Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2015.10–2016.08
RM3090E _54 Brake _008767 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0048751 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1415  Rear Speed Sensor RH Output Malfunction  C1416  Rear Speed Sensor LH Output Malfunction  


DESCRIPTION

Refer to DTCs C1403 and C1404.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1403

DTC No. Detection Item DTC Detection Condition Trouble Area
C1415 Rear Speed Sensor RH Output Malfunction Either of the following is detected:
1.

An open in the sensor signal circuit of a malfunctioning area occurs 255 times or more.

2.

At a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds.

3.

At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.


·

Rear speed sensor RH (for 4WD/AWD)

·

Rear speed sensor RH (Rear axle hub and bearing assembly RH) (for 2WD)

·

Rear speed sensor RH circuit

·

Rear speed sensor rotor RH (Rear axle hub and bearing assembly RH)

·

Skid control ECU (Brake actuator assembly)

·

Wire harness or connector


C1416 Rear Speed Sensor LH Output Malfunction Either of the following is detected:
1.

An open in the sensor signal circuit of a malfunctioning area occurs 255 times or more.

2.

At a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds.

3.

At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.


·

Rear speed sensor LH (for 4WD/AWD)

·

Rear speed sensor LH (Rear axle hub and bearing assembly LH) (for 2WD)

·

Rear speed sensor LH circuit

·

Rear speed sensor rotor LH (Rear axle hub and bearing assembly LH)

·

Skid control ECU (Brake actuator assembly)

·

Wire harness or connector



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

Disassembly of the rear speed sensor from the rear axle hub and bearing assembly is prohibited (for 2WD).



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS


Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Speed Open Rear speed sensor open RH detection Normal or Error Normal Error: Momentary interruption
RL Speed Open Rear speed sensor LH open detection Normal or Error Normal Error: Momentary interruption
Chassis > ABS/VSC/TRC > Data List
Tester Display
RR Speed Open
RL Speed Open
50003 105 202,203
HINT:

Perform the above inspection before removing the sensor and connector.


OK:

Normal (There are no momentary interruptions.)


Result:
Proceed to
OK
NG (for 2WD)
NG (for 4WD/AWD)



OK

2.READ VALUE USING GTS (REAR SPEED SENSOR)

NG (for 2WD)

5.INSPECT SKID CONTROL SENSOR WIRE

NG (for 4WD/AWD)

8.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR SPEED SENSOR)
2.READ VALUE USING GTS (REAR SPEED SENSOR)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Start the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


f.

According to the display on the GTS, read the Data List.


Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed:
No large fluctuations
RL Wheel Speed Rear wheel speed sensor LH reading Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed:
No large fluctuations
Chassis > ABS/VSC/TRC > Data List
Tester Display
RR Wheel Speed
RL Wheel Speed
50003 105 3,4
g.

Check that there is no difference between the speed value output from the speed sensor displayed on the GTS and the speed value displayed on the speedometer when driving the vehicle.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK


OK:

The speed value output from the speed sensor displayed on the GTS is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE


HINT:
·

The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.

If the rear speed sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly with rear speed sensor.

·

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

4.CHECK REAR SPEED SENSOR INSTALLATION
3.RECONFIRM DTC

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105
b.

Turn the ignition switch off.


c.

Start the engine.


d.

Perform a road test.



Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Proceed to
DTCs C1415 and C1416 are not output
DTCs C1415 and/or C1416 are output



DTCs C1415 and C1416 are not output

DTCs C1415 and/or C1416 are output

4.CHECK REAR SPEED SENSOR INSTALLATION
a.

Turn the ignition switch off.


b.
C118693C01
0.676,0.188 0.859,0.363 0.183,0.176 10 *a 2.229,0.188 2.412,0.363 0.183,0.176 10 *b 1.738,1.666 1.923,1.836 0.185,0.17 10 *c
*a Normal
*b Abnormal
*c Clearance


for 2WD:

Check the speed sensor installation.

OK:

There is no clearance between the sensor and the rear axle hub.


HINT:

Because the rear axle hub and bearing assembly cannot be disassembled, if the rear speed sensor needs replacement, replace the rear axle hub and bearing assembly.



c.
C168336C14
1.994,1.633 2.181,1.795 0.186,0.161 10 *c 0.685,0.198 0.871,0.359 0.186,0.161 10 *a 2.296,0.198 2.482,0.359 0.186,0.161 10 *b
*a Normal
*b Abnormal
*c Clearance


for 4WD/AWD:

Check the rear speed sensor installation.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR(for 4WD/AWD)>INSTALLATION

OK:

There is no clearance between the sensor and the rear axle carrier.

The installation bolt is tightened properly.



Result:
Proceed to
OK (for 2WD)
OK (for 4WD/AWD)
NG (for 2WD)
NG (for 4WD/AWD)



OK (for 2WD)

5.INSPECT SKID CONTROL SENSOR WIRE

OK (for 4WD/AWD)

6.INSPECT REAR SPEED SENSOR TIP

NG (for 2WD)

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY

NG (for 4WD/AWD)

5.INSPECT SKID CONTROL SENSOR WIRE
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

for RH:

Disconnect the m1 and mM1 skid control sensor wire connectors.


d.

for LH:

Disconnect the n1 and nN1 skid control sensor wire connectors.


e.
C251359C05
0.771,0.698 1.083,0.948 0.313,0.25 0.771,0.958 1.083,1.208 0.313,0.25 2.229,0.698 2.594,0.969 0.365,0.271 2.24,0.979 2.583,1.229 0.344,0.25 0.552,2.823 0.833,1.979 false 1.094,1.99 1.375,2.813 false 0.281,0.219 0.719,0.563 0.438,0.344 10 false *a 0.833,0.74 1.146,0.938 0.313,0.198 10 false m1 0.854,0.99 1.167,1.188 0.313,0.198 10 false n1 2.271,0.76 2.729,0.958 0.458,0.198 10 false mM1 2.292,1.021 2.75,1.219 0.458,0.198 10 false nN1 2.365,1.271 2.677,1.469 0.313,0.198 10 false *c 0.875,1.271 1.188,1.469 0.313,0.198 10 false *b 1.229,0.75 1.542,0.948 0.313,0.198 10 false *A 2.75,0.75 3.063,0.948 0.313,0.198 10 false *A 1.229,1.031 1.542,1.229 0.313,0.198 10 false *B 2.75,1.031 3.063,1.229 0.313,0.198 10 false *B 1.375,2.813 2.146,3.01 0.771,0.198 10 false + 0.51,2.833 0.625,3 0.115,0.167 10 false -
*A for RH
*B for LH
*a Front view of Skid Control Sensor Wire
*b Front view of wire harness connector
(to Sensor Side Connector)
*c Front view of wire harness connector
(to Vehicle Side Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH:
Tester Connection Condition Specified Condition
m1-2 (+) - mM1-1 Always Below 1 Ω
m1-1 (-) - mM1-2 Always Below 1 Ω
m1-2 (+) - mM1-2 Always 10 kΩ or higher
m1-2 (+) or mM1-1 - Body ground Always 10 kΩ or higher
m1-1 (-) - mM1-1 Always 10 kΩ or higher
m1-1(-) or mM1-2 - Body ground Always 10 kΩ or higher

for LH:
Tester Connection Condition Specified Condition
n1-2 (+) - nN1-1 Always Below 1 Ω
n1-1 (-) - nN1-2 Always Below 1 Ω
n1-2 (+) - nN1-2 Always 10 kΩ or higher
n1-2 (+) or nN1-1 - Body ground Always 10 kΩ or higher
n1-1 (-) - nN1-1 Always 10 kΩ or higher
n1-1 (-) or nN1-2 - Body ground Always 10 kΩ or higher


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR SPEED SENSOR)

NG

6.INSPECT REAR SPEED SENSOR TIP

b.

Check the speed sensor tip.


OK:

No scratches, oil, or foreign matter on the sensor tip.


NOTICE:
·

If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.

·

If there is iron powder sticking to the rotor, this will result in a malfunction, so confirm that the rotor is not contaminated with foreign material before replacing the sensor.

·

Check the speed sensor signal after cleaning or replacement.



Result:
Proceed to
OK
NG



OK

7.INSPECT REAR AXLE HUB AND BEARING ASSEMBLY

NG

CLEAN OR REPLACE REAR SPEED SENSOR

7.INSPECT REAR AXLE HUB AND BEARING ASSEMBLY
a.

Remove the rear axle hub and bearing assembly.

Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB>REMOVAL


b.

Check the speed sensor rotor.


OK:

No scratches, oil, or foreign matter on the rotors.


NOTICE:

Check the speed sensor signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE


HINT:
·

The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.

·

If the rear speed sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly.



c.

Reinstall the rear speed sensor and rear axle hub and bearing assembly.

for the rear speed sensor: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR(for 4WD/AWD)>INSTALLATION

for the rear axle hub and bearing assembly: Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB>INSTALLATION


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR SPEED SENSOR)

NG

CLEAN OR REPLACE REAR AXLE HUB AND BEARING ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR SPEED SENSOR)
a.

for 2WD:

i.

