Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD GLASS › from 2015.10
RM3090E _59 Vehicle Exterior _008792 WINDOW / GLASS _0050080 WINDSHIELD GLASS A

WINDOW / GLASS  WINDSHIELD GLASS  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the windshield glass of a vehicle equipped with a forward recognition camera, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the forward recognition camera may not be able to be installed due to a missing bracket, or the lane departure alert system, front recognition camera system, dynamic radar cruise control system, pre-crash safety system or automatic high beam system may not operate properly due to a difference in the transmissivity of the windshield glass or the shape of the black ceramic border.

·

Make sure to use Toyota Genuine Windshield Glass Adhesive (High Modulus Type) or an equivalent high modulus adhesive.

·

For models with a heated windshield defroster system, there are non-replacable dams and sealers on the windshield glass at the positions shown in the illustration. When removing and installing the windshield glass, make sure not to damage the dams and sealers with a wire or knife. If the dams and sealers are damaged, replace the windshield glass.

B435757C01
3.417,1.604 3.708,1.875 0.292,0.271 10 false A 3.875,0.854 4.031,1.052 0.156,0.198 10 true A 4.865,0.74 5.635,0.938 0.771,0.198 10 false A - A
V100155

Dam
V100145

Sealer




HINT:

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS


PROCEDURE

Hide 56115A 1.INSTALL NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type)

a.
E270663

Install 2 new No. 1 windshield glass stoppers to the vehicle body as shown in the illustration.

NOTICE:

Only 2-piece type windshield glass stoppers are provided as supply parts. Use 2-piece type stoppers as replacements even if 1-piece type stoppers were originally installed.



Hide 56116C 2.INSTALL NO. 2 WINDSHIELD GLASS STOPPER (for 2-piece Type)

a.

Using a brush or sponge, coat the application area of 2 new No. 2 windshield glass stoppers with Primer G.

NOTICE:
·

Do not apply too much Primer G.


·

Allow the Primer G to dry for 3 minutes or more.


·

Throw away any leftover Primer G.



HINT:

If an area other than specified is coated by accident, wipe off the Primer G with a clean piece of cloth before it dries.



b.

Install the 2 No. 2 windshield glass stoppers to the windshield glass as shown in the illustration.

E270664C03
6.333,1.583 6.333,1.135 false 6.25,0.729 6.25,0.427 false 6.5,0.771 6.5,0.604 true 5.385,0.823 5.75,0.5 true 5.958,0.823 5.75,0.5 true 1.5,0.792 1.5,0.625 true 1.25,0.74 1.25,0.438 false 1.333,1.563 1.333,1.146 false 0.375,0.844 0.74,0.521 true 0.958,0.844 0.75,0.521 true 1.198,0.271 1.51,0.427 0.313,0.156 10 false *1 0.688,0.354 1,0.51 0.313,0.156 10 false *b 1.458,0.458 1.771,0.615 0.313,0.156 10 false *c 1.281,1.583 1.594,1.74 0.313,0.156 10 false *d 6.198,0.26 6.51,0.417 0.313,0.156 10 false *1 5.688,0.344 6,0.5 0.313,0.156 10 false *b 6.448,0.417 6.76,0.573 0.313,0.156 10 false *c 6.292,1.604 6.604,1.76 0.313,0.156 10 false *d 1.688,1.177 2,1.333 0.313,0.156 10 false a 6.708,1.167 7.021,1.323 0.313,0.156 10 false a 0.052,0.042 0.365,0.24 0.313,0.198 10 false *a
*1 Windshield Glass - -
*a Back of Windshield Glass *b Ceramic Notch
*c Ceramic Line *d Primer G Application Area


Standard:
Area Specified Condition
a 8.3 mm (0.3268 in.)



Hide 56117A 3.INSTALL WINDOW GLASS ADHESIVE DAM

a.
E270658C03
2.792,3.781 2.542,4.115 false 0.083,0.094 0.396,0.25 0.313,0.156 10 false *a 2.781,3.635 3.094,3.792 0.313,0.156 10 false *b 1.542,1.625 1.854,1.781 0.313,0.156 10 false A 1.542,2.156 1.854,2.313 0.313,0.156 10 false A 0.615,3.688 1.01,3.844 0.396,0.156 10 false A - A 1.552,3.458 1.865,3.615 0.313,0.156 10 false a 2.073,3.458 2.385,3.615 0.313,0.156 10 false b
*a Back of Windshield Glass
*b Ceramic Notch
V100155

Primer G


Using a brush or sponge, coat the application area of a new No. 2 window glass adhesive dam with Primer G.

Standard Dimension:
Area Dimension
a 5.0 mm (0.1969 in.)
b 6.5 mm (0.2559 in.)


NOTICE:
·

Do not apply too much primer.

·

Allow the Primer G to dry for 3 minutes or more.

·

Throw away any leftover primer.



HINT:

If an area other than specified is coated by accident, wipe off the Primer G with a clean piece of cloth before it dries.



b.
E270659C03
2.781,2.781 2.906,2.677 false 0.646,2.771 0.5,2.667 false 2.5,4 2.75,3.75 false 0.063,0.052 0.375,0.208 0.313,0.156 10 false *a 0.333,2.573 0.646,2.729 0.313,0.156 10 false *b 0.823,2.281 1.135,2.438 0.313,0.156 10 false *c 2.938,2.583 3.25,2.74 0.313,0.156 10 false *b 2.469,2.25 2.781,2.406 0.313,0.156 10 false *c 2.063,3.365 2.375,3.521 0.313,0.156 10 false a 2.75,3.625 3.063,3.781 0.313,0.156 10 false *1 1.323,1.667 1.479,1.865 0.156,0.198 10 false A 1.323,2.188 1.479,2.385 0.156,0.198 10 false A 0.625,3.469 1,3.656 0.375,0.188 10 false A - A
*a Back of Windshield Glass
*b Ceramic Notch
*c Ceramic Notch used for Dam Cut Point


Install the window glass adhesive dam to the windshield glass as shown in the illustration.

Standard:
Area Specified Condition
a 6.5 mm (0.2559 in.)



Hide 75533E 4.INSTALL WINDSHIELD OUTSIDE MOULDING

E270661C02
2.688,1.479 3.125,1.656 true 1.917,2.74 2.073,2.938 0.156,0.198 10 false a 1.323,0.135 1.479,0.333 0.156,0.198 10 false A 1.333,0.771 1.49,0.969 0.156,0.198 10 false A 0.823,3.052 1.198,3.25 0.375,0.198 10 false A - A 3.271,1 3.427,1.198 0.156,0.198 10 false b 2.521,1.375 2.833,1.573 0.313,0.198 10 false *b 0.063,0.042 0.375,0.24 0.313,0.198 10 false *a
*a Back of Windshield Glass
*b Primer G Application Area
V100155

Primer G


a.

Using a brush or sponge, coat the application area of a new windshield outside moulding with Primer G.

Standard Dimension:
Area Dimension
a 8.8 mm (0.3465 in.)
b 735.1 mm (28.9409 in.)



b.
E270662C02
0.156,2.802 0.313,3 0.156,0.198 10 false a 3.208,2.802 3.365,3 0.156,0.198 10 false a 0.906,3.552 1.063,3.75 0.156,0.198 10 false b 2.365,3.479 2.521,3.677 0.156,0.198 10 false c 0.094,3.521 0.448,3.729 0.354,0.208 10 false A - A 1.688,3.5 2.042,3.708 0.354,0.208 10 false B - B 1.323,0.146 1.479,0.344 0.156,0.198 10 false A 1.323,0.771 1.479,0.969 0.156,0.198 10 false A 3.229,0.448 3.385,0.646 0.156,0.198 10 false B 2.854,0.531 3.01,0.729 0.156,0.198 10 false B 0.052,0.042 0.365,0.198 0.313,0.156 10 false *a
*a Back of Windshield Glass
V100135

Edge of Curved Surface


Install the windshield outside moulding to the windshield glass as shown in the illustration.

Standard Dimension:
Area Dimension
a +/-5.0 mm (0.1969 in.)
b 5.4 mm (0.2126 in.)
c 14.2 mm (0.5591 in.)



Hide 56111 5.INSTALL WINDSHIELD GLASS

B436256C01
1.76,1.656 2.042,1.906 true 2.073,1.917 2.385,2.115 0.313,0.198 10 false *a
*a Matchmark


a.

Position the windshield glass.

i.

Using suction cups, place the windshield glass in the correct position.


ii.

Check that the entire contact surface of the glass rim is perfectly even.


iii.

Place matchmarks on the windshield glass and vehicle body at the locations indicated in the illustration.

NOTICE:

Check that the stoppers are attached to the vehicle body correctly.



iv.

Using suction cups, remove the windshield glass.



b.
E268577C01
1.833,0.583 2.083,0.75 false 1.917,1.5 2.167,1.667 false 1.708,1.854 2.042,1.771 false 1.667,0.5 1.979,0.656 0.313,0.156 10 *1 2.667,0.479 2.979,0.635 0.313,0.156 10 *a 2.833,1.427 3.146,1.583 0.313,0.156 10 *b 1.76,1.417 2.073,1.573 0.313,0.156 10 *1 1.563,1.781 1.875,1.938 0.313,0.156 10 *2
*1 Primer M
*2 Adhesive
*a CORRECT
*b INCORRECT
V100155

Primer M


Using a brush, apply Primer M to the exposed part of the vehicle body.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Do not apply primer to the adhesive.

·

Throw away any leftover primer.

·

Do not apply too much primer.




c.

Using a brush or sponge, apply Primer G to the contact surface of the glass.

E268578C02
1.917,2.688 1.917,3.188 true 0.073,0.052 0.385,0.208 0.313,0.156 10 false *a 4.792,0.552 5.104,0.708 0.313,0.156 10 false *b 6.521,0.531 6.833,0.688 0.313,0.156 10 false *b 4.375,2.24 4.688,2.396 0.313,0.156 10 false *b 6.51,2.333 6.823,2.49 0.313,0.156 10 false *b 1.865,3.219 2.177,3.375 0.313,0.156 10 false *b 0.833,1.323 1.146,1.479 0.313,0.156 10 false A 0.917,0.635 1.229,0.792 0.313,0.156 10 false A 1.677,0.708 1.99,0.865 0.313,0.156 10 false B 1.677,1.406 1.99,1.563 0.313,0.156 10 false B 0.292,1.313 0.604,1.469 0.313,0.156 10 false C 0.958,1.469 1.271,1.625 0.313,0.156 10 false C 0.896,2.188 1.208,2.344 0.313,0.156 10 false D 0.823,2.865 1.135,3.021 0.313,0.156 10 false D 5.51,0.313 5.896,0.469 0.385,0.156 10 false B - B 3.781,0.323 4.167,0.479 0.385,0.156 10 false A - A 3.781,2 4.167,2.156 0.385,0.156 10 false C - C 5.51,2 5.896,2.156 0.385,0.156 10 false D - D 6.271,2.188 6.583,2.344 0.313,0.156 10 false *b
*a Back of Windshield Glass *b Adhesive Center Line
V100155

Primer G - -


HINT:

If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer.


NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.




d.

Apply adhesive to the windshield glass.

Adhesive:

Toyota Genuine Windshield Glass Adhesive (High modulus Type) or Equivalent


i.

Cut off the tip of the cartridge nozzle as shown in the illustration.

HINT:

After cutting off the tip, use all adhesive within the time written in the table below.


Usage Time Frame:
Temperature Usage Time Frame
35°C (95°F) 15 minutes
20°C (68°F) 1 hour 40 minutes
5°C (41°F) 8 hours



ii.

Load the sealer gun with the cartridge.


iii.

Apply adhesive to the glass as shown in the illustration.

E268579C02
6.125,1.5 6.375,1.25 true 4.417,1.417 4.667,1.167 true 6,3.083 6.083,2.781 true 6,3.083 6.271,2.896 true 4.375,2.969 4.625,3.219 true 0.396,2.938 0.552,3.135 0.156,0.198 10 false b 3.792,0.302 4.208,0.521 0.417,0.219 10 false A - A 5.51,0.323 6.146,0.51 0.635,0.188 10 false B - B 5.521,2 5.958,2.208 0.438,0.208 10 false D - D 3.792,2.01 4.25,2.229 0.458,0.219 10 false C - C 2.76,0.521 2.917,0.719 0.156,0.198 10 false a 3.219,0.75 3.375,0.948 0.156,0.198 10 false b 0.906,0.917 1.063,1.115 0.156,0.198 10 false A 0.823,1.594 0.979,1.792 0.156,0.198 10 false A 1.688,1.01 1.844,1.208 0.156,0.198 10 false B 1.688,1.708 1.844,1.906 0.156,0.198 10 false B 0.313,1.604 0.469,1.802 0.156,0.198 10 false C 0.979,1.75 1.135,1.948 0.156,0.198 10 false C 0.917,2.479 1.073,2.677 0.156,0.198 10 false D 0.844,3.115 1,3.313 0.156,0.198 10 false D 4.26,1.375 4.573,1.573 0.313,0.198 10 false *b 5.979,1.448 6.292,1.646 0.313,0.198 10 false *b 5.906,3.104 6.219,3.302 0.313,0.198 10 false *b 4.667,3.198 4.979,3.396 0.313,0.198 10 false *b 4.792,0.51 4.948,0.708 0.156,0.198 10 false c 6.396,0.583 6.552,0.781 0.156,0.198 10 false d 4.594,2.354 4.75,2.552 0.156,0.198 10 false d 6.219,2.156 6.375,2.354 0.156,0.198 10 false d 6.708,2.677 6.865,2.875 0.156,0.198 10 false c 6.542,2.115 6.698,2.313 0.156,0.198 10 false b 0.063,0.052 0.354,0.24 0.292,0.188 10 false *a 0.854,3.344 1.01,3.542 0.156,0.198 10 false a
*a Back of Windshield Glass *b Adhesive Center Line
V100155

Adhesive - -


Standard:
Area Specified Condition
a 12.0 mm (0.472 in.)
b 8.0 mm (0.315 in.)
c 4.0 mm (0.1575 in.)
d 3.0 mm (0.1181 in.)




e.
B436256C01
1.76,1.656 2.042,1.906 true 2.073,1.917 2.385,2.115 0.313,0.198 10 false *a
*a Matchmark


Install the windshield glass to the vehicle body.

i.

Using suction cups, position the windshield glass so that the matchmarks are aligned. Press it in gently along the rim.


ii.

Lightly press the outer surface of the glass to ensure that it is securely fit to the vehicle body.

NOTICE:
·

Check that the stoppers are attached to the vehicle body correctly.

·

Check that the vehicle body and glass have a small gap between them.




iii.

Hold the windshield glass in place securely with protective tape or equivalent until the adhesive hardens.

NOTICE:

Do not drive the vehicle for the time described in the table below.


Minimum Time:
Temperature Minimum Time prior to Driving Vehicle
35°C (95°F) 1 hour and 30 minutes
20°C (68°F) 5 hours
5°C (41°F) 24 hours




f.
B435755

w/ Heated Windshield Defroster System:

i.

Connect the 2 connectors and lock the connector as shown in the illustration.



Hide 6.CHECK FOR LEAKS AND REPAIR

a.

Conduct a leak test after the adhesive has completely hardened.


b.

Seal any leaks with auto glass sealer.


Hide 55781E 7.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 53867H 8.INSTALL FRONT FENDER TO COWL SIDE SEAL LH

Hide 53866J 9.INSTALL FRONT FENDER TO COWL SIDE SEAL RH

Hide 10.INSTALL WINDSHIELD WIPER ARM AND BLADE ASSEMBLY LH

Hide 11.INSTALL WINDSHIELD WIPER ARM AND BLADE ASSEMBLY RH

Hide 85192 12.INSTALL WINDSHIELD WIPER ARM COVER

Hide 86101Q 13.INSTALL NO. 4 ANTENNA CORD SUB-ASSEMBLY

Hide 63310 14.INSTALL ROOF HEADLINING ASSEMBLY

Hide 74320 16.INSTALL VISOR ASSEMBLY LH

Hide 74310 17.INSTALL VISOR ASSEMBLY RH

Hide 74610A 18.INSTALL ASSIST GRIP SUB-ASSEMBLY

Hide 81260A 19.INSTALL MAP LIGHT ASSEMBLY

Hide 87810 20.INSTALL INNER REAR VIEW MIRROR ASSEMBLY

Hide 8646C 21.INSTALL FORWARD RECOGNITION CAMERA (w/ Pre-crash Safety System)

Hide 62212 22.INSTALL FRONT PILLAR GARNISH LH (w/o Curtain Shield Airbag)

Hide 62211 23.INSTALL FRONT PILLAR GARNISH RH (w/o Curtain Shield Airbag)

Hide 62212 24.INSTALL FRONT PILLAR GARNISH LH (w/ Curtain Shield Airbag)

Hide 62211 25.INSTALL FRONT PILLAR GARNISH RH (w/ Curtain Shield Airbag)

Hide 62312B 26.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Hide 62311B 27.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

Hide 28.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 56111 29.CHECK WINDSHIELD GLASS

a.

Conduct a leak test after the adhesive has completely hardened.


b.

Seal any leaks with auto glass sealer.