Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P0563  System Voltage High  


DESCRIPTION

Refer to DTC P0562.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>P0562

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0563 System Voltage High When ECM supply voltage exceeds upper limit (supply voltage + 3.1 V) for 0.5 seconds.
(1 trip detection logic)
·

Charging system

·

Battery (If 24 V battery is installed)

·

ECM


Comes on DTC stored

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (BATTERY VOLTAGE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Battery Voltage.

Powertrain > Engine and ECT > Data List
Tester Display
Battery Voltage
50003 371 16

d.

Read the value.

OK:

11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK FOR EXCESSIVELY LARGE VOLTAGE

NG

3.CHECK HARNESS AND CONNECTOR
2.CHECK FOR EXCESSIVELY LARGE VOLTAGE
a.

Check that an excessively large voltage was not applied in the past.

HINT:

When using a battery charger, if the charger is incorrectly set, DTCs will be cleared when the engine is started due to an excessively large voltage being applied.



Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
3.CHECK HARNESS AND CONNECTOR
a.

Disconnect the negative (-) battery terminal.


b.

Disconnect the positive (+) battery terminal.


c.

Disconnect the ECM connector.


d.

Remove the EFI MAIN NO. 1 relay from the engine room relay block and junction block.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A62-4 (E1) - Body ground Always Below 1 Ω
A62-5 (E2) - Body ground Always Below 1 Ω
A62-17 (E3) - Body ground Always Below 1 Ω
A62-18 (E4) - Body ground Always Below 1 Ω
A62-15 (BATT) - positive (+) battery terminal Always Below 1 Ω
A62-2 (+B) - 3 (EFI MAIN NO. 1 relay holder) Always Below 1 Ω
A62-14 (+B2) - 3 (EFI MAIN NO. 1 relay holder) Always Below 1 Ω
A62-1 (+B3) - 3 (EFI MAIN NO. 1 relay holder) Always Below 1 Ω
A62-9 (MREL) - 1 (EFI MAIN NO. 1 relay holder) Always Below 1 Ω
5 (EFI MAIN NO. 1 relay holder) - positive (+) battery terminal Always Below 1 Ω
2 (EFI MAIN NO. 1 relay holder) - Body ground Always Below 1 Ω
A62-9 (MREL) - A62-2 (+B) Always 10 kΩ or higher
A62-9 (MREL) - A62-14 (+B2) Always 10 kΩ or higher
A62-9 (MREL) - A62-1 (+B3) Always 10 kΩ or higher
A62-15 (BATT) or positive (+) battery terminal - Body ground Always 10 kΩ or higher
A62-2 (+B) or 3 (EFI MAIN NO. 1 relay holder) - Body ground Always 10 kΩ or higher
A62-14 (+B2) or 3 (EFI MAIN NO. 1 relay holder) - Body ground Always 10 kΩ or higher
A62-1 (+B3) or 3 (EFI MAIN NO. 1 relay holder) - Body ground Always 10 kΩ or higher
A62-9 (MREL) or 1 (EFI MAIN NO. 1 relay holder) - Body ground Always 10 kΩ or higher
5 (EFI MAIN NO. 1 relay holder) or positive (+) battery terminal - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK CHARGING SYSTEM

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CHECK CHARGING SYSTEM
a.

Check the charging system.

Click herePower Source / Network>2WW BATTERY / CHARGING>CHARGING SYSTEM>ON-VEHICLE INSPECTION

HINT:

Check that the generated voltage is not too high.



Result:
Proceed to
OK
NG



OK

5.REPLACE ECM

NG

6.REPAIR OR REPLACE CHARGING SYSTEM
5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE CHARGING SYSTEM
a.

Repair or replace the charging system.


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END