Home › Engine / Hybrid System › 3ZR-FE ENGINE MECHANICAL › ENGINE UNIT › from 2015.10
RM3090E _51 Engine / Hybrid System _008405 3ZR-FE ENGINE MECHANICAL _0046950 ENGINE UNIT A

3ZR-FE ENGINE MECHANICAL  ENGINE UNIT  DISASSEMBLY  


PROCEDURE

Hide 12108 1.REMOVE OIL FILLER CAP SUB-ASSEMBLY

a.
A150846

Remove the oil filler cap sub-assembly.


Hide 12108A 2.REMOVE OIL FILLER CAP GASKET

a.
A128159

Remove the oil filler cap gasket.


Hide 12635 3.REMOVE ENGINE COVER JOINT

a.
A150847

Remove the 2 engine cover joints.


Hide 11101W 5.REMOVE CAMSHAFT POSITION SENSOR (for Intake Side)

Hide 6.REMOVE CAMSHAFT POSITION SENSOR (for Exhaust Side)

Hide 11101J 7.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Intake Side)

Hide 8.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Exhaust Side)

Hide 11401G 9.REMOVE CRANKSHAFT POSITION SENSOR

Hide 83530 10.REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY

Hide 89422 12.REMOVE ENGINE COOLANT TEMPERATURE SENSOR

Hide 11201 13.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A150850

Remove the 13 bolts, seal washer and cylinder head cover sub-assembly.


b.
A150852

Remove the 3 gaskets from the camshaft bearing cap.

NOTICE:

As gaskets may stick to the cylinder head cover, be careful not to drop any of the gaskets into the engine when removing the cylinder head cover.



Hide 11213 14.REMOVE CYLINDER HEAD COVER GASKET

a.
A150851

Remove the cylinder head cover gasket.


Hide 11193 15.REMOVE SPARK PLUG TUBE GASKET

a.
A152586

Pry up the 4 claws of the ventilation baffle plate.

NOTICE:

Do not deform the claws of the ventilation baffle plate more than necessary.



b.
A337770

Using a screwdriver as shown in the illustration, deform each spark plug tube gasket inwards and remove the 4 spark plug tube gaskets from cylinder head cover sub-assembly.

NOTICE:
·

As much as possible prevent the spark plug tube gaskets from being deformed.

·

Do not damage the spark plug tube gasket and cylinder head cover sub-assembly.

·

Make sure not to damage the spark plug tube gasket and cylinder head cover sub-assembly when inserting the screwdriver in the joint area.



HINT:

If the cylinder head cover sub-assembly is damaged, smooth the surface with 400-grid sandpaper.



Hide 15600A 17.REMOVE OIL FILTER UNION (for Oil Filter Sub-assembly Type)

a.
A150866

Using a 12 mm socket hexagon wrench, remove the oil filter union.


Hide 18.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.
A234710C02
1.229,1.76 1.885,2.365 1.885,2.365 2.521,1.802 true 1.292,3.115 0.479,3.271 true 1.208,3.281 0.781,3.813 true 1.792,2.406 2.073,2.625 0.281,0.219 10 *1 0.24,3.198 0.521,3.427 0.281,0.229 10 *1 0.615,3.833 0.896,4.073 0.281,0.24 10 *2
*1 Timing Mark
*2 Timing Notch


Turn the crankshaft pulley until its timing notch and timing mark "0" of the timing chain cover are aligned.


b.

Check that the timing marks on both the camshaft timing exhaust gear and camshaft timing gear are facing upward as shown in the illustration.

HINT:

If the marks are not as shown, turn the crankshaft 1 complete revolution (360°) and align the marks as specified above.



Hide 13540 20.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A250765

Remove the 2 nuts, bracket, No. 1 chain tensioner assembly and gasket.

NOTICE:

Do not turn the crankshaft without the No. 1 chain tensioner assembly installed.



Hide 21.REMOVE ENGINE MOUNTING BRACKET STUD BOLT

a.
A211980

Remove the engine mounting bracket stud bolt.


Hide 11302 22.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

Hide 11302A 23.REMOVE TIMING CHAIN COVER OIL SEAL

Hide 16323 24.REMOVE WATER INLET HOUSING

a.
A150906

Remove the 3 bolts, water inlet housing and gasket.


Hide 12511 25.REMOVE NO. 1 GENERATOR BRACKET

a.
A150905

Remove the 4 bolts and No. 1 generator bracket.


Hide 13559 26.REMOVE CHAIN TENSIONER SLIPPER

A150870

Hide 13561 27.REMOVE NO. 1 CHAIN VIBRATION DAMPER

a.
A165280

Remove the 2 bolts and No. 1 chain vibration damper.


