Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P1320  Crankshaft Signal Diagnose - DGI Error  


DESCRIPTION

Refer to DTC P0335.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>P0335

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1320 Crankshaft Signal Diagnose - DGI Error One of following conditions is met (3 trip detection logic):
·

Crankshaft position sensor signal pulse width outside permissible range

·

Crankshaft position sensor signal estimated stopped position further outside permissible range than actual stopped position

·

Invalid, reverse pulse detected


·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

ECM


Does not come on DTC stored

Related Data List
DTC No. Data List
P1320 Engine Speed

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

When replacing the ECM and/or engine assembly, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION


HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Check the value on the GTS.

(a)Connect the GTS to the DLC3.

(b)Start the engine and turn the GTS on.

(c)Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

·

The engine speed can be confirmed in the Data List using the GTS. If there are no NE signals from the crankshaft position sensor despite the engine running, the engine speed will be indicated as zero. If the voltage output of the crankshaft position sensor is insufficient, the engine speed will be indicated as lower than the actual engine speed.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

Powertrain > Engine and ECT > Data List
Tester Display
Engine Speed
50003 371 7

d.

Read the value.

OK:

Less than 1000 rpm when the vehicle state is idling



Result:
Proceed to
OK
NG



OK

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

2.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
2.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Disconnect the crankshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B114-2 (NE) - B112-121 (NE+) Always Below 1 Ω
B114-3 (NE-) - B112-90 (NE-) Always Below 1 Ω
B114-1 (VG) - B112-122 (VCNE) Always Below 1 Ω
B114-2 (NE) or B112-121 (NE+) - Body ground Always 10 kΩ or higher
B114-3 (NE-) or B112-90 (NE-) - Body ground Always 10 kΩ or higher
B114-1 (VG) or B112-122 (VCNE) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
A351158C27
0.385,1.104 0.781,1.365 0.396,0.26 0.938,1.677 1.354,1.26 false 0.427,1.156 0.885,1.354 0.458,0.198 10 false B114 0.677,0.354 1.135,0.552 0.458,0.198 10 false *a 0.76,1.698 1.219,1.896 0.458,0.198 10 false VG
*a Front view of wire harness connector
(to Crankshaft Position Sensor)


a.

Disconnect the crankshaft position sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B114-1 (VG) - Body ground Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

4.REPLACE CRANKSHAFT POSITION SENSOR

NG

6.REPLACE ECM
4.REPLACE CRANKSHAFT POSITION SENSOR
a.

Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS
5.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
OK
NG



OK

END

NG

6.REPLACE ECM
6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END