When the engine is cranked, the ST (starter) relay drive signal is input to the STA terminal of the ECM, and the NE signal generated by the crankshaft position sensor is also input to the NE+ terminal. Thus, the ECM interprets that the engine has been cranked, current flows to the FUEL PUMP relay, and the fuel pump (fuel suction with pump and gauge tube assembly) operates.
While the NE signal is input to the ECM with the engine running, the fuel pump operates continuously.
When replacing the ECM, the ECM needs registration and initialization.
Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Actuator Test of FPC.
| Tester Display |
|---|
| Actuator Test of FPC |
Check whether the fuel pump operating sound occurs when performing the Active Test on the GTS.
| Result | Proceed to |
|---|---|
| Fuel pump operating sound does not occur | A |
| Fuel pump operating sound occurs | B |
A
B
Inspect the fuel pump relay (FUEL PMP).
Click hereEngine / Hybrid System>2WW ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the fuel pump relay (FUEL PMP) from the engine room relay block and junction block.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (Fuel pump relay (FUEL PMP) holder) - A62-60 (FC) | Always | Below 1 Ω |
| 1 (Fuel pump relay (FUEL PMP) holder) or A62-60 (FC) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the fuel pump relay (FUEL PMP) from the engine room relay block and junction block.
Remove the IG2 relay from the engine room relay block and junction block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (Fuel pump relay (FUEL PMP) holder) - 5 (IG2 relay holder) | Always | Below 1 Ω |
| 2 (Fuel pump relay (FUEL PMP) holder) or 5 (IG2 relay holder) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the fuel pump relay (FUEL PMP) from the engine room relay block and junction block.
Disconnect the fuel pump (fuel suction with pump and gauge tube assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (Fuel pump relay (FUEL PMP) holder) - V1-4 (B) | Always | Below 1 Ω |
| V1-5 (E) - Body ground | Always | Below 1 Ω |
| 3 (Fuel pump relay (FUEL PMP) holder) or V1-4 (B) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the fuel pump (fuel suction with pump and gauge tube assembly).
Click hereEngine / Hybrid System>2WW FUEL>FUEL PUMP>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG