Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM(for 2WW) › from 2015.10
RM3090E _51 Engine / Hybrid System _009049 STOP AND START _0208733 STOP AND START SYSTEM(for 2WW) J

STOP AND START  STOP AND START SYSTEM(for 2WW)  Starter Signal Circuit  


DESCRIPTION

The engine stop and start ECU can activate the ST relay to operate the starter assembly.

WIRING DIAGRAM

A375866E01
0.083,0.083 4.854,0.323 4.771,0.24 12 false w/ Entry and Start System: 1.76,0.99 2.073,1.188 0.313,0.198 10 false 3A 1.802,0.792 1.958,0.99 0.156,0.198 10 false 1 2.667,1.677 4.042,1.875 1.375,0.198 10 false IG1 NO. 1 1.771,1.417 2.083,1.615 0.313,0.198 10 false 3D 1.813,1.229 1.969,1.427 0.156,0.198 10 false 9 1.771,2.083 2.083,2.281 0.313,0.198 10 false 3B 1.771,1.885 2.083,2.083 0.313,0.198 10 false 14 3.198,2.25 3.656,2.448 0.458,0.198 10 false IGN 4.604,2.083 4.917,2.281 0.313,0.198 10 false 3C 4.615,1.885 4.927,2.083 0.313,0.198 10 false 37 4.604,1.417 4.917,1.615 0.313,0.198 10 false 3C 4.615,1.219 4.927,1.417 0.313,0.198 10 false 43 4.604,0.99 4.917,1.188 0.313,0.198 10 false 3D 4.604,0.781 4.917,0.979 0.313,0.198 10 false 43 3.646,1.135 4.563,1.333 0.917,0.198 10 false EPS-IG 5.719,1 6.177,1.198 0.458,0.198 10 false G87 5.75,0.792 6.063,0.99 0.313,0.198 10 false 17 6.115,1 6.573,1.198 0.458,0.198 10 false IG1 0.219,2.208 0.375,2.406 0.156,0.198 10 false B 5.719,2.094 6.177,2.292 0.458,0.198 10 false G87 5.75,1.885 6.063,2.083 0.313,0.198 10 false 20 6.094,2.083 6.552,2.281 0.458,0.198 10 false IG2 1.844,2.688 4.542,2.927 2.698,0.24 10 false Instrument Panel Junction Block Assembly 1.396,3.531 1.854,3.729 0.458,0.198 10 false IG2 1.26,3.125 1.417,3.323 0.156,0.198 10 false 2 1.26,3.938 1.417,4.135 0.156,0.198 10 false 1 0.646,3.135 0.802,3.333 0.156,0.198 10 false 5 0.646,3.927 0.802,4.125 0.156,0.198 10 false 3 3.396,3.167 3.552,3.365 0.156,0.198 10 false 5 4.24,3.188 4.396,3.385 0.156,0.198 10 false 3 3.396,3.594 3.552,3.792 0.156,0.198 10 false 2 4.24,3.625 4.396,3.823 0.156,0.198 10 false 1 3.385,4.146 4.448,4.344 1.063,0.198 10 false EFI-MAIN NO. 1 4.573,3.5 5.302,3.729 0.729,0.229 10 false EFI NO. 1 2.167,4.375 3.229,4.573 1.063,0.198 10 false EFI-MAIN NO. 1 5.708,3.323 6.167,3.521 0.458,0.198 10 false A66 5.781,3.115 5.938,3.313 0.156,0.198 10 false 1 6.115,3.302 6.427,3.5 0.313,0.198 10 false +B 4.646,4.635 4.802,4.833 0.156,0.198 10 false D 2.219,5.323 2.833,5.521 0.615,0.198 10 false IG1D 2.688,5.344 3.146,5.542 0.458,0.198 10 false G84 2.75,5.135 2.906,5.333 0.156,0.198 10 false 6 1.823,6.365 2.438,6.563 0.615,0.198 10 false IG2D 1.438,6.354 1.896,6.552 0.458,0.198 10 false G82 0.49,6.51 0.948,6.708 0.458,0.198 10 false IG2 0.646,7.708 1.104,7.906 0.458,0.198 10 false AM2 1.833,7.552 2.146,7.75 0.313,0.198 10 false +B 0.198,8.073 0.354,8.271 0.156,0.198 10 false A 1.406,7.927 2.958,8.5 1.552,0.573 10 false Certification ECU (Smart Key ECU Assembly) 1.427,7.563 1.885,7.76 0.458,0.198 10 false G82 2.677,6.719 3.135,6.917 0.458,0.198 10 false G82 2.677,7.49 3.135,7.688 0.458,0.198 10 false G82 2.177,6.708 2.792,6.906 0.615,0.198 10 false STAR 2.271,7.469 2.729,7.667 0.458,0.198 10 false STA 2.771,6.479 2.927,6.677 0.156,0.198 10 false 5 2.75,7.271 2.906,7.469 0.156,0.198 10 false 7 1.51,7.344 1.667,7.542 0.156,0.198 10 false 2 1.521,6.146 1.677,6.344 0.156,0.198 10 false 9 6.104,6.719 6.563,6.917 0.458,0.198 10 false STA 6.104,5.677 6.563,5.875 0.458,0.198 10 false CLL 5.708,5.677 6.167,5.875 0.458,0.198 10 false A66 5.708,6.708 6.167,6.906 0.458,0.198 10 false A66 5.75,6.5 6.063,6.698 0.313,0.198 10 false 21 5.75,5.469 6.063,5.667 0.313,0.198 10 false 17 4.948,7.292 5.104,7.49 0.156,0.198 10 false C 3.479,7 4.333,7.198 0.854,0.198 10 false A4*1, F2*2 3.479,7.188 4.781,7.615 1.302,0.427 10 false Clutch Start Switch Assembly (for Lower) 3.49,6.583 3.646,6.781 0.156,0.198 10 false 2 4.448,6.583 4.604,6.781 0.156,0.198 10 false 1 5.406,7.375 7.104,7.646 1.698,0.271 10 false Engine Stop and Start ECU 3.573,8.313 5.26,8.51 1.688,0.198 10 false *1: for LHD 4.885,8.313 6.573,8.51 1.688,0.198 10 false *2: for RHD

A375867E01
0.073,0.073 5.031,0.313 4.958,0.24 12 false w/o Entry and Start System: 1.771,0.99 2.083,1.188 0.313,0.198 10 false 3A 1.802,0.781 1.958,0.979 0.156,0.198 10 false 1 1.781,1.417 2.094,1.615 0.313,0.198 10 false 3D 1.813,1.229 1.969,1.427 0.156,0.198 10 false 9 1.781,2.417 2.094,2.615 0.313,0.198 10 false 3B 1.781,2.219 2.094,2.417 0.313,0.198 10 false 14 2.677,1.677 4.052,1.875 1.375,0.198 10 false IG1 NO. 1 3.625,1.177 4.542,1.375 0.917,0.198 10 false EPS-IG 4.604,0.99 4.917,1.188 0.313,0.198 10 false 3D 4.604,0.781 4.917,0.979 0.313,0.198 10 false 43 4.615,1.406 4.927,1.604 0.313,0.198 10 false 3C 4.615,1.208 4.927,1.406 0.313,0.198 10 false 43 4.604,1.958 4.917,2.156 0.313,0.198 10 false 3C 4.604,1.75 4.917,1.948 0.313,0.198 10 false 48 2.948,2.115 3.406,2.313 0.458,0.198 10 false AM1 4.594,2.427 4.906,2.625 0.313,0.198 10 false 3C 4.594,2.208 4.906,2.406 0.313,0.198 10 false 37 3.198,2.563 3.656,2.76 0.458,0.198 10 false IGN 0.208,2.26 0.365,2.458 0.156,0.198 10 false B 5.719,0.99 6.177,1.188 0.458,0.198 10 false G87 5.75,0.792 6.063,0.99 0.313,0.198 10 false 21 6.115,0.99 6.573,1.188 0.458,0.198 10 false IG1 1.833,2.854 4.552,3.083 2.719,0.229 10 false Instrument Panel Junction Block Assembly 5.719,2.406 6.177,2.604 0.458,0.198 10 false G87 6.115,2.406 6.573,2.604 0.458,0.198 10 false IG2 5.74,2.198 6.052,2.396 0.313,0.198 10 false 18 1.406,3.542 1.865,3.74 0.458,0.198 10 false IG2 1.292,3.167 1.448,3.365 0.156,0.198 10 false 2 1.281,3.927 1.438,4.125 0.156,0.198 10 false 1 0.656,3.938 0.813,4.135 0.156,0.198 10 false 3 0.635,3.156 0.792,3.354 0.156,0.198 10 false 5 3.49,3.281 3.646,3.479 0.156,0.198 10 false 5 4.302,3.292 4.458,3.49 0.156,0.198 10 false 3 3.49,3.625 3.646,3.823 0.156,0.198 10 false 2 4.302,3.615 4.458,3.813 0.156,0.198 10 false 1 3.417,4.115 4.521,4.313 1.104,0.198 10 false EFI-MAIN NO. 1 2.125,3.938 3.229,4.135 1.104,0.198 10 false EFI-MAIN NO. 1 4.646,4.458 4.802,4.656 0.156,0.198 10 false D 4.615,3.583 5.365,3.823 0.75,0.24 10 false EFI NO. 1 5.719,3.427 6.177,3.625 0.458,0.198 10 false A66 5.781,3.208 5.938,3.406 0.156,0.198 10 false 1 6.104,3.417 6.417,3.615 0.313,0.198 10 false +B 1.677,5.281 2.135,5.479 0.458,0.198 10 false AM1 1.677,5.802 2.135,6 0.458,0.198 10 false AM2 1.427,5.771 1.583,5.969 0.156,0.198 10 false 4 1.427,5.24 1.583,5.438 0.156,0.198 10 false 5 2.844,5.219 3,5.417 0.156,0.198 10 false 8 2.844,5.563 3,5.76 0.156,0.198 10 false 2 2.844,5.813 3,6.01 0.156,0.198 10 false 3 2.448,5.823 2.906,6.021 0.458,0.198 10 false IG2 2.406,5.573 2.865,5.771 0.458,0.198 10 false ST2 2.427,5.25 2.885,5.448 0.458,0.198 10 false IG1 1.427,6.479 1.74,6.677 0.313,0.198 10 false G4 1.448,6.635 2.594,7.188 1.146,0.552 10 false Ignition or Starter Switch Assembly 3.49,6.563 3.646,6.76 0.156,0.198 10 false 2 4.469,6.583 4.625,6.781 0.156,0.198 10 false 1 3.198,7 4,7.198 0.802,0.198 10 false A4*1, F2*2 3.188,7.198 4.51,7.625 1.323,0.427 10 false Clutch Start Switch Assembly (for Lower) 0.583,7.656 1.042,7.854 0.458,0.198 10 false AM2 0.5,6.542 0.958,6.74 0.458,0.198 10 false IG2 6.125,5.688 6.583,5.885 0.458,0.198 10 false CLL 5.729,5.688 6.188,5.885 0.458,0.198 10 false A66 5.719,6.708 6.177,6.906 0.458,0.198 10 false A66 6.104,6.698 6.563,6.896 0.458,0.198 10 false STA 5.76,5.469 6.073,5.667 0.313,0.198 10 false 17 5.75,6.49 6.063,6.688 0.313,0.198 10 false 21 0.208,8.063 0.365,8.26 0.156,0.198 10 false A 4.948,7.292 5.104,7.49 0.156,0.198 10 false C 5.396,7.396 7.104,7.615 1.708,0.219 10 false Engine Stop and Start ECU 1.26,8.333 2.948,8.531 1.688,0.198 10 false *1: for LHD 2.458,8.333 4.146,8.531 1.688,0.198 10 false *2: for RHD

