Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM(for 2WW) › from 2015.10
RM3090E _51 Engine / Hybrid System _009049 STOP AND START _0208733 STOP AND START SYSTEM(for 2WW) C

STOP AND START  STOP AND START SYSTEM(for 2WW)  P1603  Engine Stall History  


DESCRIPTION

If the engine stalls or fails to start while stop and start control is operating, DTC P1603 will be stored. Using the GTS, the freeze frame data recorded the moment the DTC is stored can be read. Serviceability has been enhanced by enabling the cause of an engine stall or engine start failure which occurred while stop and start control was operating to be checked using the freeze frame data.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P1603 Engine Stall History
Both of the following conditions are met for 0.5 seconds or more (1 trip detection logic):
·

Engine stopped by stop and start control and engine hood opened*1

·

Engine hood courtesy switch (hood lock assembly):

Engine hood opened and mode changed to "stalled"*2


Both of the following conditions are met for 0.5 seconds or more (1 trip detection logic):
·

Engine stopped by stop and start control and collision or low battery voltage detected

·

Collision detection signal received from the airbag sensor assembly and mode changed to "stalled"*2


Both of the following conditions are met for 0.5 seconds or more (1 trip detection logic):
·

Engine being restarted by stop and start control and collision detected

·

Collision detection signal received from the center airbag sensor assembly and mode changed to "stalled"*2


Both of the following conditions are met for 0.5 seconds or more (1 trip detection logic):
·

Engine being restarted by stop and start control and restart fails

·

Using the NE signal, complete combustion is identified 0.6 seconds after the engine stop judgment*3 was made or complete combustion does not occur even after the starter assembly has operated for a certain amount of time (NE signal is normal).


Both of the following conditions are met for 0.5 seconds or more (1 trip detection logic):
·

Engine being restarted by stop and start control and restart fails

·

Engine speed signal from the ECM not received via CAN communication (NE signal is abnormal*4).


Detection Conditions: Always
Sensors/components used for detection: engine hood courtesy switch (hood lock assembly), neutral position sensor (neutral position switch), center airbag sensor assembly, battery, crank position sensor, STA signal circuit, ECM
·

Wire harness or connector

·

Engine hood courtesy switch (hood lock assembly)

·

CAN communication system

·

Vehicle stability control system

·

ECD system

·

Starter assembly

·

Engine stop and start ECU


Does not come on DTC stored

*1: Driving shift position only

*2: The mode "stalled" represents a state in which engine restart is prohibited/canceled due to a collision being detected or the engine hood being opened and restart is not preferable. In this situation, "IG" is displayed for the Data List item [Stop&Start of Eng State]. If the mode changes to "IG", engine start by stop and start control is prohibited and the engine can only be started by operating the ignition or starter switch assembly (w/o Entry and Start System) or push start switch (w/ Entry and Start System).

*3: Engine stop judgment is performed to judge whether the engine is stopped completely. The engine stop and start ECU judges that the engine is stopped when it does not receive an engine speed signal (NE signal) from the ECM for 0.6 seconds or more.

*4: The engine stop and start ECU stores DTC P0335.


CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU (See page TS-26).

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>REGISTRATION

·

After replacing the starter assembly, perform initialization of the number of starter operations stored in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>REGISTRATION

·

When the starter assembly is replaced, "ST relay" must be also replaced.

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>REGISTRATION

·

After replacing the engine stop and start ECU or airbag sensor assembly, perform deceleration sensor zero point clear and calibration.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>REGISTRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

If other DTCs are output, perform troubleshooting for this DTC first.

·

Unlike other DTCs that are stored due to a malfunction in parts, circuits or systems, DTC P1603 allows determination of a malfunctioning part according to problem symptoms and the freeze frame data related to a problem recognized by the customer. As this DTC may be stored due to an operation by the customer, it is not necessary to service the vehicle unless the customer recognized a problem. Clear DTCs and return the vehicle to the customer.

·

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>FREEZE FRAME DATA

·

Stop and Start Control Mode Transition:

A310520E08
0.427,1.563 1.844,2.156 1.417,0.594 10 false Driving status: Normal (engine runs and idles normally) 5.208,1.573 6.833,2.094 1.625,0.521 10 false Stop status: Engine stopped by stop and start control 2.813,0.25 4.156,0.615 1.344,0.365 10 false Stop request: Engine stop requested 2.844,1.5 4.208,1.833 1.365,0.333 10 false Start request: Engine start requested 2.885,2.76 4.094,3.115 1.208,0.354 10 false Engine stall status: Engine stopped 2.229,0.292 2.542,0.49 0.313,0.198 10 false *1 4.604,2.792 4.917,2.99 0.313,0.198 10 false *6 2.25,1.5 2.563,1.698 0.313,0.198 10 false *5 2.25,2.5 2.563,2.698 0.313,0.198 10 false *7 2.25,3.042 2.563,3.24 0.313,0.198 10 false *8 4.583,0.281 4.896,0.479 0.313,0.198 10 false *2 4.604,1.51 4.917,1.708 0.313,0.198 10 false *4 3.646,1.094 3.958,1.292 0.313,0.198 10 false *3 3.656,2.333 3.969,2.531 0.313,0.198 10 false *6

*1: Engine stop conditions are met.

*2: Engine stop judgment is determined.

*3: Engine start conditions are met before the engine is judged as stopped.

*4: Engine start conditions are met.

*5: Engine determined to be started (engine speed reaches a specified rpm).

*6: Collision detected or engine hood opened and mode changed to "stalled".

*7: 0.6 seconds elapse after engine stop judgment is established.

*8: Engine is started using the ignition or starter switch assembly (w/o Entry and Start System) or push start switch assembly (w/ Entry and Start System).




PROCEDURE

1.CHECK DTC OUTPUT (ECD SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes


e.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 61
Result:
Result Proceed to
No ECD system DTCs are output A
Starter assembly does not operate
Starter assembly operates B
ECD system DTCs are output C




A

2.CHECK FREEZE FRAME DATA

B

C

GO TO DIAGNOSTIC TROUBLE CODE CHART (ECD SYSTEM)

2.CHECK FREEZE FRAME DATA
NOTICE:

The freeze frame data is cleared when DTCs are cleared. Be sure to make a note of necessary data in advance.


HINT:

Using the time-series freeze frame data, confirm the freeze frame data recorded the moment the DTC was stored and after the DTC was stored. This information can be useful when troubleshooting.


a.

According to the prompts on the GTS screen, read the time-series freeze frame data to confirm the vehicle conditions when an engine stall occurred while the stop and start control was operating.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>FREEZE FRAME DATA


b.

Check the freeze frame data for engine stall history and engine start failure.

Result:
Tester Display Result Proceed to
Engine Stall History during S&S (Hood Open) Yes A
Engine Stall History during S&S (Collision or Battery Voltage Low) Yes B
Engine Stall History during Engine Starting (Collision) Yes
Engine Start Fail Yes C




A

3.READ VALUE USING GTS (HOOD COURTESY SWITCH)

B

4.CHECK VEHICLE CONDITION (COLLISION HISTORY)

C

8.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ECM - ST RELAY)
3.READ VALUE USING GTS (HOOD COURTESY SWITCH)
NOTICE:

Before performing this step, check that the engine hood can be opened by pulling the hood lock control cable.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Data List / Hood Courtesy Switch.

Powertrain > Stop and Start > Data List
Tester Display
Hood Courtesy Switch
50003 227 8

e.

Read the value displayed on the GTS when the engine hood is opened and closed.

OK:
Tester Display Condition Normal Condition
Hood Courtesy Switch Normal Condition ON
Engine hood is open OFF



Result:
Proceed to
OK
NG



OK

NG

5.INSPECT ENGINE HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY)
4.CHECK VEHICLE CONDITION (COLLISION HISTORY)
a.

