Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P3280  FBC Correction Quantities at Limitation  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P3280 FBC Correction Quantities at Limitation Correction quantity in impermissible range for 15 seconds.
(3 trip detection logic)
·

Injector assembly

·

Cylinder compression pressure


Does not come on DTC stored

CAUTION / NOTICE / HINT

NOTICE:

When replacing the ECM, injector assembly and/or engine assembly, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION


HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (FUEL BALANCING COMPENSATION (FBC))
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Fuel Balancing Compensation (FBC) / Data List / Cylinder 1 Quantity Compensation to Cylinder 4 Quantity Compensation.

Powertrain > Engine and ECT > Active Test
Active Test Display
Fuel Balancing Compensation (FBC)
Data List Display
Cylinder 1 Quantity Compensation
Cylinder 2 Quantity Compensation
Cylinder 3 Quantity Compensation
Cylinder 4 Quantity Compensation
50004 371 16 110,111,112,113

e.

Read the value.

Standard Value:

-5.0 to 4.0 mg/stk


HINT:
·

If a malfunction is found during this inspection, the fuel injector may be stuck open.

·

If a malfunction is not found in the fuel injector, the probable cause may be a loss of compression pressure, the formation of soot deposits in the intake system or an excessively high or low injection volume.




Result:
Proceed to
OK
NG



OK

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

2.CHECK CYLINDER COMPRESSION PRESSURE
2.CHECK CYLINDER COMPRESSION PRESSURE
a.

Check the cylinder compression pressure.

Click hereEngine / Hybrid System>2WW ENGINE MECHANICAL>ENGINE>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

3.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER

NG

4.CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
3.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
a.

Replace the injector assembly.

Click hereEngine / Hybrid System>2WW FUEL>FUEL INJECTOR>REMOVAL

HINT:
·

Confirm which injector assemblies to replace using the quantity compensation values of cylinders 1 to 4.

·

If a value varies, replace the injector assembly of that cylinder.

·

If no values vary, replace all the injector assemblies.




b.

Register the injector compensation code.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>REGISTRATION


Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END