Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P0704  Clutch Switch Input Circuit  


DESCRIPTION

The clutch switch is mounted on the clutch pedal. The switch is turned off when depressing the clutch pedal, and transmits a signal to the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0704 Clutch Switch Input Circuit No clutch switch signals to ECM despite gears being shifted.
(3 trip detection logic)
·

Open or short in clutch start switch assembly circuit

·

Clutch start switch assembly

·

ECM


Does not come on DTC stored

WIRING DIAGRAM

A311429E04
1.458,1.656 2.083,2.135 0.625,0.479 10 false EFI MAIN NO. 1 2.729,1.198 3.438,1.406 0.708,0.208 10 false EFI NO. 1 0.583,2.052 1.198,2.479 0.615,0.427 10 false EFI MAIN NO. 1 0.594,3.135 1.302,3.344 0.708,0.208 10 false FL MAIN 0.74,3.76 1.448,3.969 0.708,0.208 10 false Battery 3.521,1.542 5.104,1.927 1.583,0.385 10 false Clutch Start Switch Assembly 5.729,2.031 6.25,2.219 0.521,0.188 10 false MREL 6.188,3.99 6.604,4.229 0.417,0.24 10 false ECM 6.198,3.823 6.552,4.021 0.354,0.198 10 false A62 3.521,1.375 4.083,1.573 0.563,0.198 10 false A87*1 2.073,1.427 2.302,1.646 0.229,0.219 10 false 1 1.323,0.927 1.552,1.146 0.229,0.219 10 false 5 2.083,0.927 2.313,1.146 0.229,0.219 10 false 3 1.313,1.427 1.542,1.646 0.229,0.219 10 false 2 3.594,0.927 3.823,1.146 0.229,0.219 10 false 1 4.698,0.938 4.927,1.156 0.229,0.219 10 false 2 5.563,0.938 5.792,1.156 0.229,0.219 10 false 7 5.719,1.031 5.948,1.25 0.229,0.219 10 false D 5.552,2.021 5.781,2.24 0.229,0.219 10 false 9 4.208,3.875 5.896,4.073 1.688,0.198 10 false *1: for LHD 4.229,4.229 5.917,4.427 1.688,0.198 10 false *2: for RHD 4.104,1.375 4.667,1.573 0.563,0.198 10 false F1*2

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK CLUTCH START SWITCH ASSEMBLY
a.

Check the clutch start switch assembly installation.

OK:

Clutch start switch assembly is installed correctly.



Result:
Proceed to
OK
NG



OK

2.INSPECT CLUTCH START SWITCH ASSEMBLY

NG

10.SECURELY REINSTALL CLUTCH START SWITCH ASSEMBLY
2.INSPECT CLUTCH START SWITCH ASSEMBLY
a.

Inspect the clutch start switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - ECM)

NG

9.REPLACE CLUTCH START SWITCH ASSEMBLY
3.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - ECM)
a.

Disconnect the clutch start switch assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for LHD):
Tester Connection Condition Specified Condition
A87-2 - A62-7 (D) Always Below 1 Ω
A87-2 or A62-7 (D) - Body ground Always 10 kΩ or higher


Standard Resistance (for RHD):
Tester Connection Condition Specified Condition
F1-2 - A62-7 (D) Always Below 1 Ω
F1-2 or A62-7 (D) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
A311430C03
0.552,0.771 0.917,1 0.365,0.229 0.563,1.177 0.927,1.406 0.365,0.229 0.625,0.802 0.938,1 0.313,0.198 10 false A87 0.99,0.802 1.302,1 0.313,0.198 10 false *a 0.677,1.208 0.99,1.406 0.313,0.198 10 false F1 1,1.188 1.313,1.385 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to Clutch Start Switch Assembly (for LHD))
*b Front view of wire harness connector
(to Clutch Start Switch Assembly (for RHD))


a.

Disconnect the clutch start switch assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage (for LHD):
Tester Connection Switch Condition Specified Condition
A87-1 - Body ground Ignition switch ON 11 to 14 V


Standard Voltage (for RHD):
Tester Connection Switch Condition Specified Condition
F1-1 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.REPLACE ECM

NG

6.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - EFI MAIN NO. 1 RELAY)
5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - EFI MAIN NO. 1 RELAY)
a.

Disconnect the clutch start switch assembly connector.


b.

Remove the EFI MAIN NO. 1 relay from the engine room relay block and junction block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for LHD):
Tester Connection Condition Specified Condition
A87-1 - 3 (EFI MAIN NO. 1 relay holder) Always Below 1 Ω
A87-1 or 3 (EFI MAIN NO. 1 relay holder) - Body ground Always 10 kΩ or higher


Standard Resistance (for RHD):
Tester Connection Condition Specified Condition
F1-1 - 3 (EFI MAIN NO. 1 relay holder) Always Below 1 Ω
F1-1 or 3 (EFI MAIN NO. 1 relay holder) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK ECM POWER SOURCE CIRCUIT

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
7.CHECK ECM POWER SOURCE CIRCUIT

Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPLACE CLUTCH START SWITCH ASSEMBLY
a.

Replace the clutch start switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.SECURELY REINSTALL CLUTCH START SWITCH ASSEMBLY
a.

Securely reinstall the clutch start switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END