Home › Engine / Hybrid System › 2WW INTAKE / EXHAUST › INTAKE MANIFOLD › from 2015.10
RM3090E _51 Engine / Hybrid System _044376 2WW INTAKE / EXHAUST _0210931 INTAKE MANIFOLD A

2WW INTAKE / EXHAUST  INTAKE MANIFOLD  REMOVAL  


PROCEDURE

Hide 22030 1.REMOVE DIESEL THROTTLE BODY ASSEMBLY

Hide 3.DISCONNECT ENGINE WIRE

a.
A313578

Detach the 2 clamps and disconnect the glow plug controller assembly harness connector.


b.
A337402

Disconnect the EGR gas temperature sensor connector.


c.

Detach the 6 clamps and disconnect the fuel quantity control valve connector.


d.
A337403

Disconnect the swirl control valve connector.


e.

Disconnect the fuel pressure sensor connector.


f.

Disconnect the engine coolant temperature sensor connector.


g.

Disconnect the generator assembly connector.


h.

Disconnect the camshaft position sensor connector.


i.

Disconnect the turbo pressure sensor assembly connector.


j.

Disconnect the 2 glow plug controller assembly connectors.


k.

Detach the 2 clamps.


l.

Using a T25 "TORX" socket wrench, remove the screw and disconnect the engine wire.


Hide 11409 4.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Remove the engine oil level dipstick.


b.
A313582

Detach the clamp and disconnect the fuel feed pipe sub-assembly from the engine oil level dipstick guide.


c.

Using a T25 "TORX" socket wrench, remove the bolt and engine oil level dipstick guide.


d.

Remove the O-ring from the engine oil level dipstick guide.


Hide 5.DISCONNECT NO. 2 VACUUM HOSE ASSEMBLY

a.
A316715C01
1.229,0.615 1.354,0.615 1.354,0.615 1.49,1.229 true 1.01,0.531 1.25,0.74 0.24,0.208 10 true *1
*1 No. 1 Vacuum Pipe


Disconnect the No. 2 vacuum hose assembly from the No. 1 vacuum pipe.

i.

Check that there is no damage or foreign matter on the part of the No. 1 vacuum pipe that contacts the No. 2 vacuum hose assembly connector.


ii.
A316716C01
2.75,1.531 2.75,1.354 2.75,1.354 2.875,1.146 false 2.885,0.417 2.76,0.177 2.76,0.177 2.604,0.177 false 2.688,1.573 2.896,1.792 0.208,0.219 10 false *a 2.365,0.104 2.573,0.323 0.208,0.219 10 false *a
*a Retainer
V100135

Pinch
V100136

Pull out


If the No. 2 vacuum hose assembly connector and No. 1 vacuum pipe are stuck together, hold the No. 1 vacuum pipe by hand and push and pull on the No. 2 vacuum hose assembly connector.

NOTICE:
·

Check for any dirt and foreign matter in the No. 1 vacuum pipe and around the No. 2 vacuum hose assembly connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the No. 1 vacuum pipe and No. 2 vacuum hose assembly connector.

·

Do not use any tools to separate the No. 1 vacuum pipe and No. 2 vacuum hose assembly connector.

·

Check for any dirt and foreign matter on the No. 1 vacuum pipe seal surface. Clean if necessary.

·

Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the No. 2 vacuum hose assembly.

·

If the No. 1 vacuum pipe and No. 2 vacuum hose assembly connector are stuck together, pinch the No. 2 vacuum hose assembly connector between your fingers and turn it carefully to free it. Then disconnect the No. 2 vacuum hose assembly.




iii.

Check for dirt or mud on the No. 1 vacuum pipe seal surface of the disconnected No. 1 vacuum pipe. Clean if necessary.


iv.

To protect the disconnected No. 1 vacuum pipe and No. 2 vacuum hose assembly connector from damage and contamination, cover them with a plastic bag and tape.



Hide 25733A 6.REMOVE NO. 1 VACUUM PIPE

a.
A313583

Disconnect the vacuum hose.


b.

Using an E7 "TORX" socket wrench, remove the bolt and No. 1 vacuum pipe from the cylinder block sub-assembly.


c.

Remove the O-ring from the No. 1 vacuum pipe.


Hide 17111 7.REMOVE INTAKE MANIFOLD

a.
A337404C01
2.948,1.313 3.104,1.51 0.156,0.198 10 true 1 2.135,0.552 2.292,0.771 0.156,0.219 10 true 2 2.302,1.635 2.458,1.854 0.156,0.219 10 true 7 2.031,2.885 2.188,3.104 0.156,0.219 10 true 5 1.24,1.417 1.396,1.635 0.156,0.219 10 true 3 0.469,2.917 0.625,3.135 0.156,0.219 10 true 4 0.073,1.531 0.229,1.75 0.156,0.219 10 true 6
V100135

Bolt (A)
V100136

Bolt (B)


Remove the bolt (B) and loosen the 6 bolts (A) in the order shown in the illustration, and then remove the intake manifold.

HINT:

The bolts (A) in the illustration cannot be removed from the intake manifold.



b.
A337405

Remove the 4 gaskets from the intake manifold.


c.

Remove the gasket from the No. 2 EGR pipe.


Hide 28550 9.REMOVE GLOW PLUG CONTROLLER ASSEMBLY

Hide 25612A 11.REMOVE NO. 2 EGR PIPE

a.
A337406

Remove the No. 2 EGR pipe from the intake manifold.


b.
A313587C01
1.156,0.25 1.365,0.25 1.365,0.25 1.458,0.563 false 0.927,0.167 1.24,0.365 0.313,0.198 10 false *1
*1 O-ring


Remove the O-ring from the No. 2 EGR pipe.


Hide 12.REMOVE SWIRL CONTROL VALVE

a.
A343588C01
0.708,1.188 0.583,0.458 0.583,0.458 0.375,0.458 true 0.177,0.385 0.49,0.583 0.313,0.198 8 false *a
*a Rod


Detach the rod from the swirl control valve.


b.

Remove the 3 bolts and swirl control valve from the intake manifold.