A375868E01
0.292,0.094 0.448,0.292 0.156,0.198 10 false A 0.833,0.094 0.99,0.292 0.156,0.198 10 false B 1,0.573 1.458,0.771 0.458,0.198 10 false ALT 2.021,1.76 2.333,1.958 0.313,0.198 10 false C4 2.063,1.552 2.219,1.75 0.156,0.198 10 false 1 3.458,1.708 3.771,1.906 0.313,0.198 10 false B6 3.479,1.5 3.635,1.698 0.156,0.198 10 false 1 2.302,2.302 3.5,2.51 1.198,0.208 10 false Starter Assembly 5.615,1.125 6.073,1.323 0.458,0.198 10 false A86 5.688,0.927 5.844,1.125 0.156,0.198 10 false 8 6.021,1.125 6.635,1.323 0.615,0.198 10 false GND1 5.677,2.073 5.833,2.271 0.156,0.198 10 false 2 5.615,2.281 6.073,2.479 0.458,0.198 10 false A86 6.021,2.271 6.635,2.469 0.615,0.198 10 false GND2 5.625,3.271 6.083,3.469 0.458,0.198 10 false A66 5.688,3.042 5.844,3.24 0.156,0.198 10 false 6 6.031,3.271 6.646,3.469 0.615,0.198 10 false DGND 1.51,3.573 1.823,3.771 0.313,0.198 10 false ST 2.49,4.094 2.802,4.292 0.313,0.198 10 false ST 2.135,3.313 2.292,3.51 0.156,0.198 10 false 5 2.958,3.302 3.115,3.5 0.156,0.198 10 false 3 2.125,3.625 2.281,3.823 0.156,0.198 10 false 1 2.948,3.635 3.104,3.833 0.156,0.198 10 false 2 3.823,3.729 3.979,3.927 0.156,0.198 10 false C 4.448,4.823 5.354,5.021 0.906,0.198 10 false BBC 5.625,4.656 6.083,4.854 0.458,0.198 10 false A86 6.021,4.646 6.635,4.844 0.615,0.198 10 false BIN1 5.708,4.438 5.865,4.635 0.156,0.198 10 false 3 4.24,5.438 5.146,5.635 0.906,0.198 10 false BBC NO. 2 5.615,5.281 6.073,5.479 0.458,0.198 10 false A86 5.688,5.052 5.844,5.25 0.156,0.198 10 false 1 6.021,5.25 6.635,5.448 0.615,0.198 10 false BIN2 0.448,5.823 1.521,6.021 1.073,0.198 10 false FL MAIN 0.625,7.302 1.698,7.5 1.073,0.198 10 false Battery 2.354,5.708 2.813,5.906 0.458,0.198 10 false STA 2.771,5.594 3.083,5.792 0.313,0.198 10 false 36 2.26,6.5 2.875,6.698 0.615,0.198 10 false CANH 2.781,6.292 3.094,6.49 0.313,0.198 10 false 26 2.281,6.99 2.896,7.188 0.615,0.198 10 false CANL 2.781,6.813 3.094,7.01 0.313,0.198 10 false 25 2.271,7.375 2.885,7.573 0.615,0.198 10 false MREL 2.802,7.229 2.958,7.427 0.156,0.198 10 false 9 3.385,7.323 3.542,7.521 0.156,0.198 10 false D 5.604,6.5 6.063,6.698 0.458,0.198 10 false G87 5.646,6.302 5.958,6.5 0.313,0.198 10 false 13 6,6.5 6.615,6.698 0.615,0.198 10 false CANH 6,7.01 6.615,7.208 0.615,0.198 10 false CANL 5.604,7 6.063,7.198 0.458,0.198 10 false G87 5.646,6.792 5.958,6.99 0.313,0.198 10 false 14 1.729,7.75 2.188,7.948 0.458,0.198 10 false A62 1.729,7.938 2.188,8.135 0.458,0.198 10 false ECM 0.281,8.469 3.948,8.667 3.667,0.198 10 false : CAN Communication Line 5.385,7.563 7.115,7.792 1.729,0.229 10 false Engine Stop and Start ECU

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>REGISTRATION

·

After replacing the engine stop and start ECU or airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>REGISTRATION

·

After replacing the starter assembly, perform initialization of the number of starter operations stored in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>REGISTRATION

·

When the starter assembly is replaced, "ST relay" must be also replaced.

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK CRANKING
a.

Turn the ignition switch to START and check that the engine cranks.


Result:
Result Proceed to
Engine cranks A
Engine does not crank B



A

2.PERFORM ACTIVE TEST USING GTS (STARTER)

B

5.PERFORM ACTIVE TEST USING GTS (STARTER)
2.PERFORM ACTIVE TEST USING GTS (STARTER)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Active Test / Starter.

Powertrain > Stop and Start > Active Test
Tester Display
Starter
50004 227 7

e.

Check whether the engine cranks while the Active Test "Starter" is being performed.

NOTICE:

The Active Test "Starter" is stopped automatically 3 seconds after the starter assembly begins operating.


Standard:

Engine cranks



Result:
Proceed to
OK
NG



OK

GO TO DTC P1603 (CONFIRM CAUSE OF ENGINE STALL)

NG

3.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU POWER SOURCE CIRCUIT)
3.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU POWER SOURCE CIRCUIT)
A348463C17
0.958,0.5 1.302,0.76 0.344,0.26 3.396,0.5 3.74,0.76 0.344,0.26 5.813,0.51 6.26,0.813 0.448,0.302 0.365,2.073 0.719,1.563 true 0.906,2.052 0.74,1.75 true 2.438,2.094 2.604,1.708 true 5.542,2.063 5.771,1.771 true 6.354,2.052 6.198,1.771 true 0.323,0.115 0.635,0.313 0.313,0.198 10 false *a 1.01,0.552 1.323,0.75 0.313,0.198 10 false A86 3.448,0.563 3.76,0.76 0.313,0.198 10 false A66 5.906,0.583 6.438,0.781 0.531,0.198 10 false G87 0.844,2.104 1.156,2.302 0.313,0.198 10 false BIN1 0.229,2.104 0.542,2.302 0.313,0.198 10 false BIN2 2.323,2.115 2.635,2.313 0.313,0.198 10 false +B 6.292,2.083 6.604,2.281 0.313,0.198 10 false IG1 5.427,2.094 5.74,2.292 0.313,0.198 10 false IG2
*a Front view of wire harness connector
(to Engine Stop and Start ECU)
- -


a.

Disconnect the engine stop and start ECU connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A86-1 (BIN2) - Body ground Always 9.5 to 14 V
A86-3 (BIN1) - Body ground Always 9.5 to 14 V



c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A66-1 (+B) - Body ground Ignition switch ON 9.5 to 14 V
G87-18 (IG2) - Body ground Ignition switch ON 9.5 to 14 V
G87-21 (IG1) - Body ground Ignition switch ON 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BODY GROUND)
a.

Disconnect the A86 and A66 engine stop and start ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A86-2 (GND2) - Body ground Always Below 1 Ω
A86-8 (GND1) - Body ground Always Below 1 Ω
A66-6 (DGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.PERFORM ACTIVE TEST USING GTS (STARTER)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Active Test / Starter.

Powertrain > Stop and Start > Active Test
Tester Display
Starter
50004 227 7

e.

Check whether the engine cranks while the Active Test "Starter" is being performed.

NOTICE:

The Active Test "Starter" is stopped automatically 3 seconds after the starter assembly begins operating.


Standard:

Engine cranks



Result:
Result Proceed to
Engine cranks A
Engine does not crank B



A

6.READ VALUE USING GTS (CLUTCH LOWER SW)

B

15.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)
6.READ VALUE USING GTS (CLUTCH LOWER SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Data List / Clutch Lower SW


e.

In accordance with the display on the GTS, read the Data List.

Powertrain > Stop and Start > Data List
Tester Display
Clutch Lower SW
50003 227 11
OK:
Tester Display Condition Normal Condition
Clutch Lower SW Fully Depressed ON
Fully Released OFF



Result:
Result Proceed to
Data Monitor display is not within standards A
Data Monitor display is within standards (w/o Entry and Start System) B
Data Monitor display is within standards (w/ Entry and Start System) C



A

7.INSPECT CLUTCH START SWITCH ASSEMBLY (FOR LOWER)

B

10.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

C

13.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE STOP AND START ECU)
7.INSPECT CLUTCH START SWITCH ASSEMBLY (FOR LOWER)
a.

Inspect the clutch start switch assembly (for lower).

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Result Proceed to
OK (w/o Smart Entry and Start System) A
OK (w/ Smart Entry and Start System) B
NG C



A

8.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - ST RELAY)

B

9.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST RELAY)

C

REPLACE CLUTCH START SWITCH ASSEMBLY (FOR LOWER)

8.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - ST RELAY)
a.

Disconnect the A66 engine stop and start ECU connectors.


b.

Disconnect the G4 ignition or starter switch assembly connector.


c.

Remove the ST relay from the No. 2 engine room relay block and junction block assembly.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G4-2 (ST2) - ST relay terminal 2 Fully Depressed Below 1 Ω
Fully Released 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST RELAY)
a.

Disconnect the G82 certification ECU (smart key ECU assembly) connector.


b.

Remove the ST relay from the No. 2 engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G82-5 (STAR) - ST relay terminal 2 Fully Depressed Below 1 Ω
Fully Released 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition or starter switch assembly.

Click hereEngine / Hybrid System>2WW STARTING>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - BATTERY)

NG

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY

11.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - BATTERY)
a.

Disconnect the G4 ignition or starter switch assembly connector.


b.
A316828C05
0.5,1.083 0.917,1.333 0.417,0.25 2.198,1.063 2.635,0.708 true 0.24,0.156 0.552,0.354 0.313,0.198 10 false *a 2.708,0.615 3.021,0.813 0.313,0.198 10 false AM2 0.594,1.135 0.906,1.333 0.313,0.198 10 false G4
*a Front view of wire harness connector
(to Ignition or Starter Switch Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G4-4 (AM2) - Body ground Always 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY (FOR LOWER))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY (FOR LOWER))
a.

Disconnect the G4 ignition or starter switch assembly connector.


b.

Disconnect the A66 engine stop and start ECU connector.


c.

Disconnect the A4*1 or F2*2 clutch start switch assembly (for lower) connector.

*1: for LHD

*2: for RHD



d.

Disconnect the A62 ECM connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
G4-2 (ST2) - A4-2 Always Below 1 Ω
G4-2 (ST2) - Body ground Always 10 kΩ or higher
A4-2 - Body ground Always 10 kΩ or higher
A66-17 (CLL) - Body ground Always 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition
G4-2 (ST2) - F2-2 Always Below 1 Ω
G4-2 (ST2) - Body ground Always 10 kΩ or higher
F2-2 - Body ground Always 10 kΩ or higher
A66-17 (CLL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE STOP AND START ECU)
a.

Disconnect the G82 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A66 engine stop and start ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G82-5 (STAR) - A66-17 (CLL) Always Below 1 Ω
G82-5 (STAR) - Body ground Always 10 kΩ or higher
A66-17 (CLL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (STAR SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (STAR SIGNAL)
a.
A342958C23
0.083,0.75 0.438,1.052 0.354,0.302 1.021,1.99 1.281,1.781 true 0.24,0.146 0.552,0.344 0.313,0.198 10 false *a 0.135,0.813 0.594,1.01 0.458,0.198 10 false A66 0.771,1.979 1.229,2.177 0.458,0.198 10 false CLL
*a Front view of wire harness connector
(to Engine Stop and Start ECU)


Disconnect the engine stop and start ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A66-17 (CLL) - Body ground Engine started using push start switch assembly (ignition switch turned START) 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

15.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)
a.

Remove the ST relay from the No. 2 engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST relay terminal 2 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST RELAY)
a.

w/ Entry and Start System:

Disconnect the G82 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A66 engine stop and start ECU connector.


c.

Remove the ST relay from the No. 2 engine room relay block and junction block assembly.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A66-21 (STA) - ST relay terminal 2 Always Below 1 Ω
A66-21 (STA) - Body ground Always 10 kΩ or higher
ST relay terminal 2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

17.INSPECT STARTER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.INSPECT STARTER ASSEMBLY
a.

Inspect the starter assembly.

Click hereEngine / Hybrid System>2WW STARTING>STARTER>INSPECTION


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE STARTER ASSEMBLY