Home › Drivetrain › K114 MULTIDRIVE / CVT › TRANSMISSION CONTROL CABLE › from 2015.10
RM3090E _52 Drivetrain _044380 K114 MULTIDRIVE / CVT _0212489 TRANSMISSION CONTROL CABLE A

K114 MULTIDRIVE / CVT  TRANSMISSION CONTROL CABLE  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 3.DISCONNECT CABLE FROM POSITIVE BATTERY TERMINAL

Hide 11212 4.REMOVE NO. 2 CYLINDER HEAD COVER

Hide 17705 5.REMOVE AIR CLEANER CAP SUB-ASSEMBLY

Hide 17801 6.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Remove the air cleaner filter element sub-assembly from the air cleaner case sub-assembly.


Hide 7.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 74404A 8.REMOVE BATTERY CLAMP SUB-ASSEMBLY

Hide 28800 9.REMOVE BATTERY

Hide 74431 10.REMOVE BATTERY TRAY

Hide 16057 11.DISCONNECT RADIATOR HOSE SUB-ASSEMBLY

Hide 74411B 12.REMOVE FRONT BATTERY BRACKET

Hide 74414B 13.REMOVE BATTERY BRACKET REINFORCEMENT

Hide 50819 14.REMOVE FRONT FLOOR COVER

Hide 58901A 15.REMOVE REAR CONSOLE BOX ASSEMBLY

Hide 33820B 16.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.

Move the shift lever to N.


b.
C328346C01
1.896,1.563 2.01,1.438 false
V113147

Disconnect in this Direction


Disconnect the end of the transmission control cable assembly from the shift lever assembly.


c.
C328347C01
1.198,0.906 1.25,0.719 false 1.833,0.667 2.167,0.167 2.167,0.167 2.521,0.167 true 0.906,0.302 1.25,0.302 1.25,0.302 1.49,0.781 true 2.583,0.083 2.896,0.281 0.313,0.198 10 false *1 0.719,0.219 1.031,0.417 0.313,0.198 10 false *2
*1 Stopper
*2 Nut
V113147

Turn in this Direction
V113148

Pull out in this Direction


Pull out the stopper of the transmission control cable assembly.


d.

Turn the nut of the transmission control cable assembly counterclockwise approximately 180° and, while holding the nut in that position, disconnect the transmission control cable assembly from the shift lever assembly.

NOTICE:

Do not over-rotate the nut as it will come off the internal spring and the transmission control cable assembly will not be reusable.



Hide 33820B 17.REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C296239

Remove the nut and disconnect the transmission control cable assembly from the control shaft lever.


b.

Remove the clip and disconnect the transmission control cable assembly from the No. 1 transmission control cable bracket.


c.
C296306

Remove the nut and disconnect the transmission control cable assembly from the transmission control cable support.


d.
C344354

Remove the bolt and disconnect the transmission control cable assembly from the rear engine mounting insulator.


e.
C296270

Remove the 2 bolts and transmission control cable assembly.