Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P066B  Cylinder 1 Glow Plug Control Circuit High  P066D  Cylinder 2 Glow Plug Control Circuit High  P066F  Cylinder 3 Glow Plug Control Circuit High  P0671  Cylinder 1 Glow Plug Circuit/Open  P0672  Cylinder 2 Glow Plug Circuit/Open  P0673  Cylinder 3 Glow Plug Circuit/Open  P0674  Cylinder 4 Glow Plug Circuit/Open  P067B  Cylinder 4 Glow Plug Control Circuit High  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P066B Cylinder 1 Glow Plug Control Circuit High When system determines short in No. 1 glow plug system from glow plug controller assembly via LIN communication for 1.2 seconds or more.
(3 trip detection logic)
·

Glow plug controller assembly

·

No. 1 glow plug

·

Short in No. 1 glow plug circuit


Does not come on DTC stored
P066D Cylinder 2 Glow Plug Control Circuit High When system determines short in No. 2 glow system from glow plug controller assembly via LIN communication for 1.2 seconds or more.
(3 trip detection logic)
·

Glow plug controller assembly

·

No. 2 glow plug

·

Short in No. 2 glow plug circuit


Does not come on DTC stored
P066F Cylinder 3 Glow Plug Control Circuit High When system determines short in No. 3 glow plug system from glow plug controller assembly via LIN communication for 1.2 seconds or more.
(3 trip detection logic)
·

Glow plug controller assembly

·

No. 3 glow plug

·

Short in No. 3 glow plug circuit


Does not come on DTC stored
P0671 Cylinder 1 Glow Plug Circuit/Open When system determines short in No. 4 glow plug system from glow plug controller assembly via LIN communication for 1.2 seconds or more.
(3 trip detection logic)
·

Glow plug controller assembly

·

No. 4 glow plug

·

Short in No. 4 glow plug circuit


Does not come on DTC stored
P0672 Cylinder 2 Glow Plug Circuit/Open When system determines open in No. 1 glow plug system from glow plug controller assembly via LIN communication for 1.2 seconds or more.
(3 trip detection logic)
·

Glow plug controller assembly

·

No. 1 glow plug

·

Open in No. 1 glow plug circuit


Does not come on DTC stored
P0673 Cylinder 3 Glow Plug Circuit/Open When system determines open in No. 2 glow plug system from glow plug controller assembly via LIN communication for 1.2 seconds or more.
(3 trip detection logic)
·

Glow plug controller assembly

·

No. 2 glow plug

·

Open in No. 2 glow plug circuit


Does not come on DTC stored
P0674 Cylinder 4 Glow Plug Circuit/Open When system determines open in No. 3 glow plug system from glow plug controller assembly via LIN communication for 1.2 seconds or more.
(3 trip detection logic)
·

Glow plug controller assembly

·

No. 3 glow plug

·

Open in No. 3 glow plug circuit


Does not come on DTC stored
P067B Cylinder 4 Glow Plug Control Circuit High When system determines open in No. 4 glow plug system from glow plug controller assembly via LIN communication for 1.2 seconds or more.
(3 trip detection logic)
·

Glow plug controller assembly

·

No. 4 glow plug

·

Open in No. 4 glow plug circuit


Does not come on DTC stored

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

d.

Read the DTCs.

Result:
Result Proceed to
P0671, P0672, P0673 and/or P0674 is output A
P066B, P066D, P066F and/or P067B is output B




A

2.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER ASSEMBLY - GLOW PLUG)

B

3.CHECK HARNESS AND CONNECTOR
2.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER ASSEMBLY - GLOW PLUG)
a.

Disconnect connectors of the glow plug controller assembly.


b.

Remove the glow plug connector from the glow plug.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B121-4 (GL1) - k2-1 (GLW1) Always Below 1 Ω
B121-1 (GL2) - k3-1 (GLW2) Always Below 1 Ω
B121-6 (GL3) - k4-1 (GLW3) Always Below 1 Ω
B121-5 (GL4) - k5-1 (GLW4) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.REPLACE GLOW PLUG

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK HARNESS AND CONNECTOR
a.

Disconnect connectors of the glow plug controller assembly.


b.

Remove the glow plug connector from the glow plug.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B121-4 (GL1) or k2-1 (GLW1) - Body ground Always Below 1 Ω
B121-1 (GL2) or k3-1 (GLW2) - Body ground Always Below 1 Ω
B121-6 (GL3) or k4-1 (GLW3) - Body ground Always Below 1 Ω
B121-5 (GL4) or k5-1 (GLW4) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.REPLACE GLOW PLUG

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE GLOW PLUG
a.

Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
OK
NG



OK

END

NG

6.REPLACE GLOW PLUG CONTROLLER ASSEMBLY
6.REPLACE GLOW PLUG CONTROLLER ASSEMBLY
a.

Replace the glow plug controller assembly.

Click hereEngine / Hybrid System>2WW STARTING>GLOW PLUG CONTROLLER>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END