Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P1470  Permanent Positive Governor Deviation  P1471  Permanent Negative Governor Deviation  P1472  Jammed Valve  P1474  Jammed Valve During Offset Learning  


DESCRIPTION

Refer to DTC P2016.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>P2016

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1470 Permanent Positive Governor Deviation The control error of the swirl control valve exceeds 5% and the measured position is less than 120% for 3 seconds or more.
(3 trip detection logic)
·

Open or short in swirl control valve circuit

·

Swirl control valve


Does not come on DTC stored
P1471 Permanent Negative Governor Deviation The control error of the swirl control valve exceeds -5% and the measured position is less than 120% for 3 seconds or more.
(3 trip detection logic)
·

Open or short in swirl control valve circuit

·

Swirl control valve


Does not come on DTC stored
P1472 Jammed Valve Even if the control error of the swirl control valve is not between -5% and 5% and 1.6 seconds elapse since the time the actuator operated, the control error does not recover for 3 seconds or more.
(3 trip detection logic)
·

Open or short in swirl control valve circuit

·

Swirl control valve


Does not come on DTC stored
P1474 Jammed Valve During Offset Learning The swirl control valve is unable to perform swirl-flap control within the specified time (3 seconds for open side, 4 seconds for close side) during the adaption phase.
(3 trip detection logic)
·

Open or short in swirl control valve circuit

·

Swirl control valve


Does not come on DTC stored

Related Data List
DTC No. Data List
P1470
P1471
P1472
P1474
Swirl Valve Actuator Position

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the swirl control valve, the ECM needs initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK SWIRL CONTROL VALVE
a.

Check for soot deposits inside the swirl control valve.

OK:

No soot deposits.


HINT:
·

If soot deposits are found, clean the swirl control valve.

·

If cleaning does not remove the soot deposits, replace the swirl control valve.




b.

Check for the operation mechanism of the swirl control valve for damage such as link deformation.

OK:

No damage.



c.

Check operation.

i.

Connect the GTS to the DLC3.


ii.

Turn the ignition switch to ON and turn the GTS on.


iii.

Start the engine.


iv.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Actuator Test of Swirl Flap / Data List / Swirl Valve Actuator Position.

Powertrain > Engine and ECT > Active Test
Active Test Display
Actuator Test of Swirl Flap
Data List Display
Swirl Valve Actuator Position
50004 371 7 198
OK:

The value of "Swirl Valve Actuator Position" changes according to the amount "Actuator Test of Swirl Flap" is operated, and the swirl flap operates smoothly.




Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (SWIRL CONTROL VALVE - ECM)

NG

4.REPLACE SWIRL CONTROL VALVE
2.CHECK HARNESS AND CONNECTOR (SWIRL CONTROL VALVE - ECM)
a.

Disconnect the swirl control valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B129-3 (SCV+) - B112-49 (IA1+) Always Below 1 Ω
B129-4 (SCV-) - B112-19 (IA1-) Always Below 1 Ω
B129-3 (SCV+) or B112-49 (IA1+) - Body ground Always 10 kΩ or higher
B129-4 (SCV-) or B112-19 (IA1-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE SWIRL CONTROL VALVE

NG

3.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.REPLACE SWIRL CONTROL VALVE
a.

Replace the swirl control valve.

Click hereEngine / Hybrid System>2WW INTAKE / EXHAUST>INTAKE MANIFOLD>REMOVAL


b.

Perform the swirl valve learning value reset.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END