Home › Vehicle Exterior › DOOR / HATCH › BACK DOOR CLOSER SYSTEM › from 2015.10
RM3090E _59 Vehicle Exterior _008794 DOOR / HATCH _0050373 BACK DOOR CLOSER SYSTEM J

DOOR / HATCH  BACK DOOR CLOSER SYSTEM  Back Door Closer does not Operate  


DESCRIPTION

When the back door closer does not operate, one of the following may be the cause: 1) improper fit of the back door, or a foreign object is stuck in the back door, 2) a malfunction in the multiplex network door ECU power source circuit, 3) a malfunction in the back door lock assembly circuit, or 4) a malfunction in the multiplex network door ECU.

WIRING DIAGRAM

B427383E02
1.188,0.458 2.865,0.844 1.677,0.385 10 false from IG1 NO.1 Relay 1.677,0.917 3.354,1.302 1.677,0.385 10 false from Battery 3.875,0.635 5.552,1.021 1.677,0.385 10 false ECU-IG NO.2 3.917,1.094 5.594,1.479 1.677,0.385 10 false ECU-B NO.1 4.104,1.604 4.688,1.927 0.583,0.323 10 false PBD 6.146,0.49 6.719,0.76 0.573,0.271 10 false IG 6.125,0.948 6.698,1.219 0.573,0.271 10 false ECUB 6.094,1.438 6.667,1.708 0.573,0.271 10 false B 6.094,1.938 6.667,2.208 0.573,0.271 10 false DC+ 2.167,1.823 2.74,2.094 0.573,0.271 10 false M+ 6.094,2.396 6.667,2.667 0.573,0.271 10 false DC- 2.167,2.323 2.74,2.594 0.573,0.271 10 false M- 6.104,2.833 6.677,3.104 0.573,0.271 10 false PAWL 2.063,2.729 2.635,3 0.573,0.271 10 false FSW 6.104,3.354 6.677,3.625 0.573,0.271 10 false HAF 2.115,3.25 2.688,3.521 0.573,0.271 10 false CLS 6.115,3.844 6.688,4.115 0.573,0.271 10 false POS 2.083,3.708 2.656,3.979 0.573,0.271 10 false OPN 2.104,4.26 2.677,4.531 0.573,0.271 10 false CTY 6.104,4.344 6.677,4.615 0.573,0.271 10 false FUL 0.542,2.156 2.198,2.375 1.656,0.219 10 false Back Door Lock Motor 0.771,3.021 1.854,3.323 1.083,0.302 10 false Pawl Switch 0.792,3.5 1.875,3.802 1.083,0.302 10 false Latch Switch 0.792,4 1.875,4.302 1.083,0.302 10 false Sector Switch 0.604,4.49 2.833,4.969 2.229,0.479 10 false Back Door Courtesy Switch 2.281,4.74 2.854,5.01 0.573,0.271 10 false E 4.563,4.938 5.135,5.208 0.573,0.271 10 false BCTY 6.094,4.854 6.667,5.125 0.573,0.271 10 false GND 4.604,7.313 5.281,7.583 0.677,0.271 10 false BDSU*2 2.656,6.135 3.229,6.406 0.573,0.271 10 false TSW5 1.531,7.344 2.104,7.615 0.573,0.271 10 false UL 0.573,7.333 1.146,7.604 0.573,0.271 10 false E 0.406,7.729 2.885,8.042 2.479,0.313 10 false Back Door Opener Switch Assembly 0.219,5.26 2.698,5.573 2.479,0.313 10 false Back Door Lock Assembly 3.865,7.656 5.5,8.125 1.635,0.469 10 false Main Body ECU (Multiplex Network Body ECU) 5.823,7.677 6.958,8.302 1.135,0.625 10 false Multiplex Network Door ECU 0.885,8.365 3.365,8.677 2.479,0.313 10 false : CAN Communication Line 2.292,6.677 4.438,7.156 2.146,0.479 10 false Certification ECU (Smart Key ECU Assembly)*1 2.927,8.427 4.969,8.719 2.042,0.292 10 false *1: w/ Entry and Start System 5.219,8.417 7.156,8.698 1.938,0.281 10 false *2: w/o Entry and Start System 5.792,0.313 6.365,0.583 0.573,0.271 10 false 18 5.802,0.771 6.375,1.042 0.573,0.271 10 false 20 5.76,1.427 7.156,1.719 1.396,0.292 10 false U30 5.76,0.49 7.156,0.813 1.396,0.323 10 false U29 5.823,1.229 6.396,1.5 0.573,0.271 10 false 1 5.833,1.75 6.406,2.021 0.573,0.271 10 false 4 5.833,2.25 6.406,2.521 0.573,0.271 10 false 3 5.833,3.125 6.406,3.396 0.573,0.271 10 false 9 5.823,3.646 6.396,3.917 0.573,0.271 10 false 7 5.802,2.635 6.375,2.906 0.573,0.271 10 false 13 5.781,4.167 6.354,4.438 0.573,0.271 10 false 11 5.802,4.667 6.375,4.938 0.573,0.271 10 false 10 4.281,4.75 4.854,5.021 0.573,0.271 10 false 20 4.302,4.927 4.875,5.198 0.573,0.271 10 false A 3.75,4.75 4.323,5.021 0.573,0.271 10 false 33 3.75,4.927 4.323,5.198 0.573,0.271 10 false 3E 2.542,1.771 3.115,2.042 0.573,0.271 10 false 2 2.542,2.26 3.115,2.531 0.573,0.271 10 false 1 2.469,2.833 7.156,3.125 4.688,0.292 10 false U27 2.542,2.677 3.115,2.948 0.573,0.271 10 false 2 2.542,3.156 3.115,3.427 0.573,0.271 10 false 3 2.542,3.646 3.115,3.917 0.573,0.271 10 false 6 2.552,4.188 3.125,4.458 0.573,0.271 10 false 4 2.573,4.656 3.146,4.927 0.573,0.271 10 false 1 4.229,7.313 4.802,7.583 0.573,0.271 10 false G78 4.26,7.156 4.833,7.427 0.573,0.271 10 false 23 0.385,7.573 0.958,7.844 0.573,0.271 10 false U7 1.792,7.198 2.365,7.469 0.573,0.271 10 false 3 0.406,7.208 0.979,7.479 0.573,0.271 10 false 2 2.26,6.51 2.833,6.781 0.573,0.271 10 false G83 2.417,5.99 2.99,6.26 0.573,0.271 10 false 27 2.906,5.292 4.51,5.771 1.604,0.479 10 false Instrument Panel Junction Block Assembly 2.469,2.438 7.156,2.729 4.688,0.292 10 false U26 2.469,1.938 7.156,2.229 4.688,0.292 10 false U26 2.469,3.333 7.156,3.625 4.688,0.292 10 false U27 2.469,3.844 7.156,4.135 4.688,0.292 10 false U27 2.469,4.354 7.156,4.646 4.688,0.292 10 false U27 2.469,4.844 7.156,5.135 4.688,0.292 10 false U27 5.76,1.948 7.156,2.24 1.396,0.292 10 false U30 5.76,2.427 7.156,2.719 1.396,0.292 10 false U30 5.76,4.854 7.156,5.146 1.396,0.292 10 false U30 5.76,0.948 7.156,1.271 1.396,0.323 10 false U29 5.76,2.833 7.156,3.156 1.396,0.323 10 false U29 5.76,3.333 7.156,3.656 1.396,0.323 10 false U29 5.76,3.833 7.156,4.156 1.396,0.323 10 false U29 5.76,4.354 7.156,4.677 1.396,0.323 10 false U29

CAUTION / NOTICE / HINT

NOTICE:
·

First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before troubleshooting this problem.

Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR CLOSER SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect fuses for circuits related to this system before performing the following inspection procedure.

·

If the replacement, removal and installation of the multiplex network door ECU or disconnection of the connectors of the multiplex network door ECU has been performed, initialize the power back door system.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>INITIALIZATION

·

Recognition code registration is necessary when replacing the main body ECU (multiplex network body ECU).

·

When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.



PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR CLOSER SYSTEM>DTC CHECK / CLEAR

Body Electrical > Back Door > Trouble Codes
50001 159

Result:
Result Proceed to
DTC is not output A
DTC B2250 is output B
DTC B2251 is output C



A

2.CHECK BACK DOOR LOCK FUNCTION

B

C

2.CHECK BACK DOOR LOCK FUNCTION
a.

Turn the power back door main switch so that it is not pushed.


b.

Check if the back door can be fully closed by hand.


Result:
Result Proceed to
The back door can be closed normally A
The back door cannot be closed normally B



A

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU -BATTERY AND BODY GROUND)

B

IMPROPER FIT OF BACK DOOR, OR A FOREIGN OBJECT IS STUCK IN BACK DOOR

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU -BATTERY AND BODY GROUND)
a.
B428860C02
1.521,2.625 1.885,2.865 0.365,0.24 1.552,0.302 1.917,0.542 0.365,0.24 0.417,0.531 0.563,0.531 0.563,0.531 0.844,1.25 true 0.677,4.219 0.823,4.219 0.823,4.219 1.25,3.688 true 2.208,3.479 2.74,3.958 2.74,3.958 2.958,3.958 true 0.219,1.479 0.615,1.25 true 0.135,0.156 0.396,0.417 0.26,0.26 10 false *a 0.25,0.427 0.51,0.688 0.26,0.26 10 false IG 0.042,1.531 0.667,1.938 0.625,0.406 10 false ECUB 0.344,4.104 0.969,4.51 0.625,0.406 10 false GND 2.99,3.865 3.427,4.271 0.438,0.406 10 false B 1.604,0.344 1.958,0.635 0.354,0.292 10 false U29 1.594,2.667 1.948,2.958 0.354,0.292 10 false U30
*a Rear view of wire harness connector
(to Multiplex Network Door ECU)


Disconnect the multiplex network door ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U30-10 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
U29-20 (ECUB) - Body ground Always 11 to 14 V
U30-1 (B) - Body ground Always 11 to 14 V
U29-18 (IG) - Body ground Ignition switch ON 11 to 14 V
U29-18 (IG) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

4.INSPECT BACK DOOR LOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT BACK DOOR LOCK ASSEMBLY
a.

Remove the back door lock assembly.

Click hereVehicle Interior>DOOR LOCK>BACK DOOR LOCK>REMOVAL


b.

Inspect the back door lock assembly.

Click hereVehicle Interior>DOOR LOCK>BACK DOOR LOCK>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK ASSEMBLY - MULTIPLEX NETWORK DOOR ECU AND BODY GROUND)

NG

REPLACE BACK DOOR LOCK ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK ASSEMBLY - MULTIPLEX NETWORK DOOR ECU AND BODY GROUND)
a.

Disconnect the U26 and U27 back door lock assembly connector.


b.

Disconnect the U30 and U29 multiplex network door ECU connectors.


c.

Disconnect the 3E instrument panel junction block assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U26-2 (M+) - U30-4 (DC+) Always Below 1 Ω
U26-1 (M-) - U30-3 (DC-) Always Below 1 Ω
U27-4 (CTY) - U29-11 (FUL) Always Below 1 Ω
U27-4 (CTY) - 3E-33 Always Below 1 Ω
U27-2 (FSW) - U29-13 (PAWL) Always Below 1 Ω
U27-3 (CLS) - U29-9 (HAF) Always Below 1 Ω
U27-6 (OPN) - U29-7 (POS) Always Below 1 Ω
U27-1 (E) - Body ground Always Below 1 Ω
U26-2 (M+) or U30-4 (DC+) - Body ground Always 10 kΩ or higher
U26-1 (M-) or U30-3 (DC-) - Body ground Always 10 kΩ or higher
U27-2 (FSW) or U29-13 (PAWL) - Body ground Always 10 kΩ or higher
U27-4 (CTY) or U29-11 (FUL) - Body ground Always 10 kΩ or higher
U27-4 (CTY) or 3E-33 - Body ground Always 10 kΩ or higher
U27-3 (CLS) or U29-9 (HAF) - Body ground Always 10 kΩ or higher
U27-6 (OPN) or U29-7 (POS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - MULTIPLEX NETWORK DOOR ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - MULTIPLEX NETWORK DOOR ECU)
a.

Disconnect the U29 multiplex network door ECU connector.


b.

Disconnect the U27 back door lock assembly connector.


c.

d.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL

for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-20 - U29-11 (FUL) Always Below 1 Ω
A-20 or U29-11 (FUL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG (for RHD)
NG (for LHD)



OK

7.READ VALUE USING GTS

NG (for RHD)

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG (for LHD)

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

7.READ VALUE USING GTS
a.

Disconnect the U29 multiplex network door ECU connector.


b.

Read the Data List according to the display on the GTS.

Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR CLOSER SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Back Door Courtesy SW Back door courtesy switch signal ON or OFF ON: Back door open
OFF: Back door closed
-
Body Electrical > Main Body > Data List
Tester Display
Back Door Courtesy SW
50003 123 26
OK:

The display is as specified in the normal condition column.



Result:
Proceed to
OK
NG (for RHD)
NG (for LHD)



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG (for RHD)

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG (for LHD)

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)