Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P2620  Throttle Position Output Circuit / Open  P2621  Throttle Position Output Circuit Low  P2622  Throttle Position Output Circuit High  


DESCRIPTION

Refer to DTC P0122.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>P0122

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2620 Throttle Position Output Circuit / Open Open or short in diesel throttle body assembly circuit for 0.22 seconds.
(3 trip detection logic)
·

Open or short in diesel throttle body assembly circuit

·

Diesel throttle body assembly

·

ECM


Does not come on DTC stored
P2621 Throttle Position Output Circuit Low Short to ground in diesel throttle body assembly circuit for 0.22 seconds.
(3 trip detection logic)
·

Open or short in diesel throttle body assembly circuit

·

Diesel throttle body assembly

·

ECM


Does not come on DTC stored
P2622 Throttle Position Output Circuit High Short to +B in diesel throttle body assembly circuit for 0.22 seconds.
(3 trip detection logic)
·

Open or short in diesel throttle body assembly circuit

·

Diesel throttle body assembly

·

ECM


Does not come on DTC stored

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION


HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (DIESEL THROTTLE BODY ASSEMBLY - ECM)
a.

Disconnect the diesel throttle body assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
o1-4 (M+) - B112-50 (M+) Always Below 1 Ω
o1-5 (M-) - B112-20 (M-) Always Below 1 Ω
o1-4 (M+) or B112-50 (M+) - Body ground Always 10 kΩ or higher
o1-5 (M-) or B112-20 (M-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.REPLACE DIESEL THROTTLE BODY ASSEMBLY

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.REPLACE DIESEL THROTTLE BODY ASSEMBLY
a.

Replace the diesel throttle body assembly.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>DIESEL THROTTLE BODY>REMOVAL


Result:
Proceed to
NEXT



NEXT

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2620, P2621 AND/OR P2622)
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2620, P2621 AND/OR P2622)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Read the DTC.

Result:
Result Proceed to
No DTC output A
DTC P2620, P2621 and/or P2622 B




A

END

B

4.REPLACE ECM
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED