Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P2016  Intake Manifold Runner Position Sensor/Switch Circuit Low Bank 1  P2017  Intake Manifold Runner Position Sensor/Switch Circuit High Bank 1  


DESCRIPTION

The swirl control valve is installed to the intake manifold and composed of the swirl flap, swirl flap actuator and swirl flap position sensor.

The position sensor is supplied with a voltage of 5 V by the ECM. The signal of the position sensor is an analogue voltage signal.

The controllable swirl flaps are located in the swirl ports. Depending on the operating range, the swirl flaps are activated with different duty cycles. The further the swirl flaps are closed, the more fresh air is drawn in exclusively through the swirl port. This increases the swirl of the drawn-in fresh air.

In the bottom load and engine speed range the swirl flaps are closed variably according to the operating range.

When the engine speed is approximately 2250 rpm or higher and the fuel injection volume is approximately 30 mg/stk or higher, the swirl flap is fully open.

The position of the swirl flaps is also corrected depending on the ambient pressure. At ambient pressures less than approximately 880 hPa, the swirl flaps tend to be opened further.

A342522E01
1.271,2.896 1.271,2.094 true 0.583,2.125 0.583,1.979 0.583,1.979 0.729,1.5 true 2.073,0.573 2.125,0.344 2.125,0.344 2.563,0.344 true 4.24,2.521 4.24,2.135 4.24,2.135 4.083,2.135 true 4.979,3.052 5.51,3.375 5.51,3.375 5.656,3.375 true 2.635,0.281 4.927,0.479 2.292,0.198 10 false Intake Manifold 0.354,2.125 2.646,2.323 2.292,0.198 10 false Linkage 0.281,2.948 3.031,3.26 2.75,0.313 10 false Swirl Flap Actuator and Position Sensor 5.719,3.271 7.156,3.469 1.438,0.198 10 false Swirl Flap 3.417,2.073 4.854,2.271 1.438,0.198 10 false Swirl Port

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2016 Intake Manifold Runner Position Sensor/Switch Circuit Low Bank 1 Swirl flap position sensor output voltage is 0.2 V or less for 0.22 seconds.
(3 trip detection logic)
·

Open or short in swirl control valve circuit

·

Swirl control valve

·

ECM


Comes on DTC stored
P2017 Intake Manifold Runner Position Sensor/Switch Circuit High Bank 1 Swirl flap position sensor output voltage is 4.85 V or more for 0.22 seconds.
(3 trip detection logic)
·

Open or short in swirl control valve circuit

·

Swirl control valve

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P2016
P2017
Swirl Valve Actuator Position

WIRING DIAGRAM

A342507E10
0.51,1.688 2.802,1.885 2.292,0.198 10 false Position Sensor 0.74,2.823 3.031,3.021 2.292,0.198 10 false Actuator 0.458,3.24 1.021,3.469 0.563,0.229 10 false B129 0.469,3.396 2.76,3.594 2.292,0.198 10 false Swirl Control Valve 1.594,0.5 3.885,0.698 2.292,0.198 10 false VCX 1.604,0.917 3.896,1.115 2.292,0.198 10 false VSX 1.615,1.313 3.906,1.51 2.292,0.198 10 false E2X 1.51,1.99 3.802,2.188 2.292,0.198 10 false SCV+ 1.542,2.427 3.833,2.625 2.292,0.198 10 false SCV- 2.01,0.49 4.302,0.688 2.292,0.198 10 false 5 2.021,0.885 4.313,1.083 2.292,0.198 10 false 1 2.021,1.313 4.313,1.51 2.292,0.198 10 false 2 2.01,1.979 4.302,2.177 2.292,0.198 10 false 3 2.01,2.406 4.302,2.604 2.292,0.198 10 false 4 5.323,0.49 7.156,0.688 1.833,0.198 10 false 72 5.323,0.896 7.156,1.094 1.833,0.198 10 false 87 5.26,1.323 7.094,1.521 1.833,0.198 10 false 119 5.323,1.979 7.156,2.177 1.833,0.198 10 false 49 5.323,2.427 7.156,2.625 1.833,0.198 10 false 19 5.625,0.5 7.156,0.719 1.531,0.219 10 false VAC1 5.635,1 7.156,1.219 1.521,0.219 10 false IAC1 5.635,1.427 7.156,1.646 1.521,0.219 10 false EAC1 5.635,2.104 7.156,2.323 1.521,0.219 10 false IA1+ 5.635,2.521 7.156,2.74 1.521,0.219 10 false IA1- 5.99,3.052 6.458,3.26 0.469,0.208 10 false B112 6,3.219 6.948,3.438 0.948,0.219 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

After replacing the swirl control valve, the ECM needs initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION



HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ACTUATOR TEST OF SWIRL FLAP)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Actuator Test of Swirl Flap / Data List / Swirl Valve Actuator Position.

Powertrain > Engine and ECT > Active Test
Active Test Display
Actuator Test of Swirl Flap
Data List Display
Swirl Valve Actuator Position
50004 371 7 198
OK:

The value of "Swirl Valve Actuator Position" changes according to the amount "Actuator Test of Swirl Flap" is operated, and the swirl flap operates smoothly.



Result:
Proceed to
OK
NG



OK

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

2.CHECK HARNESS AND CONNECTOR (SWIRL CONTROL VALVE - ECM)
2.CHECK HARNESS AND CONNECTOR (SWIRL CONTROL VALVE - ECM)
a.

Disconnect the swirl control valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B129-3 (SCV+) - B112-49 (IA1+) Always Below 1 Ω
B129-4 (SCV-) - B112-19 (IA1-) Always Below 1 Ω
B129-5 (VCX) - B112-72 (VAC1) Always Below 1 Ω
B129-1 (VSX) - B112-87 (IAC1) Always Below 1 Ω
B129-2 (E2X) - B112-119 (EAC1) Always Below 1 Ω
B129-3 (SCV+) or B112-49 (IA1+) - Body ground Always 10 kΩ or higher
B129-4 (SCV-) or B112-19 (IA1-) - Body ground Always 10 kΩ or higher
B129-5 (VCX) or B112-72 (VAC1) - Body ground Always 10 kΩ or higher
B129-1 (VSX) or B112-87 (IAC1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (VC VOLTAGE)

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK HARNESS AND CONNECTOR (VC VOLTAGE)
A351162C05
0.104,1.094 0.521,1.354 0.417,0.26 0.813,1.698 1.146,1.26 false 2.313,1.729 2.01,1.271 false 0.188,0.146 0.5,0.302 0.313,0.156 10 false *a 0.156,1.146 0.75,1.365 0.594,0.219 10 false B129 0.677,1.781 1.271,2 0.594,0.219 10 false VCX 2.25,1.792 2.844,2.01 0.594,0.219 10 false E2X
*a Front view of wire harness connector
(to Swirl Control Valve)


a.

Disconnect the swirl control valve connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B129-5 (VCX) - B129-2 (E2X) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

4.REPLACE SWIRL CONTROL VALVE

NG

6.REPLACE ECM
4.REPLACE SWIRL CONTROL VALVE
a.

Replace the swirl control valve.

Click hereEngine / Hybrid System>2WW INTAKE / EXHAUST>INTAKE MANIFOLD>REMOVAL


b.

Perform the swirl valve learning value reset.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P2016 AND/OR P2017)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P2016 AND/OR P2017)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Read the DTCs.

Result:
Result Proceed to
No DTC output A
DTC P2016 and/or P2017 B




A

END

B

6.REPLACE ECM
6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END