Check if the vehicle was in a collision when the engine stalled.

Result:
Result Proceed to
Vehicle was in collision when engine stalled A
Vehicle was not in collision when engine stalled B


HINT:

When "Engine Stall History during S&S (Collision or Battery Low)" or "Engine Stall History during Engine Starting (Collision)" is stored:

This may have been stored because the vehicle was in a collision or a collision detection signal was input while stop and start control was operating.




A

END (ENGINE STALLED BECAUSE COLLISION DETECTION SIGNAL WAS RECEIVED)

B

5.INSPECT ENGINE HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY)
a.

Remove the engine hood courtesy switch (hood lock assembly).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE HOOD COURTESY SWITCH>REMOVAL


b.

Inspect the engine hood courtesy switch (hood lock assembly).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE HOOD COURTESY SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (ENGINE HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY) - BODY GROUND)

NG

6.CHECK HARNESS AND CONNECTOR (ENGINE HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY) - BODY GROUND)
a.

Disconnect the A59 engine hood courtesy switch (hood lock assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A59-1 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ENGINE HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ENGINE HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY))
a.

Disconnect the A66 engine stop and start ECU connector.


b.

Disconnect the A59 engine hood courtesy switch (hood lock assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A66-7 (BNT1) - A59-2 (+) Always Below 1 Ω
A66-7 (BNT1) - Body ground Always 10 kΩ or higher
A59-2 (+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ECM - ST RELAY)
a.

Disconnect the A66 engine stop and start ECU connector.


b.

Disconnect the A62 ECM connector.


c.

Remove the ST relay from the No. 2 engine room relay block and junction block assembly.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A66-21 (STA) - ST relay terminal 2 Always Below 1 Ω
A62-29 (STA) - ST relay terminal 2 Always Below 1 Ω
A66-21 (STA) - A62-29 (STA) Always Below 1 Ω
A66-21 (STA) - Body ground Always 10 kΩ or higher
A62-29 (STA) - Body ground Always 10 kΩ or higher
ST relay terminal 2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)
a.

Remove the ST relay from the No. 2 engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST relay terminal 1 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (ST RELAY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (ST RELAY - BATTERY)
a.

Remove the ST relay from the No. 2 engine room relay block and junction block assembly.


b.
A375353C01
0.146,0.115 0.458,0.313 0.313,0.198 10 false *1 0.333,1.729 0.646,1.927 0.313,0.198 10 false *a
*1 No. 2 Engine Room Relay Block and Junction Block Assembly
*a ST Relay Terminal


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
ST relay terminal 5 - Body ground Always 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - BATTERY)
a.
A317747C02
1.708,0.615 1.25,0.333 1.25,0.333 1.083,0.333 true 0.104,0.094 0.417,0.292 0.313,0.198 10 false *1 0.875,0.25 1.188,0.448 0.313,0.198 10 false *a
*1 Starter Assembly
*a C4-1 Terminal


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C4-1 - Body ground Always 9.5 to 14 V


NOTICE:

Before performing this step, check that the starter assembly connector C4 is not disconnected or loose.



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (ST RELAY - STARTER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (ST RELAY - STARTER ASSEMBLY)
a.

Remove the ST relay from the No. 2 engine room relay block and junction block assembly.


b.

Disconnect the B6 starter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST relay terminal 3 - B6-1 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

13.INSPECT RELAY (ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.INSPECT RELAY (ST RELAY)

Result:
Proceed to
OK
NG



OK

14.INSPECT STARTER ASSEMBLY

NG

REPLACE RELAY (ST RELAY)

14.INSPECT STARTER ASSEMBLY
a.

Inspect the starter assembly.

Click hereEngine / Hybrid System>2WW STARTING>STARTER>INSPECTION


Result:
Proceed to
OK
NG



OK

NG

REPLACE STARTER ASSEMBLY