Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P1300  Reporting Error State on Comparing Energising Time #1  P1301  Reporting Error State on Comparing Energising Time #3  P1302  Reporting Error State on Comparing Energising Time #4  P1303  Reporting Error State on Comparing Energising Time #2  


DESCRIPTION

The injector assemblies are installed in the cylinder head and inject fuel into the cylinders based on the signals from the ECM.

HINT:
·

Injector driver is built into the ECM.

·

For more information on the injector assembly and fuel injection control, refer to System Description.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>SYSTEM DESCRIPTION



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1300 Reporting Error State on Comparing Energising Time #1 No. 1 injector assembly calibration time exceeds control time or signal error exceeds threshold.
(3 trip detection logic)
No. 1 injector assembly Does not come on DTC stored
P1301 Reporting Error State on Comparing Energising Time #3 No. 3 injector assembly calibration time exceeds control time or signal error exceeds threshold.
(3 trip detection logic)
No. 3 injector assembly Does not come on DTC stored
P1302 Reporting Error State on Comparing Energising Time #4 No. 4 injector assembly calibration time exceeds control time or signal error exceeds threshold.
(3 trip detection logic)
No. 4 injector assembly Does not come on DTC stored
P1303 Reporting Error State on Comparing Energising Time #2 No. 2 injector assembly calibration time exceeds control time or signal error exceeds threshold.
(3 trip detection logic)
No. 2 injector assembly Does not come on DTC stored

CAUTION / NOTICE / HINT

NOTICE:

When replacing the injector assembly, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION


HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
a.

Replace the injector assembly of malfunctioning cylinder.

Click hereEngine / Hybrid System>2WW FUEL>FUEL INJECTOR>REMOVAL


b.

Register the injector assembly compensation code.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>REGISTRATION


Result:
Proceed to
NEXT



NEXT

2.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END