Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/o Entry and Start System) › from 2015.10
RM3090E _58 Vehicle Interior _008690 THEFT DETERRENT / KEYLESS ENTRY _0048166 IMMOBILISER SYSTEM(w/o Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/o Entry and Start System)  B279A  Theft Deterrent System Communication Line High Fixation  


DESCRIPTION

If the communication line (EFIO-IMI) to the transponder key ECU assembly is stuck high (e.g. shorted to +B), the ECM stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B279A Theft Deterrent System Communication Line High Fixation Communication line (EFIO-IMI) between the ECM and transponder key ECU assembly is stuck high.
·

Harness or connector

·

ECM

·

Transponder key ECU assembly


DTC Output Confirmation Operation:

Turn the ignition switch to ON and wait 6 seconds.



Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started (initial ignition occurs and engine cranks, then ignition stops) Engine cannot be started

Related Data List and Active Test
DTC No. Data List and Active Test
B279A -

WIRING DIAGRAM

B434573E01
5.438,1.823 5.896,2.021 0.458,0.198 10 false G88 5.458,1.979 6.938,2.427 1.479,0.448 10 false Transponder Key ECU Assembly 5.458,1.01 5.917,1.208 0.458,0.198 10 false EFIO 5.25,0.906 5.708,1.104 0.458,0.198 10 false 13 1.49,0.99 1.948,1.188 0.458,0.198 10 false IMI 1.094,1.823 1.802,1.979 0.708,0.156 10 false A62*1, *2 1.146,2.167 1.604,2.365 0.458,0.198 10 false ECM 1.781,0.917 2.594,1.094 0.813,0.177 10 false 28*1, 34*2 1.792,1.115 2.25,1.313 0.458,0.198 10 false 16*3 2.198,1.917 4.854,2.104 2.656,0.188 10 false *1: for 3ZR-FE, 3ZR-FAE, 2AR-FE 2.198,2.156 4.854,2.344 2.656,0.188 10 false *2: for 2WW 2.198,2.406 4.854,2.594 2.656,0.188 10 false *3: for 2AD-FHV, 2AD-FTV 1.083,2 1.792,2.156 0.708,0.156 10 false A61*3


CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly or ECM is replaced, refer to the Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

·

When using the GTS with the vehicle ignition switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Immobiliser. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234
Powertrain > Engine > Clear DTCs
50002 61

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234
Powertrain > Engine > Trouble Codes
50001 61
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.



Result:
Proceed to
B279A is not output
B279A is output



B279A is not output

B279A is output

3.CHECK CONNECTION OF CONNECTOR
3.CHECK CONNECTION OF CONNECTOR
a.

Check that the connectors are properly connected to the ECM and transponder key ECU assembly.

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)

NG

CONNECT CONNECTORS PROPERLY

4.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)
a.

Disconnect the G88 transponder key ECU assembly connector.


b.

Disconnect the A62*1, *2 or A61*3 ECM connector.

*1: for 3ZR-FE, 3ZR-FAE, 2AR-FE

*2: 2WW

*3: 2AD-FHV, 2AD-FTV



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 3ZR-FE, 3ZR-FAE, 2AR-FE
Tester Connection Condition Specified Condition
G44-4 (EFIO) - A62-28 (IMI) Always Below 1 Ω
A62-28 (IMI) - Body ground Always 10 kΩ or higher
G44-4 (EFIO) - Body ground Always 10 kΩ or higher

for 2WW
Tester Connection Condition Specified Condition
G44-4 (EFIO) - A62-34 (IMI) Always Below 1 Ω
A62-34 (IMI) - Body ground Always 10 kΩ or higher
G44-4 (EFIO) - Body ground Always 10 kΩ or higher

for 2AD-FHV, 2AD-FTV
Tester Connection Condition Specified Condition
G44-4 (EFIO) - A61-16 (IMI) Always Below 1 Ω
A61-16 (IMI) - Body ground Always 10 kΩ or higher
G44-4 (EFIO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one.

HINT:

Refer to the Service Bulletin.


NOTICE:

Key ID code registration is necessary when replacing the transponder key ECU assembly.

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

6.CLEAR DTC
6.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234
Powertrain > Engine > Clear DTCs
50002 61

Result:
Proceed to
NEXT



NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234
Powertrain > Engine > Trouble Codes
50001 61
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.



Result:
Proceed to
B279A is not output
B279A is output (for 2AR-FE)
B279A is output (for 3ZR-FAE)
B279A is output (for 3ZR-FE)
B279A is output (for 2WW)
B279A is output (for 2AD-FTV)
B279A is output (for 2AD-FHV)



B279A is not output

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

B279A is output (for 2AR-FE)

B279A is output (for 3ZR-FAE)

B279A is output (for 3ZR-FE)

B279A is output (for 2WW)

B279A is output (for 2AD-FTV)

B279A is output (for 2AD-FHV)