Reconnect the mM1 (for RH) and/or nN1 (for LH) skid control sensor wire connector.


ii.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


iii.

Disconnect the A80 skid control ECU (brake actuator assembly) connector.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A80-16 (RR+) - m1-2 (+) Always Below 1 Ω
A80-15 (RR-) - m1-1 (-) Always Below 1 Ω
A80-16 (RR+) or m1-2(+) - Body ground Always 10 kΩ or higher
A80-15 (RR-) or m1-1 (-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A80-29 (RL+) - n1-2 (+) Always Below 1 Ω
A80-28 (RL-) - n1-1 (-) Always Below 1 Ω
A80-29 (RL+) or n1-2 (+) - Body ground Always 10 kΩ or higher
A80-28 (RL-) or n1-1 (-) - Body ground Always 10 kΩ or higher




b.

for 4WD/AWD:

i.

Turn the ignition switch off.


ii.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


iii.

Disconnect the A80 skid control ECU (brake actuator assembly) connector and the N11 and/or M20 rear speed sensor connector.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A80-16 (RR+) - M20-1 (RR+) Always Below 1 Ω
A80-15 (RR-) - M20-2 (RR-) Always Below 1 Ω
A80-16 (RR+) or M20-1(RR+) - Body ground Always 10 kΩ or higher
A80-15 (RR-) or M20-2 (RR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A80-29 (RL+) - N11-1 (RL+) Always Below 1 Ω
A80-28 (RL-) - N11-2 (RL-) Always Below 1 Ω
A80-29 (RL+) or N11-1 (RL+) - Body ground Always 10 kΩ or higher
A80-28 (RL-) or N11-2 (RL-) - Body ground Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

9.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT)
a.

for 2WD:

i.

Reconnect the A80 skid control ECU (brake actuator assembly) connector.


ii.

Turn the ignition switch to ON.


iii.
C233859C02
0.646,0.521 1.135,0.813 0.49,0.292 2,0.521 2.49,0.813 0.49,0.292 0.969,1.344 1.177,1.781 false 2.323,1.344 2.531,1.781 false 1.146,1.792 1.51,2.01 0.365,0.219 10 false + 2.49,1.792 2.917,2 0.427,0.208 10 false + 0.135,0.083 0.323,0.24 0.188,0.156 10 false *a 0.76,0.573 1.052,0.729 0.292,0.156 10 false m1 2.135,0.573 2.427,0.729 0.292,0.156 10 false n1 0.771,0.302 1.083,0.5 0.313,0.198 10 false *A 2.094,0.323 2.406,0.521 0.313,0.198 10 false *B
*A for RH
*B for LH
*a Front view of wire harness connector
(to Rear Speed Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Switch Condition Specified Condition
m1-2 (+) - Body ground Ignition switch ON 8 to 14 V

for LH
Tester Connection Switch Condition Specified Condition
n1-2 (+) - Body ground Ignition switch ON 8 to 14 V


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE


HINT:

The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.

If the rear speed sensor rotor needs to be replaced, replace the rear axle hub and bearing assembly with rear speed sensor.




b.

for 4WD/AWD:

i.

Reconnect the A80 skid control ECU (brake actuator assembly) connector.


ii.

Turn the ignition switch to ON.


iii.
C279422C01
0.667,0.302 1.083,0.563 0.417,0.26 2.313,0.313 2.677,0.573 0.365,0.26 1.042,1.094 1.219,1.74 false 2.656,1.75 2.531,1.115 false 2.375,0.354 2.833,0.552 0.458,0.198 10 false N11 0.75,0.354 1.208,0.552 0.458,0.198 10 false M20 1.156,1.802 1.615,2 0.458,0.198 10 false RR+ 2.563,1.813 3.021,2.01 0.458,0.198 10 false RL+ 0.781,0.073 1.094,0.271 0.313,0.198 10 false *A 2.396,0.083 2.708,0.281 0.313,0.198 10 false *B
*A for RH
*B for LH
*a Front view of wire harness connector
(to Rear Speed Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Switch Condition Specified Condition
M20-1 (RR+) - Body ground Ignition switch ON 8 to 14 V

for LH
Tester Connection Switch Condition Specified Condition
N11-1 (RL+) - Body ground Ignition switch ON 8 to 14 V


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE




Result:
Proceed to
OK
NG



OK

NG