit

·

ECM


Comes on DTC stored

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (BATTERY VOLTAGE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Battery Voltage.

Powertrain > Engine and ECT > Data List
Tester Display
Battery Voltage
50003 371 16

d.

Read the value.

OK:

11 to 14 V



Result:
Proceed to
OK
NG



OK

15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

2.CHECK HARNESS AND CONNECTOR
2.CHECK HARNESS AND CONNECTOR
a.

Disconnect the negative (-) battery terminal.


b.

Disconnect the positive (+) battery terminal.


c.

Disconnect the ECM connector.


d.

Remove the EFI MAIN NO. 1 relay from the engine room and junction block.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A62-4 (E1) - Body ground Always Below 1 Ω
A62-5 (E2) - Body ground Always Below 1 Ω
A62-17 (E3) - Body ground Always Below 1 Ω
A62-18 (E4) - Body ground Always Below 1 Ω
A62-15 (BATT) - positive (+) battery terminal Always Below 1 Ω
A62-2 (+B) - 3 (EFI MAIN NO. 1 relay holder) Always Below 1 Ω
A62-14 (+B2) - 3 (EFI MAIN NO. 1 relay holder) Always Below 1 Ω
A62-1 (+B3) - 3 (EFI MAIN NO. 1 relay holder) Always Below 1 Ω
A62-9 (MREL) - 1 (EFI MAIN NO. 1 relay holder) Always Below 1 Ω
5 (EFI MAIN NO. 1 relay holder) - positive (+) battery terminal Always Below 1 Ω
2 (EFI MAIN NO. 1 relay holder) - Body ground Always Below 1 Ω
A62-15 (BATT) or positive (+) battery terminal - Body ground Always 10 kΩ or higher
A62-2 (+B) or 3 (EFI MAIN NO. 1 relay holder) - Body ground Always 10 kΩ or higher
A62-14 (+B2) or 3 (EFI MAIN NO. 1 relay holder) - Body ground Always 10 kΩ or higher
A62-1 (+B3) or 3 (EFI MAIN NO. 1 relay holder) - Body ground Always 10 kΩ or higher
A62-9 (MREL) or 1 (EFI MAIN NO. 1 relay holder) - Body ground Always 10 kΩ or higher
5 (EFI MAIN NO. 1 relay holder) or positive (+) battery terminal - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (IGSW VOLTAGE)

NG

14.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK HARNESS AND CONNECTOR (IGSW VOLTAGE)
A325490C28
0.313,1 0.74,1.24 0.427,0.24 0.865,1.823 1.865,1.365 false 0.104,0.073 0.417,0.271 0.313,0.198 10 false *a 0.396,1.042 0.802,1.292 0.406,0.25 10 false A62 0.625,1.844 1.594,2.052 0.969,0.208 10 false IGSW
*a Front view of wire harness connector
(to ECM)


a.

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A62-37 (IGSW) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.INSPECT EFI MAIN NO. 1 RELAY

NG

8.INSPECT IG2 RELAY
4.INSPECT EFI MAIN NO. 1 RELAY
a.

Inspect the EFI MAIN NO. 1 relay.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0562)

NG

7.REPLACE EFI MAIN NO. 1 RELAY
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0562)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Read the DTCs.

Result:
Result Proceed to
No DTC output A
DTC P0562 B




A

END

B

6.REPLACE ECM
6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPLACE EFI MAIN NO. 1 RELAY
a.

Replace the EFI MAIN NO. 1 relay.


Result:
Proceed to
NEXT



NEXT

15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.INSPECT IG2 RELAY

Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR

NG

13.REPLACE IG2 RELAY
9.CHECK HARNESS AND CONNECTOR
a.

Disconnect the negative (-) battery terminal.


b.

Disconnect the positive (+) battery terminal.


c.

Disconnect the ECM connector.


d.

Remove the EFI MAIN NO. 1 relay from the engine room relay block and junction block.


e.

Remove the IG2 relay from the engine room relay block and junction block.


f.

Remove the certification ECU (smart key ECU assembly) (w/ Entry and Start System).


g.

Disconnect the ignition switch assembly connector (w/o Entry and Start System).


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A62-37 (IGSW) - 5 (IG2 relay holder) Always Below 1 Ω
3 (IG2 relay holder) - positive (+) battery terminal Always Below 1 Ω
2 (IG2 relay holder) - Body ground Always Below 1 Ω
1 (IG2 relay holder) - G4-3 (IG2) Always Below 1 Ω
1 (IG2 relay holder) - G82-9 (IG2D) Always Below 1 Ω
A62-37 (IGSW) or 5 (IG2 relay holder) - Body ground Always 10 kΩ or higher
3 (IG2 relay holder) or positive (+) battery terminal - Body ground Always 10 kΩ or higher
1 (IG2 relay holder) or G4-3 (IG2) - Body ground Always 10 kΩ or higher
1 (IG2 relay holder) or G82-9 (IG2D) - Body ground Always 10 kΩ or higher


Result:
Result Proceed to
OK (w/o Entry and Start System) A
OK (w/ Entry and Start System) B
NG C




A

10.INSPECT IGNITION SWITCH ASSEMBLY

B

12.CHECK ENTRY AND START SYSTEM

C

14.REPAIR OR REPLACE HARNESS OR CONNECTOR
10.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly.

Click hereEngine / Hybrid System>2WW STARTING>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

14.REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

11.REPLACE IGNITION SWITCH ASSEMBLY
11.REPLACE IGNITION SWITCH ASSEMBLY
a.

Replace the ignition switch assembly.

Click hereEngine / Hybrid System>2WW STARTING>IGNITION SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.CHECK ENTRY AND START SYSTEM

NEXT

15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.REPLACE IG2 RELAY
a.

Replace the IG2 relay.


Result:
Proceed to
NEXT



NEXT

15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
14.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END