Hide 13562 28.REMOVE NO. 2 CHAIN VIBRATION DAMPER

Hide 13506 29.REMOVE CHAIN SUB-ASSEMBLY

a.
A251821C01
2.677,1.99 2.875,1.271 2.875,1.271 3.01,1.271 true 1.375,3.76 1.552,3.323 1.552,3.323 1.635,3.323 true 1.74,0.052 1.969,0.26 0.229,0.208 10 *a 3.052,1.188 3.365,1.417 0.313,0.229 10 *b 1.646,3.229 1.917,3.469 0.271,0.24 10 *c
*a Turn
*b Place the Chain on the Gear
*c Loosen the Chain


Hold the hexagonal portion of the camshaft with a wrench and turn the camshaft timing gear assembly counterclockwise to loosen the chain sub-assembly between the camshaft timing gears.


b.

With the chain sub-assembly loosened, release the chain sub-assembly from the camshaft timing gear assembly and place it on the camshaft timing gear assembly.

HINT:

Be sure to release the chain sub-assembly from the sprocket completely.



c.

Turn the camshaft clockwise to return it to the original position and remove the chain sub-assembly.


Hide 13521 30.REMOVE CRANKSHAFT TIMING SPROCKET

Hide 13507 31.REMOVE NO. 2 CHAIN SUB-ASSEMBLY

Hide 19315 32.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

Hide 13521A 33.REMOVE CRANKSHAFT TIMING GEAR KEY

a.
A150909C07
0.672,0.666 0.837,0.828 0.165,0.162 10 *1 0.857,0.763 0.964,0.763 0.964,0.763 1.178,1.335 false
*1 Protective Tape


Using a screwdriver, remove the 2 crankshaft timing gear keys.

HINT:

Tape the screwdriver tip before use.



Hide 13050 34.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13070A 35.INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

Hide 13050 36.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13070A 37.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

Hide 38.REMOVE CAMSHAFT BEARING CAP

Hide 13512 40.REMOVE NO. 2 CAMSHAFT

Hide 13801 41.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.
A332534

Remove the 16 No. 1 valve rocker arm sub-assemblies.

HINT:

Arrange the removed parts in the correct order.



Hide 13750 42.REMOVE VALVE LASH ADJUSTER ASSEMBLY

a.
A297858

Remove the 16 valve lash adjuster assemblies from the cylinder head.

HINT:

Arrange the removed parts in the correct order.



Hide 15678A 43.REMOVE OIL CONTROL VALVE FILTER

a.
A150883

Remove the oil control valve filter from the No. 1 camshaft bearing cap.


Hide 11811 44.REMOVE NO. 1 CAMSHAFT BEARING

Hide 11821 45.REMOVE NO. 2 CAMSHAFT BEARING

Hide 11103 46.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY

Hide 13716 47.REMOVE VALVE STEM CAP

a.
A150945

Remove the 16 valve stem caps.

HINT:

Arrange the removed parts in the correct order.



Hide 11114A 48.REMOVE CAMSHAFT HOUSING STRAIGHT PIN

NOTICE:

It is not necessary to remove a straight pin unless it is being replaced.


Hide 11101 49.REMOVE CYLINDER HEAD SUB-ASSEMBLY

Hide 12204 51.REMOVE PCV VALVE SUB-ASSEMBLY

Hide 12101A 52.REMOVE OIL PAN DRAIN PLUG

a.
A150893

Remove the oil pan drain plug and gasket.


Hide 12102A 53.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

Hide 15100 54.REMOVE OIL PUMP ASSEMBLY

Hide 11420 56.REMOVE STIFFENING CRANKCASE ASSEMBLY

a.
A150897

Uniformly loosen and remove the 11 bolts.


b.
A150898C09
0.448,3.083 0.604,3.49 0.604,3.49 0.604,3.615 true 1.177,3.573 1.344,3.979 1.344,3.979 1.344,4.104 true 2.479,3.396 2.646,3.802 2.646,3.802 2.646,3.927 true 3.083,2.688 3.25,3.083 3.25,3.083 3.25,3.208 true 0.521,3.646 0.719,3.833 0.198,0.188 10 *1 1.25,4.135 1.448,4.323 0.198,0.188 10 *1 2.552,3.938 2.75,4.125 0.198,0.188 10 *1 3.167,3.25 3.365,3.438 0.198,0.188 10 *1
*1 Protective Tape


Using a screwdriver, remove the stiffening crankcase assembly by prying between the stiffening crankcase and cylinder block.

NOTICE:

Be careful not to damage the contact surfaces of the stiffening crankcase and cylinder block.


HINT:

Tape the screwdriver tip before use.



Hide 11432A 57.REMOVE NO. 1 TAPER SCREW PLUG

a.
A300838

Remove the No. 1 taper screw plug.


Hide 58.REMOVE STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


Hide 59.REMOVE STIFFENING CRANKCASE RING PIN

NOTICE:

It is not necessary to remove a ring pin unless it is being replaced.