Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P2454  Diesel Particulate Filter Pressure Sensor "A" Circuit Low  P2455  Diesel Particulate Filter Pressure Sensor "A" Circuit High  


DESCRIPTION

The two sensing chambers of the differential pressure sensor are mounted to monitor the pressure before and after the DPF catalytic converter.

The ECM compares the exhaust gas pressure before and after the DPF catalytic converter by monitoring the pressure using the upstream and downstream sensing chambers of the differential pressure sensor. If the difference between the pressure before and after the DPF catalytic converter exceeds a predetermined level, the ECM judges that the catalytic converter is clogged with particulate matter (PM).

When the ECM judges that a partially clogged condition exists, the ECM begins to perform PM forced regeneration.

When the output voltage of the sensor deviates from the normal operating range, the ECM interprets this as a malfunction of the sensor circuit, and sets DTC P2454 or P2455, and illuminates the MIL.

A342508E01
4.031,1.063 4.375,1.01 false 4.135,1.25 4.375,1.052 false 4.656,1.156 4.573,0.958 false 5.021,2.865 4.99,2.51 4.99,2.51 5.125,2.51 false 2.802,2.76 2.677,2.396 false 0.719,2.771 1.25,2.01 false 1.26,0.573 2.948,0.771 1.688,0.198 10 false Exhaust Gas 2.865,0.521 4.552,0.719 1.688,0.198 10 false ECM 0.354,2.781 1.26,3.208 0.906,0.427 10 false DPF Catalytic Converter 2.365,2.781 3.646,3.292 1.281,0.51 10 false Differential Pressure Sensor 3.927,0.125 6.583,0.365 2.656,0.24 10 false Property of Output Voltage: 3.99,0.458 6.646,0.698 2.656,0.24 10 false Differential Pressure Voltage (V) 3.948,0.813 4.542,1.042 0.594,0.229 10 false 5.000 3.604,1 4.198,1.229 0.594,0.229 10 false 4.800 3.729,1.229 4.323,1.458 0.594,0.229 10 false 4.500 3.948,2.479 4.542,2.708 0.594,0.229 10 false 1.000 3.948,2.625 4.542,2.854 0.594,0.229 10 false 0.825 3.948,2.76 4.542,2.99 0.594,0.229 10 false 0.700 4.24,3.021 4.833,3.25 0.594,0.229 10 false 0 4.49,3.125 5.083,3.354 0.594,0.229 10 false -5 4.708,3.125 5.302,3.354 0.594,0.229 10 false 0 6.406,3.135 7,3.365 0.594,0.229 10 false 100.0 4.5,1.177 7.156,1.417 2.656,0.24 10 false Stores P2455 5.177,2.417 6.292,2.708 1.115,0.292 10 false Stores P2454 4.208,3.385 7,3.625 2.792,0.24 10 false Exhaust Gas Differential Pressure (kPa)

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2454 Diesel Particulate Filter Pressure Sensor "A" Circuit Low Differential pressure sensor output voltage is 0.7 V or less for 0.6 seconds.
(3 trip detection logic)
·

Open or short in differential pressure sensor circuit

·

Differential pressure sensor

·

ECM


Comes on DTC stored
P2455 Diesel Particulate Filter Pressure Sensor "A" Circuit High Differential pressure sensor output voltage is 4.8 V or more 0.6 seconds.
(3 trip detection logic)
·

Open or short in differential pressure sensor circuit

·

Differential pressure sensor

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P2454
P2455
Adaptation Value of Differential Pressure at Particle Filter

WIRING DIAGRAM

A165731E76
0.406,2.052 0.896,2.281 0.49,0.229 10 false B127 0.396,2.229 2.531,2.552 2.135,0.323 10 false Differential Pressure Sensor 6.052,2.052 6.5,2.281 0.448,0.229 10 false B112 6.073,2.208 6.5,2.385 0.427,0.177 10 false ECM 1.542,1.583 1.969,1.844 0.427,0.26 10 false E2 1.427,1.052 1.885,1.292 0.458,0.24 10 false PEX 1.5,0.469 1.75,0.677 0.25,0.208 10 false VC 5.688,1.573 6.271,1.813 0.583,0.24 10 false EPEX 5.688,1.052 6.052,1.25 0.365,0.198 10 false PEX 5.677,0.469 6.177,0.688 0.5,0.219 10 false VCPX 1.823,0.354 1.99,0.573 0.167,0.219 10 false 1 1.844,0.927 1.969,1.104 0.125,0.177 10 false 2 1.844,1.479 1.969,1.656 0.125,0.177 10 false 3 5.385,0.365 5.594,0.552 0.208,0.188 10 false 70 5.406,0.938 5.667,1.115 0.26,0.177 10 false 85 5.385,1.469 5.656,1.646 0.271,0.177 10 false 71

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

After replacing the differential pressure sensor, the ECM needs initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION



HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (ADAPTATION VALUE OF DIFFERENTIAL PRESSURE AT PARTICLE FILTER)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Adaptation Value of Differential Pressure at Particle Filter.

Powertrain > Engine and ECT > Data List
Tester Display
Adaptation Value of Differential Pressure at Particle Filter
50003 371 116

d.

Start the engine.


e.

Read the values while revving the engine at high speeds.

OK:

The values in the Data List change according to changes in the engine speed.



Result:
Proceed to
OK
NG



OK

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

2.CHECK HARNESS AND CONNECTOR (DIFFERENTIAL PRESSURE SENSOR - ECM)
2.CHECK HARNESS AND CONNECTOR (DIFFERENTIAL PRESSURE SENSOR - ECM)
a.

Disconnect the differential pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B127-1 (VC) - B112-70 (VCPX) Always Below 1 Ω
B127-2 (PEX) - B112-85 (PEX) Always Below 1 Ω
B127-3 (E2) - B112-71 (EPEX) Always Below 1 Ω
B127-1 (VC) or B112-70 (VCPX) - Body ground Always 10 kΩ or higher
B127-2 (PEX) or B112-85 (PEX) - Body ground Always 10 kΩ or higher
B127-3 (E2) or B112-71 (EPEX) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (VC VOLTAGE)

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK HARNESS AND CONNECTOR (VC VOLTAGE)
A351158C26
0.302,1.146 0.75,1.365 0.448,0.219 0.948,1.792 1.354,1.281 true 2.438,1.792 2.083,1.281 true 0.188,0.177 0.5,0.333 0.313,0.156 10 false *a 0.375,1.167 0.844,1.365 0.469,0.198 10 false B127 0.844,1.813 1.313,2.01 0.469,0.198 10 false VC 2.396,1.813 2.865,2.01 0.469,0.198 10 false E2
*a Front view of wire harness connector
(to Differential Pressure Sensor)


a.

Disconnect the differential pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B127-1 (VC) - B127-3 (E2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

4.REPLACE DIFFERENTIAL PRESSURE SENSOR

NG

6.REPLACE ECM
4.REPLACE DIFFERENTIAL PRESSURE SENSOR
a.

Replace the differential pressure sensor.

Click hereEngine / Hybrid System>2WW EMISSION CONTROL>DIFFERENTIAL PRESSURE SENSOR>REMOVAL


b.

Perform differential pressure learning value reset.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P2454 OR P2455)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P2454 OR P2455)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Read the DTCs.

Result:
Result Proceed to
No DTC output A
DTC P2454 or P2455 B




A

END

B

6.REPLACE ECM
6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END