Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2015.10–2016.08
RM3090E _54 Brake _008767 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0048751 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  Brake Warning Light Remains ON  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination assembly meter via CAN communication.

If any of the following is detected, the brake warning light remains on:

·

The skid control ECU (brake actuator assembly) connector is disconnected from the skid control ECU (brake actuator assembly).

·

The brake fluid level is insufficient.

·

The parking brake is applied.

·

EBD operation is not possible.


WIRING DIAGRAM

C350463E01
2.688,8.281 4.854,8.552 2.167,0.271 10 false : CAN Communication Line 0.073,7.667 0.385,7.865 0.313,0.198 10 false 3D 1.583,7.094 1.896,7.292 0.313,0.198 10 false G37 1.573,7.292 3.74,7.563 2.167,0.271 10 false Parking Brake Switch Assembly 1.865,6.583 2.177,6.781 0.313,0.198 10 false 1 0.073,7.833 2.896,8.115 2.823,0.281 10 false Instrument Panel Junction Block Assembly 0.333,5.073 0.646,5.271 0.313,0.198 10 false 12 0.479,4.813 0.792,5.01 0.313,0.198 10 false PKB 2.677,2.198 4.698,2.51 2.021,0.313 10 false Combination Meter Assembly 0.281,2.24 0.948,3.542 0.667,1.302 10 false Main Body ECU (Multiplex Network Body ECU) 0.292,1.969 0.604,2.167 0.313,0.198 10 false A 1.51,5.688 4.219,6.365 2.708,0.677 10 false Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Sub-assembly) 1.521,5.469 1.833,5.667 0.313,0.198 10 false A9 3.448,5.073 3.76,5.271 0.313,0.198 10 false 2 2.219,5.094 2.531,5.292 0.313,0.198 10 false 1 2.333,2.188 2.646,2.385 0.313,0.198 10 false G16 2.74,1.552 3.052,1.75 0.313,0.198 10 false SW 2.333,1.396 2.646,1.594 0.313,0.198 10 false 12 5.51,7.76 7.125,8.26 1.615,0.5 10 false Skid Control ECU (Brake Actuator Assembly) 5.49,7.51 5.802,7.708 0.313,0.198 10 false A80 6.24,3.031 6.552,3.229 0.313,0.198 10 false IG1 5.896,2.854 6.208,3.052 0.313,0.198 10 false 12 5.156,3.729 5.469,3.927 0.313,0.198 10 false *1 5.135,2.865 5.448,3.063 0.313,0.198 10 false *2 4.073,3.188 5.385,3.427 1.313,0.24 10 false ECU-IG NO. 3 2.729,3.875 3.042,4.073 0.313,0.198 10 false IG31 3.219,3.719 3.531,3.917 0.313,0.198 10 false 1 1.729,4.354 3.74,4.677 2.01,0.323 10 false Engine Stop and Start ECU*1 1.406,4.354 1.719,4.552 0.313,0.198 10 false G87 0.188,8.177 2.354,8.448 2.167,0.271 10 false *1: w/ Stop and Start System 0.198,8.51 2.365,8.781 2.167,0.271 10 false *2: w/o Stop and Start System 2.24,3.01 3.552,3.25 1.313,0.24 10 false from IG Circuit 1.031,6.625 1.344,6.823 0.313,0.198 10 false 34 5.958,6.625 6.198,6.823 0.24,0.198 10 false 25 6.198,6.74 6.656,6.927 0.458,0.188 10 false GND1

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.



PROCEDURE

1.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

2.CHECK CAN COMMUNICATION SYSTEM

NG

CONNECT CONNECTOR TO ECU CORRECTLY

2.CHECK CAN COMMUNICATION SYSTEM

Result:
Proceed to
DTC is not output
DTC is output (for LHD with Central Gateway ECU)
DTC is output (for RHD with Central Gateway ECU)
DTC is output (for LHD without Central Gateway ECU)
DTC is output (for RHD without Central Gateway ECU)



DTC is not output

3.INSPECT BATTERY

DTC is output (for LHD with Central Gateway ECU)

DTC is output (for RHD with Central Gateway ECU)

DTC is output (for LHD without Central Gateway ECU)

DTC is output (for RHD without Central Gateway ECU)

3.INSPECT BATTERY
a.

Check the battery voltage.

Standard voltage:

11 to 14 V


Result:
Proceed to
OK
NG (for 2AD-FHV)
NG (for 2AD-FTV)
NG (for 2AR-FE)
NG (for 3ZR-FAE)
NG (for 3ZR-FE)
NG (for 2WW)




OK

4.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)

NG (for 2AD-FHV)

NG (for 2AD-FTV)

NG (for 2AR-FE)

NG (for 3ZR-FAE)

NG (for 3ZR-FE)

NG (for 2WW)

CHECK OR REPLACE CHARGING SYSTEM OR BATTERY

4.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)
a.
C342353C30
1.49,0.104 1.865,0.375 0.375,0.271 2.938,0.313 2.75,0.313 2.75,0.313 2.417,0.854 true 0.104,0.104 0.417,0.26 0.313,0.156 10 false *a 1.563,0.156 2.021,0.354 0.458,0.198 10 false A80 2.99,0.24 3.271,0.438 0.281,0.198 10 false IG1
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Disconnect the A80 skid control ECU (brake actuator assembly) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A80-12 (IG1) - Body ground Ignition switch ON 11 to 14 V



d.

Turn the ignition switch off.


Result:
Proceed to
OK
NG (w/o Stop and Start System)
NG (w/ Stop and Start System)



OK

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG (w/o Stop and Start System)

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

NG (w/ Stop and Start System)

INSPECT STOP AND START SYSTEM (BACKUP BOOST CONVERTER CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.

Turn the ignition switch off.


b.
C342353C26
1.49,0.104 1.865,0.375 0.375,0.271 0.208,1.646 0.208,1.5 0.208,1.5 0.698,1.229 true 0.104,0.104 0.417,0.26 0.313,0.156 10 false *a 1.563,0.156 2.021,0.354 0.458,0.198 10 false A80 0.052,1.677 0.667,1.875 0.615,0.198 10 false GND1
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A80-25 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (PARKING BRAKE SW)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

6.READ VALUE USING GTS (PARKING BRAKE SW)
a.

Reconnect the A80 skid control ECU (brake actuator assembly) connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


f.

According to the display on the GTS, read the Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Parking Brake SW Parking brake switch assembly OFF or ON OFF: Parking brake released
ON: Parking brake applied
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Parking Brake SW
50003 105 38

g.

Using the GTS, check the input of the switch operation when the parking brake lever is operated.

OK:

The GTS displays ON or OFF according to parking brake operation.



Result:
Proceed to
OK
NG



OK

7.INSPECT BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY

NG

10.INSPECT PARKING BRAKE SWITCH ASSEMBLY
7.INSPECT BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY
a.
C235854C01
0.175,0.239 0.361,0.4 0.186,0.161 10 *a
*a Component without harness connected
(Brake Fluid Level Warning Switch [Brake Master Cylinder Reservoir Sub-assembly])


Turn the ignition switch off.


b.

Remove the reservoir filler cap and strainer.


c.

Disconnect the A9 brake fluid level warning switch (brake master cylinder reservoir sub-assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

HINT:

A float is located inside the reservoir. Its position can be changed by increasing or decreasing the level of brake fluid.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Switch off (Float up) 10 kΩ or higher
Switch on (Float down) Below 1 Ω


HINT:

If there is no problem after finishing the above check, adjust the brake fluid level to the MAX level.



Result:
Proceed to
OK
NG (for LHD)
NG (for RHD)



OK

8.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY)

NG (for LHD)

REPLACE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY

NG (for RHD)

REPLACE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY)
a.

Disconnect the G16 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-12 (SW) - A9-1 Always Below 1 Ω
A9-2 - Body ground Always Below 1 Ω
G16-12 (SW) or A9-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.READ VALUE USING GTS (BRAKE WARNING LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.READ VALUE USING GTS (BRAKE WARNING LIGHT)
a.

Reinstall the reservoir filler cap and strainer.


b.

Reconnect the G16 combination meter assembly connector and the A9 brake fluid level warning switch (brake master cylinder reservoir sub-assembly) connector.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


g.

According to the display on the GTS, read the Data List.


Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Brake Warning Light Brake warning light OFF or ON OFF: Warning light off
ON: Warning light on
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Brake Warning Light
50003 105 52
h.

Check the GTS display condition of the brake warning light.


Result:
Proceed to
Display of the Data List remains OFF
Display of the Data List remains ON



Display of the Data List remains OFF

Display of the Data List remains ON

10.INSPECT PARKING BRAKE SWITCH ASSEMBLY
a.

Remove the parking brake switch assembly.

Click hereBrake>PARKING BRAKE>PARKING BRAKE SWITCH>REMOVAL


b.

Inspect the parking brake switch assembly.

Click hereBrake>PARKING BRAKE>PARKING BRAKE SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - PARKING BRAKE SWITCH ASSEMBLY)

NG

REPLACE PARKING BRAKE SWITCH ASSEMBLY

11.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - PARKING BRAKE SWITCH ASSEMBLY)
a.

Disconnect the 3D instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3D-34 - G37-1 Always Below 1 Ω
3D-34 or G37-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL

for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL


c.
C284585C02
0.063,0.906 0.365,1.167 0.302,0.26 1.479,2.146 1.823,2.406 0.344,0.26 1.365,2.823 1.188,3.115 false 0.094,0.958 0.406,1.156 0.313,0.198 10 false 3D 1.594,2.188 1.75,2.385 0.156,0.198 10 false A 1.021,3.146 1.479,3.344 0.458,0.198 10 false PKB 0,0 0.313,0.156 0.313,0.156 10 false *a
*a Component without harness connected
(Instrument Panel Junction Block Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3D-34 - A-12 (PKB) Always Below 1 Ω
3D-34 or A-12 (PKB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK (for LHD)
OK (for RHD)
NG (for LHD)
NG (for RHD)



OK (for LHD)

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

OK (for RHD)

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG (for LHD)

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG (for RHD)

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY