Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/ Entry and Start System) › from 2015.10
RM3090E _58 Vehicle Interior _008690 THEFT DETERRENT / KEYLESS ENTRY _0048164 IMMOBILISER SYSTEM(w/ Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/ Entry and Start System)  B2799  Immobiliser Malfunction  


DESCRIPTION

·

w/ ID code box (Immobiliser Code ECU):

When there is a communication malfunction between the ECM and ID code box (immobiliser code ECU), or when the communication ID codes do not match, the ECM stores this DTC.

·

w/o ID code box (Immobiliser Code ECU):

When there are communication malfunctions between the ECM and certification ECU (smart key ECU assembly), or when the communication ID codes do not match, the ECM stores this DTC.


DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2799 Immobiliser Malfunction Either condition is met (1 trip detection logic*3):
·

A malfunction in the communication or communication lines between the ECM and ID code box (immobiliser code ECU)*1 or certification ECU (smart key ECU assembly)*2.

·

A matching communication code cannot be verified during communication between the ECM and ID code box (immobiliser code ECU)*1 or certification ECU (smart key ECU assembly)*2.


·

ID code box (immobiliser code ECU)*1

·

Certification ECU (smart key ECU assembly)*2

·

ECM

·

Harness or connector


DTC output confirmation operation (Either condition is met):
·

Within 10 seconds of an engine start operation being performed (with the shift lever in P*4 and the brake pedal*4 or clutch pedal*5 depressed, the engine switch is pressed while the key is being carried). If there is a malfunction, the engine stops (communication begins within 3 seconds of the engine start operation being performed, and DTCs are stored after 6 seconds).

·

10 seconds after the engine switch is turned on (IG) after reconnecting the cable to the negative (-) battery terminal (communication begins within 3 seconds of the engine switch being turned on (IG), and DTCs are stored after 6 seconds).



*1: w/ ID code box (Immobiliser Code ECU)

*2: w/o ID code box (Immobiliser Code ECU)

*3: Only output while a malfunction is present.

*4: except Manual Transaxle

*5: for Manual Transaxle


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started -

Related Data List and Active Test
DTC No. Data List and Active Test
B2799 -

WIRING DIAGRAM

1. for 3ZR Series Engine


B278902E08
1.115,1.667 1.583,1.906 0.469,0.24 10 false A62 1.156,1.833 2.906,2.021 1.75,0.188 10 false ECM 5.469,0.573 5.865,0.76 0.396,0.188 10 false EFIO 5.469,2.854 5.865,3.042 0.396,0.188 10 false EFIO 5.469,1.031 5.865,1.219 0.396,0.188 10 false EFII 5.469,3.406 5.865,3.594 0.396,0.188 10 false EFII 1.438,0.573 1.833,0.76 0.396,0.188 10 false IMI 1.406,1.042 1.802,1.229 0.396,0.188 10 false IMO 1.802,0.5 2.5,0.677 0.698,0.177 10 false 28 1.802,0.969 3.24,1.177 1.438,0.208 10 false 29*3 5.198,0.49 5.49,0.698 0.292,0.208 10 false 13 5.208,0.969 5.5,1.177 0.292,0.208 10 false 14 5.292,3.302 5.417,3.479 0.125,0.177 10 false 3 5.292,2.729 5.417,2.906 0.125,0.177 10 false 4 5.094,1.552 5.542,1.844 0.448,0.292 10 false G82 5.094,3.792 5.51,4.146 0.417,0.354 10 false G44 5.094,1.719 6.635,2.042 1.542,0.323 10 false Certification ECU (Smart Key ECU Assembly) 5.094,3.99 6.677,4.385 1.583,0.396 10 false ID Code Box (Immobiliser Code ECU) 0.052,3.563 3.438,3.802 3.385,0.24 10 false *1: w/ ID code box (Immobiliser Code ECU) 0.052,3.844 3.74,4.063 3.688,0.219 10 false *2: w/o ID code box (Immobiliser Code ECU) 4.396,0.448 4.656,0.74 0.26,0.292 10 false *2 4.396,0.927 4.688,1.177 0.292,0.25 10 false *2 3.188,2.208 3.74,2.698 0.552,0.49 10 false *1 4.042,2.208 4.438,2.542 0.396,0.333 10 false *1 1.802,1.167 3.24,1.375 1.438,0.208 10 false 45*4 0.052,4.115 3.74,4.333 3.688,0.219 10 false *3: for K111, K111F 0.042,4.396 3.729,4.615 3.688,0.219 10 false *4: except K111, K111F


2. except 3ZR Series Engine


B278902E06
1.104,1.646 1.802,1.896 0.698,0.25 10 false A62*3, *4 1.104,1.969 1.646,2.344 0.542,0.375 10 false ECM 5.469,0.573 5.865,0.76 0.396,0.188 10 false EFIO 5.469,2.854 5.865,3.042 0.396,0.188 10 false EFIO 5.469,1.031 5.865,1.219 0.396,0.188 10 false EFII 5.469,3.406 5.865,3.594 0.396,0.188 10 false EFII 1.438,0.573 1.833,0.76 0.396,0.188 10 false IMI 1.406,1.042 1.802,1.229 0.396,0.188 10 false IMO 1.802,0.5 2.5,0.677 0.698,0.177 10 false 28*3, 34*4 1.802,0.969 3.24,1.177 1.438,0.208 10 false 29*3, 44*4 5.198,0.49 5.49,0.698 0.292,0.208 10 false 13 5.208,0.969 5.5,1.177 0.292,0.208 10 false 14 5.292,3.302 5.417,3.479 0.125,0.177 10 false 3 5.292,2.729 5.417,2.906 0.125,0.177 10 false 4 5.094,1.552 5.542,1.844 0.448,0.292 10 false G82 5.094,3.792 5.51,4.146 0.417,0.354 10 false G44 5.094,1.719 6.635,2.042 1.542,0.323 10 false Certification ECU (Smart Key ECU Assembly) 5.094,3.99 6.677,4.385 1.583,0.396 10 false ID Code Box (Immobiliser Code ECU) 0.052,3.271 3.438,3.51 3.385,0.24 10 false *1: w/ ID code box (Immobiliser Code ECU) 0.052,3.552 3.74,3.771 3.688,0.219 10 false *2: w/o ID code box (Immobiliser Code ECU) 4.396,0.448 4.656,0.74 0.26,0.292 10 false *2 4.396,0.927 4.688,1.177 0.292,0.25 10 false *2 3.188,2.208 3.74,2.698 0.552,0.49 10 false *1 4.042,2.208 4.438,2.542 0.396,0.333 10 false *1 1.104,1.802 1.771,2.042 0.667,0.24 10 false A61*5 1.792,0.688 2.49,0.865 0.698,0.177 10 false 16*5 0.052,3.854 3.74,4.073 3.688,0.219 10 false *3: for 2AR-FE 0.052,4.135 3.74,4.354 3.688,0.219 10 false *4: for 2WW 0.042,4.417 3.729,4.635 3.688,0.219 10 false *5: for 2AD-FHV, 2AD-FTV 1.792,1.177 2.49,1.354 0.698,0.177 10 false 15*5


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the certification ECU (smart key ECU assembly)*1 or ID code box (immobiliser code ECU)*2, refer to the Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".


*1: w/ ID code box (Immobiliser Code ECU)

*2: w/o ID code box (Immobiliser Code ECU)



HINT:

When DTC B2799 and a certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.


PROCEDURE

1.SYSTEM CHECK
a.

Check the vehicle specification.


Result:
Proceed to
NEXT



NEXT

2.CHECK HARNESS AND CONNECTOR (ID CODE BOX [IMMOBILISER CODE ECU] OR CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - ECM)
2.CHECK HARNESS AND CONNECTOR (ID CODE BOX [IMMOBILISER CODE ECU] OR CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - ECM)

*1: w/ ID code box (Immobiliser Code ECU)

*2: w/o ID code box (Immobiliser Code ECU)

*3: for 3ZR-FE (for K111, K111F), 3ZR-FEA, 2AR-FE

*4: for 3ZR-FE (except K111, K111F)

*5: for 2WW

*6: for 2AD-FHV, 2AD-FTV


a.

Disconnect the G44 ID code box (immobiliser code ECU) connector.*1


b.

Disconnect the G82 certification ECU (smart key ECU assembly) connector.*2


c.

Disconnect the A62*3, *4, *5 or A61*6 ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 3ZR-FE (for K111, K111F), 3ZR-FEA, 2AR-FR
Tester Connection Condition Specified Condition
G44-3 (EFII) - A62-29 (IMO)*1 Always Below 1 Ω
G82-14 (EFII) - A62-29 (IMO)*2
A62-29 (IMO) - Body ground Always 10 kΩ or higher
G44-3 (EFII) - Body ground*1 Always 10 kΩ or higher
G82-14 (EFII) - Body ground*2 Always 10 kΩ or higher
G44-4 (EFIO) - A62-28 (IMI)*1 Always Below 1 Ω
G82-13 (EFIO) - A62-28 (IMI)*2
A62-28 (IMI) - Body ground Always 10 kΩ or higher
G44-4 (EFIO) - Body ground*1 Always 10 kΩ or higher
G82-13 (EFIO) - Body ground*2 Always 10 kΩ or higher

for 3ZR-FE (except K111, K111F)
Tester Connection Condition Specified Condition
G44-3 (EFII) - A62-45 (IMO)*1 Always Below 1 Ω
G82-13 (EFII) - A62-45 (IMO)*2
A62-45 (IMO) - Body ground Always 10 kΩ or higher
G44-3 (EFII) - Body ground*1 Always 10 kΩ or higher
G82-14 (EFII) - Body ground*2 Always 10 kΩ or higher
G44-4 (EFIO) - A62-28 (IMI)*1 Always Below 1 Ω
G82-13 (EFIO) - A62-28 (IMI)*2
A62-28 (IMI) - Body ground Always 10 kΩ or higher
G44-4 (EFIO) - Body ground*1 Always 10 kΩ or higher
G82-13 (EFIO) - Body ground*2 Always 10 kΩ or higher

for 2WW
Tester Connection Condition Specified Condition
G44-3 (EFII) - A62-44 (IMO)*1 Always Below 1 Ω
A62-44 (IMO) - Body ground Always 10 kΩ or higher
G44-3 (EFII) - Body ground*1 Always 10 kΩ or higher
G44-4 (EFIO) - A62-34 (IMI)*1 Always Below 1 Ω
A62-34 (IMI) - Body ground Always 10 kΩ or higher
G44-4 (EFIO) - Body ground*1 Always 10 kΩ or higher

for 2AD-FHV, 2AD-FTV
Tester Connection Condition Specified Condition
G44-3 (EFII) - A61-15 (IMO)*1 Always Below 1 Ω
G82-14 (EFII) - A61-15 (IMO)*2
A61-15 (IMO) - Body ground Always 10 kΩ or higher
G44-3 (EFII) - Body ground*1 Always 10 kΩ or higher
G82-14 (EFII) - Body ground*2 Always 10 kΩ or higher
G44-4 (EFIO) - A61-16 (IMI)*1 Always Below 1 Ω
G82-13 (EFIO) - A61-16 (IMI)*2
A61-16 (IMI) - Body ground Always 10 kΩ or higher
G44-4 (EFIO) - Body ground*1 Always 10 kΩ or higher
G82-13 (EFIO) - Body ground*2 Always 10 kΩ or higher


*1: w/ ID code box (Immobiliser Code ECU)

*2: w/o ID code box (Immobiliser Code ECU)



Result:
Proceed to
OK
NG



OK

3.REGISTER ECU COMMUNICATION ID

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

4.CLEAR DTC
4.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61
Powertrain > Engine and ECT > Clear DTCs
50002 234

Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 61
Powertrain > Engine and ECT > Trouble Codes
50001 234
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.



Result:
Proceed to
B2799 is not output
B2799 is output
Other DTCs are output



B2799 is not output

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE)

B2799 is output

6.REPLACE ECM

Other DTCs are output

6.REPLACE ECM

NEXT

7.REGISTER ECU COMMUNICATION ID
7.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

8.CLEAR DTC
8.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61
Powertrain > Engine and ECT > Clear DTCs
50002 234

Result:
Proceed to
NEXT



NEXT

9.CHECK FOR DTC
9.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 61
Powertrain > Engine and ECT > Trouble Codes
50001 234
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC B2799 is not output.



Result:
Proceed to
OK
NG (w/ ID code box [Immobiliser Code ECU])
NG (w/o ID code box [Immobiliser Code ECU])



OK

END (ECM WAS DEFECTIVE)

NG (w/ ID code box [Immobiliser Code ECU])

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

NG (w/o ID code box [Immobiliser Code ECU])

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)