Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) › from 2015.10
RM3090E _57 Power Source / Network _008434 NETWORKING _0221948 CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) C

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)  U0235  Lost Communication with Cruise Control Front Distance Range Sensor  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
U0235 Lost Communication with Cruise Control Front Distance Range Sensor There is no communication from the millimeter wave radar sensor assembly.
·

Power source circuit of millimeter wave radar sensor assembly

·

Millimeter wave radar sensor assembly CAN main wire or connector

·

Millimeter wave radar sensor assembly


Driving support ECU assembly

WIRING DIAGRAM

C334648E01
5.135,3.938 7.021,4.406 1.885,0.469 10 false Millimeter Wave Radar Sensor Assembly 5.125,3.771 5.438,3.969 0.313,0.198 10 false Z6 5.594,0.458 6.208,0.656 0.615,0.198 10 false CA1P 5.615,1.333 6.177,1.615 0.563,0.281 10 false CA1N 5.615,2.021 6.229,2.219 0.615,0.198 10 false IGB 5.615,3.167 6.229,3.365 0.615,0.198 10 false SGND 5.344,0.448 5.5,0.646 0.156,0.198 10 false 5 5.354,1.031 5.51,1.229 0.156,0.198 10 false 6 5.354,1.854 5.51,2.052 0.156,0.198 10 false 8 5.365,3.01 5.521,3.208 0.156,0.198 10 false 1 3.927,1.823 4.896,2.042 0.969,0.219 10 false ECU-IG NO.3 1.688,0.469 1.979,0.698 0.292,0.229 10 false 7 1.677,1.021 2.052,1.271 0.375,0.25 10 false 18 0.156,1.385 0.573,1.604 0.417,0.219 10 false G173 0.156,1.583 2.188,1.802 2.031,0.219 10 false No. 8 CAN Junction Connector 1.156,2.698 3.385,2.938 2.229,0.24 10 false from Engine Stop and Start ECU*2 1.844,2.021 3.344,2.271 1.5,0.25 10 false from IG1 NO.2 Relay*1 3.792,2.125 4.063,2.375 0.271,0.25 10 false *1 3.781,2.823 4.052,3.073 0.271,0.25 10 false *2 0.146,3.729 2.375,3.969 2.229,0.24 10 false *1: w/o Stop and Start System 0.167,4.135 2.396,4.375 2.229,0.24 10 false *2: w/ Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 20 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220
HINT:

If DTC U1002 is output from gateway of the driving support ECU assembly, this indicates a local bus malfunction. Troubleshoot for DTC U1002 and check for malfunctions in local bus.



Result:
Result Proceed to
DTC U1002 is not output from driving support ECU assembly A
DTC U1002 is output from driving support ECU assembly B



A

2.CHECK FOR OPEN IN CAN BUS WIRE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY CAN MAIN WIRE)

B

GO TO GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

2.CHECK FOR OPEN IN CAN BUS WIRE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY CAN MAIN WIRE)
a.
C333439C31
1.49,0.135 1.979,0.354 0.49,0.219 1.458,1.208 0.906,1.542 0.906,1.542 0.771,1.542 true 1.677,1.229 1.198,1.938 1.198,1.938 1.063,1.938 true 0.073,0.094 0.385,0.25 0.313,0.156 10 false *a 1.656,0.167 2.156,0.469 0.5,0.302 10 false Z6 0.365,1.406 0.979,1.604 0.615,0.198 10 false CA1P 0.646,1.823 1.26,2.021 0.615,0.198 10 false CA1N
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the millimeter wave radar sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Z6-5 (CA1P) - Z6-6 (CA1N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result Proceed to
OK (w/o Stop and Start System) A
OK (w/ Stop and Start System) B
NG C



A

3.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BATTERY AND BODY GROUND)

B

4.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BATTERY AND BODY GROUND)

C

REPAIR OR REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY CAN MAIN WIRE OR CONNECTOR (CA1P, CA1N)

3.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BATTERY AND BODY GROUND)
a.
C333439C32
1.51,0.156 2,0.375 0.49,0.219 1.958,1.229 2.396,1.76 2.396,1.76 2.583,1.76 true 1.479,1.042 1.031,0.583 1.031,0.583 0.896,0.583 true 0.073,0.094 0.385,0.25 0.313,0.156 10 false *a 1.656,0.177 2.052,0.51 0.396,0.333 10 false Z6 2.625,1.656 3.052,1.917 0.427,0.26 10 false IGB 0.458,0.5 0.948,0.75 0.49,0.25 10 false SGND
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Z6-8 (IGB) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Z6-1 (SGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BATTERY AND BODY GROUND)
a.
C333439C32
1.51,0.156 2,0.375 0.49,0.219 1.958,1.229 2.396,1.76 2.396,1.76 2.583,1.76 true 1.479,1.042 1.031,0.583 1.031,0.583 0.896,0.583 true 0.073,0.094 0.385,0.25 0.313,0.156 10 false *a 1.656,0.177 2.052,0.51 0.396,0.333 10 false Z6 2.625,1.656 3.052,1.917 0.427,0.26 10 false IGB 0.458,0.5 0.948,0.75 0.49,0.25 10 false SGND
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Z6-8 (IGB) - Body ground Ignition switch ON 10.5 to 16 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Z6-1 (SGND) - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK A
NG (IGB terminal) B
NG (SGND terminal) C



A

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR