Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) › from 2015.10
RM3090E _57 Power Source / Network _008434 NETWORKING _0221950 CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) C

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)  U023A  Lost Communication with Front Camera Module  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
U023A Lost Communication with Front Camera Module There is no communication from the forward recognition camera.
·

Power source or inside forward recognition camera

·

Forward recognition camera CAN main wire or connector

·

Forward recognition camera


Driving support ECU assembly

WIRING DIAGRAM

C334649E03
5.208,3.813 7.052,4.198 1.844,0.385 10 false Forward Recognition Camera 5.198,3.635 5.656,3.833 0.458,0.198 10 false Q17 5.625,0.521 6.24,0.719 0.615,0.198 10 false CANH 5.646,1.396 6.26,1.594 0.615,0.198 10 false CANL 5.625,2.094 6.24,2.292 0.615,0.198 10 false IGB 5.625,3.219 6.24,3.417 0.615,0.198 10 false GND 1.719,0.563 1.875,0.76 0.156,0.198 10 false 6 1.708,1.135 2.021,1.333 0.313,0.198 10 false 17 0.135,1.458 0.594,1.656 0.458,0.198 10 false G173 0.156,1.646 2.76,2.021 2.604,0.375 10 false No. 8 CAN Junction Connector 5.333,0.521 5.49,0.719 0.156,0.198 10 false 6 5.281,1.135 5.594,1.333 0.313,0.198 10 false 12 5.344,1.938 5.5,2.135 0.156,0.198 10 false 7 5.313,3.115 5.625,3.313 0.313,0.198 10 false 10 3.948,1.906 4.99,2.104 1.042,0.198 10 false ECU-IG NO.2 3.729,2.208 3.958,2.427 0.229,0.219 10 false *1 3.75,2.906 3.979,3.125 0.229,0.219 10 false *2 1.885,2.094 3.427,2.365 1.542,0.271 10 false from IG1 NO.1 Relay*1 1.177,2.771 3.396,3.063 2.219,0.292 10 false from Engine Stop and Start ECU*2 0.302,3.688 2.521,3.979 2.219,0.292 10 false *1: w/o Stop and Start System 0.313,4.125 2.531,4.417 2.219,0.292 10 false *2: w/ Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 20 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220
HINT:

If DTC U1002 is output from gateway of the driving support ECU assembly, this indicates a local bus malfunction. Troubleshoot for DTC U1002 and check for malfunctions in local bus.



Result:
Result Proceed to
DTC U1002 is not output from driving support ECU assembly A
DTC U1002 is output from driving support ECU assembly B



A

2.CHECK FOR OPEN IN CAN BUS WIRE (FORWARD RECOGNITION CAMERA CAN MAIN WIRE)

B

GO TO GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

2.CHECK FOR OPEN IN CAN BUS WIRE (FORWARD RECOGNITION CAMERA CAN MAIN WIRE)
a.
C268302C36
0.333,1.208 0.771,1.448 0.438,0.24 2.063,1.26 2.344,0.865 2.344,0.865 2.49,0.865 true 2.083,1.521 2.271,1.802 2.271,1.802 2.469,1.802 true 0.052,0.042 0.365,0.198 0.313,0.156 10 false *a 0.417,1.24 0.729,1.396 0.313,0.156 10 false Q17 2.521,1.708 3.021,1.885 0.5,0.177 10 false CANL 2.552,0.76 3.052,0.938 0.5,0.177 10 false CANH
*a Front view of wire harness connector
(to Forward Recognition Camera)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the forward recognition camera connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q17-6 (CANH) - Q17-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result Proceed to
OK (w/o Stop and Start System) A
OK (w/ Stop and Start System) B
NG C



A

3.CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION CAMERA - BATTERY AND BODY GROUND)

B

4.CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION CAMERA - BATTERY AND BODY GROUND)

C

REPAIR OR REPLACE FORWARD RECOGNITION CAMERA CAN MAIN WIRE OR CONNECTOR (CANH, CANL)

3.CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION CAMERA - BATTERY AND BODY GROUND)
a.
C268302C35
0.333,1.208 0.771,1.448 0.438,0.24 1.792,1.521 2.146,1.781 2.146,1.781 2.344,1.781 true 0.958,1.792 1.135,1.792 1.135,1.792 1.354,1.5 true 0.052,0.042 0.365,0.198 0.313,0.156 10 false *a 0.427,1.24 0.844,1.448 0.417,0.208 10 false Q17 2.385,1.698 2.885,1.875 0.5,0.177 10 false GND 0.677,1.708 1.177,1.885 0.5,0.177 10 false IGB
*a Front view of wire harness connector
(to Forward Recognition Camera)


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Q17-7 (IGB) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q17-10 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION CAMERA - BATTERY AND BODY GROUND)
a.
C268302C35
0.333,1.208 0.771,1.448 0.438,0.24 1.792,1.521 2.146,1.781 2.146,1.781 2.344,1.781 true 0.958,1.792 1.135,1.792 1.135,1.792 1.354,1.5 true 0.052,0.042 0.365,0.198 0.313,0.156 10 false *a 0.427,1.24 0.844,1.448 0.417,0.208 10 false Q17 2.385,1.698 2.885,1.875 0.5,0.177 10 false GND 0.677,1.708 1.177,1.885 0.5,0.177 10 false IGB
*a Front view of wire harness connector
(to Forward Recognition Camera)


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Q17-7 (IGB) - Body ground Ignition switch ON 10.5 to 16 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q17-10 (GND) - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK A
NG (IGB terminal) B
NG (GND terminal) C



A

REPLACE FORWARD RECOGNITION CAMERA

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR