Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › from 2015.10
RM3090E _55 Steering _008772 POWER ASSIST SYSTEMS _0049011 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1551/25  IG Power Supply Voltage Malfunction  


DESCRIPTION

The power steering ECU assembly distinguishes the ignition switch status as ON or off through the IG power source circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Return-to-normal Condition
C1551/25 IG Power Supply Voltage Malfunction IG power source circuit malfunction inside ECU
·

EPS-IG fuse (w/o Stop and start system)

·

IG power source circuit

·

ECU wire sub-assembly

·

Power steering ECU assembly


On Ignition switch ON again

WIRING DIAGRAM

C277338E01
0.188,1.448 1.667,1.688 1.479,0.24 10 Stop and Start System 0.708,0.854 1.698,1.094 0.99,0.24 10 from IG Circuit 2.24,1.042 2.792,1.313 0.552,0.271 10 EPS-IG 0.198,2.656 2.573,2.927 2.375,0.271 10 *1: ECU Wire Sub-assembly 0.208,2.938 2.583,3.208 2.375,0.271 10 *2: w/o Stop and Start System 0.219,3.229 2.594,3.5 2.375,0.271 10 *3: w/ Stop and Start System 4.844,3 6.802,3.323 1.958,0.323 10 Power Steering ECU Assembly 5.115,0.896 5.667,1.167 0.552,0.271 10 IG 5.115,2.146 5.667,2.417 0.552,0.271 10 PGND 4.74,2.156 4.958,2.385 0.219,0.229 10 h2 4.75,0.875 4.969,1.104 0.219,0.229 10 h1 4.781,1.938 4.938,2.146 0.156,0.208 10 2 4.771,0.667 4.948,0.865 0.177,0.198 10 1 3.458,0.656 3.635,0.854 0.177,0.198 10 5 3.365,0.865 3.708,1.083 0.344,0.219 10 hG1 2.771,0.729 3.115,0.948 0.344,0.219 10 *2 2.771,1.313 3.115,1.531 0.344,0.219 10 *3 4.167,0.75 4.51,0.969 0.344,0.219 10 *1 3.938,2.021 4.281,2.24 0.344,0.219 10 *1

CAUTION / NOTICE / HINT

NOTICE:
·

If the power steering ECU assembly has been replaced, perform assist map writing (Click here Steering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION AND GROUND WIRE
a.

Check the connection condition of the ECU wire sub-assembly and power steering ECU assembly connectors.

OK:

The ECU wire sub-assembly and power steering ECU assembly connectors are securely connected.



b.

Check that the ground wire is securely installed with the bolt.

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>INSTALLATION

OK:

The ground wire is securely installed with the bolt.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (IG POWER SUPPLY)

NG

CONNECT CONNECTOR OR INSTALL GROUND WIRE

2.READ VALUE USING GTS (IG POWER SUPPLY)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / EMPS / Data List.


f.

Select the item "IG power supply" in the Data List and read the value displayed on the GTS.

Chassis > EMPS > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
IG Power Supply ECU power source voltage Min.: 0.0000 V
Max.: 20.1531 V
Ignition switch ON: 11 to 14 V -
Chassis > EMPS > Data List
Tester Display
IG Power Supply
50003 142 11
OK:

The normal condition value is displayed on the GTS.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (IG POWER SUPPLY)
3.CHECK HARNESS AND CONNECTOR (IG POWER SUPPLY)
a.
C278679C01
0.729,0.635 1.167,0.938 0.438,0.302 1.958,1.406 2.51,1.427 false 2.594,1.365 2.906,1.615 0.313,0.25 10 IG 0.833,0.708 1.146,0.906 0.313,0.198 10 hG1 0.135,0.094 0.448,0.25 0.313,0.156 10 *a
*a Front view of wire harness connector
(to ECU Wire Sub-assembly)


Disconnect the hG1 ECU wire sub-assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
hG1-5 (IG) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG (w/o Stop and Start System)
NG (w/ Stop and Start System)



OK

4.CHECK ECU WIRE SUB-ASSEMBLY

NG (w/o Stop and Start System)

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG (w/ Stop and Start System)

4.CHECK ECU WIRE SUB-ASSEMBLY
a.
C240351C03
0.344,3.271 0.792,3.552 0.448,0.281 0.604,0.906 1.052,1.188 0.448,0.281 2.271,3.531 2.354,4.135 false 1.115,1.677 1.49,1.802 false 0.198,0.146 0.635,0.458 0.438,0.313 10 *a 0.51,3.333 0.948,3.729 0.438,0.396 10 h2 2.177,4.177 2.906,4.51 0.729,0.333 10 PGND 0.917,1.583 1.344,1.948 0.427,0.365 10 IG 0.771,0.969 1.156,1.354 0.385,0.385 10 h1
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


Connect the hG1 connector to the ECU wire sub-assembly.


b.

Disconnect the h1 and h2 power steering ECU assembly connectors.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
h1-1 (IG) - Body ground Ignition switch ON 11 to 14 V



e.

Turn the ignition switch off.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
h2-2 (PGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE ECU WIRE SUB-ASSEMBLY