Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _008749 CRUISE CONTROL _0226194 DYNAMIC RADAR CRUISE CONTROL SYSTEM J

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  Distance Control Switch Circuit  


DESCRIPTION

The vehicle-to-vehicle distance control switch is used to set the distance for vehicle-to-vehicle distance control mode. The vehicle-to-vehicle distance control switch is installed in the steering pad switch assembly. The vehicle-to-vehicle distance set value can be changed by operating the vehicle-to-vehicle distance control switch (steering pad switch assembly) while the dynamic radar cruise control system is controlling vehicle speed in vehicle-to-vehicle distance control mode.

WIRING DIAGRAM

C365838E01
0.823,0.594 2.417,0.917 1.594,0.323 10 false Vehicle-to-vehicle Distance Control Switch 2.521,0.469 2.833,0.667 0.313,0.198 10 false z1 2.521,1.844 2.833,2.042 0.313,0.198 10 false z1 3.74,0.469 4.052,0.667 0.313,0.198 10 false G8 3.75,1.844 4.063,2.042 0.313,0.198 10 false G8 2.542,1.604 2.698,1.802 0.156,0.198 10 false 7 2.542,0.24 2.698,0.438 0.156,0.198 10 false 4 3.74,0.24 4.052,0.438 0.313,0.198 10 false 12 3.792,1.615 4.104,1.813 0.313,0.198 10 false 2 3.063,0.365 3.677,0.563 0.615,0.198 10 false DIST 3.073,1.74 3.688,1.938 0.615,0.198 10 false ECC 6.021,0.344 6.333,0.542 0.313,0.198 10 false 23 6.292,0.469 6.906,0.667 0.615,0.198 10 false SPSW 5.156,0.906 5.771,1.104 0.615,0.198 10 false G168 5.167,1.052 7.156,1.302 1.99,0.25 10 false Driving Support ECU Assembly 0.396,2.146 2.417,2.417 2.021,0.271 10 false Steering Pad Switch Assembly 2.771,2.135 3.74,2.604 0.969,0.469 10 false Spiral Cable Sub-assembly 5.49,1.844 5.948,2.042 0.458,0.198 10 false A62 5.906,1.844 6.365,2.042 0.458,0.198 10 false A62 5.521,1.615 5.979,1.813 0.458,0.198 10 false 42 5.948,1.615 6.406,1.813 0.458,0.198 10 false 35 6.292,1.844 7.063,2.042 0.771,0.198 10 false ECCS 6.448,2.26 6.906,2.458 0.458,0.198 10 false ECM 5.521,2.073 5.833,2.271 0.313,0.198 10 false *1 5.958,2.073 6.271,2.271 0.313,0.198 10 false *2 4.865,2.135 5.177,2.333 0.313,0.198 10 false *3 0.135,2.615 2.427,2.813 2.292,0.198 10 false *1: for 2WW 0.146,2.99 6.875,3.188 6.729,0.198 10 false *2: for 3ZR-FAE, 3ZR-FE (except K111, K111F) 0.156,3.365 5.688,3.646 5.531,0.281 10 false *3: except 2WW, 3ZR-FAE, 3ZR-FE (except K111, K111F)

PROCEDURE

1.READ VALUE USING GTS (DISTANCE CONTROL SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Radar Cruise2 / Data List.


e.

Check the Data List to confirm function of the distance control switch.

Powertrain > Radar Cruise2 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Distance Control Switch Distance control switch signal ON or OFF ON: Distance control switch on
OFF: Distance control switch off
-
Powertrain > Radar Cruise2 > Data List
Tester Display
Distance Control Switch
50003 197 5
OK:

The display changes in accordance with switch operation.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT STEERING PAD SWITCH ASSEMBLY
2.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY

OK

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY)
a.

for 2WW:

i.

Disconnect the G8 spiral cable sub-assembly connector.


ii.

Disconnect the G168 driving support ECU assembly connector.


iii.

Disconnect the A62 ECM connector.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-12 (DIST) - G168-23 (SPSW) Always Below 1 Ω
G8-12 (DIST) or G168-23 (SPSW) - Body ground Always 10 kΩ or higher
G8-2 (ECC) - A62-42 (ECCS) Always Below 1 Ω




b.

for 3ZR-FAE, 3ZR-FE (except K111, K111F):

i.

Disconnect the G8 spiral cable sub-assembly connector.


ii.

Disconnect the G168 driving support ECU assembly connector.


iii.

Disconnect the A62 ECM connector.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-12 (DIST) - G168-23 (SPSW) Always Below 1 Ω
G8-12 (DIST) or G168-23 (SPSW) - Body ground Always 10 kΩ or higher
G8-2 (ECC) - A62-35 (ECCS) Always Below 1 Ω




c.

except 2WW, 3ZR-FAE, 3ZR-FE (except K111, K111F):

i.

Disconnect the G8 spiral cable sub-assembly connector.


ii.

Disconnect the G168 driving support ECU assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-12 (DIST) - G168-23 (SPSW) Always Below 1 Ω
G8-12 (DIST) or G168-23 (SPSW) - Body ground Always 10 kΩ or higher
G8-2 (ECC) - Body ground Always Below 1 Ω




Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR