Home › Engine / Hybrid System › 3ZR-FAE ENGINE CONTROL › SFI SYSTEM › 2015.10–2016.08
RM3090E _51 Engine / Hybrid System _008381 3ZR-FAE ENGINE CONTROL _0048627 SFI SYSTEM J

3ZR-FAE ENGINE CONTROL  SFI SYSTEM  VC Output Circuit  


DESCRIPTION

The ECM constantly generates a 5 V power source voltage from the battery voltage supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power source voltage to the sensors through the VC output circuit.

A206916E22
4.375,1.177 6.198,1.354 1.823,0.177 10 5 V Constant Voltage Circuit 5.354,2.031 6.365,2.188 1.01,0.156 10 Microprocessor 0.99,1.156 2.625,1.365 1.635,0.208 10 from EFI-MAIN NO.2 Fuse 0.938,1.479 2.604,1.646 1.667,0.167 10 from EFI-MAIN NO.1 Relay 2.906,1 3.427,1.219 0.521,0.219 10 BATT 0.313,2.135 2.635,2.677 2.323,0.542 10 Throttle Position Sensor, Accelerator Pedal Position Sensor, etc. (Sensors which have IC) 0.313,3.021 2.677,3.448 2.365,0.427 10 Engine Coolant Temperature Sensor, Intake Air Temperature Sensor, etc. 4.073,3.115 4.333,3.323 0.26,0.208 10 R 2.813,1.354 3.375,1.552 0.563,0.198 10 +B, +B2 3.167,2.271 3.458,2.5 0.292,0.229 10 VC 4.885,3.333 5.229,3.51 0.344,0.177 10 ECM

When the VC circuit is short-circuited, the microprocessor in the ECM and the sensors that are supplied with power through the VC circuit are inactivated because power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:

Under normal conditions, the MIL is illuminated when the ignition switch is turned to ON. The MIL goes off when the engine is started.


WIRING DIAGRAM

A282859E15
5.333,0.969 5.917,1.198 0.583,0.229 10 false ETA 5.323,1.792 6.094,2.188 0.771,0.396 10 false VTA2 5.323,1.427 5.906,1.646 0.583,0.219 10 false VTA1 5.323,0.604 6.083,0.906 0.76,0.302 10 false VCTA 5.323,2.198 6.01,2.458 0.688,0.26 10 false VCPA 5.333,4.01 5.875,4.25 0.542,0.24 10 false EPA2 5.323,3.417 5.948,3.688 0.625,0.271 10 false VPA2 5.323,2.563 6.083,2.833 0.76,0.271 10 false VCP2 5.333,3.646 5.729,3.833 0.396,0.188 10 false EPA 5.323,3.052 5.896,3.344 0.573,0.292 10 false VPA 5,2.292 5.448,2.479 0.448,0.188 10 false A62 5.042,2.115 5.479,2.396 0.438,0.281 10 false 49 5,3.021 5.417,3.313 0.417,0.292 10 false A62 5.042,2.854 5.344,3.083 0.302,0.229 10 false 47 4.99,3.75 5.396,3.99 0.406,0.24 10 false A62 5.031,3.583 5.365,3.802 0.333,0.219 10 false 48 5,2.656 5.458,2.917 0.458,0.26 10 false A62 5.042,2.49 5.375,2.729 0.333,0.24 10 false 52 5,3.385 5.448,3.698 0.448,0.313 10 false A62 5.052,3.208 5.479,3.49 0.427,0.281 10 false 50 5,4.115 5.406,4.417 0.406,0.302 10 false A62 5.042,3.938 5.354,4.115 0.313,0.177 10 false 51 5.802,7.448 6.177,7.667 0.375,0.219 10 false ECM 1.813,2.323 2.406,2.573 0.594,0.25 10 false VCPA 1.823,4.104 2.375,4.396 0.552,0.292 10 false EPA2 1.813,3.396 2.396,3.667 0.583,0.271 10 false VPA2 1.823,2.667 2.385,2.927 0.563,0.26 10 false VCP2 1.885,3.771 2.521,4.094 0.635,0.323 10 false EPA 1.885,3.031 2.438,3.281 0.552,0.25 10 false VPA 2.292,3.958 2.719,4.313 0.427,0.354 10 false 2 2.292,3.24 2.677,3.479 0.385,0.24 10 false 3 2.292,2.51 2.615,2.75 0.323,0.24 10 false 1 2.292,3.583 2.573,3.875 0.281,0.292 10 false 5 2.292,2.865 2.521,3.135 0.229,0.271 10 false 6 2.292,2.156 2.531,2.479 0.24,0.323 10 false 4 0.531,2.594 1.656,3.167 1.125,0.573 10 false Accelerator Pedal Sensor Assembly 0.542,2.438 1.094,2.74 0.552,0.302 10 false A6 1.99,0.719 2.406,0.979 0.417,0.26 10 false VC 2.01,1.073 2.385,1.354 0.375,0.281 10 false E2 1.906,1.427 2.385,1.729 0.479,0.302 10 false VTA 1.833,1.781 2.375,2.031 0.542,0.25 10 false VTA2 2.292,0.552 2.688,0.865 0.396,0.313 10 false 5 2.292,0.917 2.552,1.198 0.26,0.281 10 false 3 2.292,1.271 2.656,1.625 0.365,0.354 10 false 6 2.292,1.646 2.521,1.906 0.229,0.26 10 false 4 0.531,0.854 1.385,1.542 0.854,0.688 10 false Throttle Body Assembly 0.531,0.688 1.052,1 0.521,0.313 10 false B3 4.99,0.698 5.385,0.917 0.396,0.219 10 false B93 4.979,0.521 5.385,0.76 0.406,0.24 10 false 134 4.99,1.438 5.552,1.74 0.563,0.302 10 false B93 5,1.26 5.49,1.594 0.49,0.333 10 false 135 4.99,1.792 5.583,2.156 0.594,0.365 10 false B93 4.99,1.625 5.313,1.854 0.323,0.229 10 false 101 4.99,1.063 5.375,1.271 0.385,0.208 10 false B93 4.979,0.896 5.5,1.24 0.521,0.344 10 false 133 6.344,0.344 6.677,0.583 0.333,0.24 10 false 5 V 4.99,5.479 5.469,5.688 0.479,0.208 10 false B93 5,4.75 5.438,5.063 0.438,0.313 10 false B93 5,5.104 5.417,5.333 0.417,0.229 10 false B93 4.99,6.938 5.396,7.198 0.406,0.26 10 false B93 4.99,6.219 5.438,6.469 0.448,0.25 10 false B93 5,6.583 5.5,6.802 0.5,0.219 10 false B93 0.51,6 0.885,6.385 0.375,0.385 10 false B41 0.5,6.156 1.76,6.813 1.26,0.656 10 false Camshaft Position Sensor (for Exhaust Camshaft) 5.344,6.938 5.719,7.125 0.375,0.188 10 false EV1+ 5.344,6.49 5.802,6.781 0.458,0.292 10 false EV1- 5.031,6.771 5.396,7.021 0.365,0.25 10 false 80 5,6.406 5.427,6.625 0.427,0.219 10 false 112 5.333,5.479 5.906,5.74 0.573,0.26 10 false VV1+ 2.292,6.427 2.552,6.708 0.26,0.281 10 false 2 2.292,6.771 2.625,7.073 0.333,0.302 10 false 1 2.292,6.063 2.698,6.396 0.406,0.333 10 false 3 2.292,5.021 2.448,5.25 0.156,0.229 10 false 2 2.292,5.396 2.698,5.719 0.406,0.323 10 false 1 2.292,4.594 2.552,4.927 0.26,0.333 10 false 3 5.323,6.125 5.875,6.396 0.552,0.271 10 false VCE1 4.99,6.042 5.375,6.25 0.385,0.208 10 false 111 5.042,5.292 5.365,5.5 0.323,0.208 10 false 82 5,4.927 5.417,5.177 0.417,0.25 10 false 115 5,4.563 5.521,4.885 0.521,0.323 10 false 116 5.323,5.01 5.792,5.229 0.469,0.219 10 false VV1- 5.323,4.635 5.875,4.875 0.552,0.24 10 false VCV1 0.5,4.563 1.021,4.885 0.521,0.323 10 false B39 0.5,4.729 1.646,5.344 1.146,0.615 10 false Camshaft Position Sensor (for Intake Camshaft) 1.854,5.479 2.354,5.781 0.5,0.302 10 false VVI+ 1.885,5.094 2.448,5.396 0.563,0.302 10 false VVI- 1.969,4.74 2.302,4.99 0.333,0.25 10 false VC 1.813,6.927 2.417,7.24 0.604,0.313 10 false VVE+ 1.844,6.563 2.583,6.781 0.74,0.219 10 false VVE- 1.906,6.208 2.406,6.417 0.5,0.208 10 false VC2

A318634E05
5.854,5.146 6.24,5.438 0.385,0.292 10 false ECM 0.563,0.938 1.792,1.406 1.229,0.469 10 false Crankshaft Position Sensor 5.375,3.729 5.938,3.927 0.563,0.198 10 false VCPT* 0.521,4.063 1.938,4.365 1.417,0.302 10 false Oil Pressure Sensor*3 0.531,3.865 0.833,4.052 0.302,0.188 10 false B32 0.563,2.417 1.677,3 1.115,0.583 10 false Manifold Absolute Pressure Sensor 5.031,0.76 5.302,0.906 0.271,0.146 10 false B93 5.083,0.583 5.406,0.76 0.323,0.177 10 false 81 2.021,3.875 2.281,4.083 0.26,0.208 10 false VC 2.031,4.229 2.458,4.417 0.427,0.188 10 false E2 1.927,4.583 2.25,4.802 0.323,0.219 10 false PTO 2.313,4.146 2.729,4.344 0.417,0.198 10 false 1 2.333,4.5 2.75,4.698 0.417,0.198 10 false 2 2.313,3.781 2.51,3.979 0.198,0.198 10 false 3 0.563,2.25 0.865,2.438 0.302,0.188 10 false B45 2.01,2.323 2.271,2.531 0.26,0.208 10 false VC 2.01,0.75 2.271,0.958 0.26,0.208 10 false VC 2.042,2.688 2.469,2.875 0.427,0.188 10 false E2 5.365,1.031 5.792,1.219 0.427,0.188 10 false NE- 1.969,3.042 2.292,3.26 0.323,0.219 10 false PIM 1.938,1.479 2.26,1.698 0.323,0.219 10 false NE+ 1.104,0.76 1.583,0.948 0.479,0.188 10 false B88*2 2.323,0.667 2.521,0.865 0.198,0.198 10 false 1 2.323,2.24 2.521,2.438 0.198,0.198 10 false 3 2.323,1.031 2.74,1.229 0.417,0.198 10 false 2 2.323,2.583 2.74,2.781 0.417,0.198 10 false 1 2.323,2.948 2.74,3.146 0.417,0.198 10 false 2 2.333,1.396 2.75,1.594 0.417,0.198 10 false 3 5.385,4.604 5.979,4.885 0.594,0.281 10 false PTO* 5.396,4.115 5.938,4.375 0.542,0.26 10 false EPTO* 5.031,1.125 5.302,1.271 0.271,0.146 10 false B93 5.042,1.479 5.313,1.625 0.271,0.146 10 false B93 5.031,2.323 5.302,2.469 0.271,0.146 10 false B93 5.031,2.688 5.302,2.833 0.271,0.146 10 false B93 5.031,3.052 5.302,3.198 0.271,0.146 10 false B93 5.031,3.865 5.302,4.01 0.271,0.146 10 false B93 5.031,4.229 5.302,4.375 0.271,0.146 10 false B93 5.031,4.583 5.302,4.729 0.271,0.146 10 false B93 5.365,3.052 5.688,3.271 0.323,0.219 10 false PIM 5.354,2.573 5.938,2.792 0.583,0.219 10 false EPIM 5.365,2.208 5.896,2.438 0.531,0.229 10 false VCPM 1.948,1.115 2.375,1.302 0.427,0.188 10 false NE- 5.375,1.479 5.698,1.698 0.323,0.219 10 false NE+ 5.365,0.656 5.875,0.865 0.51,0.208 10 false VCNE 5.031,0.958 5.354,1.135 0.323,0.177 10 false 113 5.031,1.323 5.354,1.5 0.323,0.177 10 false 114 5.073,2.146 5.396,2.323 0.323,0.177 10 false 77 5.073,2.531 5.396,2.708 0.323,0.177 10 false 76 5.063,2.885 5.385,3.063 0.323,0.177 10 false 78 5.042,3.688 5.365,3.865 0.323,0.177 10 false 110 5.031,4.073 5.354,4.25 0.323,0.177 10 false 109 5.073,4.427 5.396,4.604 0.323,0.177 10 false 79 3.75,3.74 3.948,3.938 0.198,0.198 10 false *3 3.76,4.104 4,4.281 0.24,0.177 10 false *3 3.76,4.49 4,4.667 0.24,0.177 10 false *3 4.104,4.99 6.115,5.333 2.01,0.344 10 false *3: for CVT Models 0.542,0.76 1.458,0.958 0.917,0.198 10 false B106*1 0.052,5.021 7.156,5.219 7.104,0.198 10 false *1: for Manual Transaxle Models, w/ Stop and Start System 0.052,5.323 7.156,5.521 7.104,0.198 10 false *2: except Manual Transaxle Models, w/ Stop and Start System

PROCEDURE

1.CHECK MIL CONDITION
a.

Check that the Malfunction Indicator Lamp (MIL) lights up when the ignition switch is turned to ON.

OK:

MIL lights up.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK CONNECTION BETWEEN GTS AND ECM
2.CHECK CONNECTION BETWEEN GTS AND ECM
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check for communication between the GTS and ECM.

Result:
Result Proceed to
Communication is not possible A
Communication is possible B




A

3.CHECK MIL (THROTTLE POSITION SENSOR)

B

3.CHECK MIL (THROTTLE POSITION SENSOR)
a.

Disconnect the throttle body assembly connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B


HINT:

Perform "Inspection After Repair" after replacing the throttle body assembly (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




A

4.CHECK MIL (ACCELERATOR PEDAL SENSOR ASSEMBLY)

B

4.CHECK MIL (ACCELERATOR PEDAL SENSOR ASSEMBLY)
a.

Disconnect the accelerator pedal sensor assembly connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B




A

5.CHECK MIL (CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT))

B

REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

5.CHECK MIL (CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT))
a.

Disconnect the camshaft position sensor (for intake camshaft) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B




A

6.CHECK MIL (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT))

B

REPLACE CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT)

6.CHECK MIL (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT))
a.

Disconnect the camshaft position sensor (for exhaust camshaft) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B




A

7.CHECK MIL (CRANKSHAFT POSITION SENSOR)

B

REPLACE CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT)

7.CHECK MIL (CRANKSHAFT POSITION SENSOR)
a.

Disconnect the crankshaft position sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B




A

8.CHECK MIL (MANIFOLD ABSOLUTE PRESSURE SENSOR)

B

8.CHECK MIL (MANIFOLD ABSOLUTE PRESSURE SENSOR)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL does not illuminate (for CVT Models) A
MIL does not illuminate (for Manual Transaxle Models) B
MIL illuminates C




A

9.CHECK MIL (OIL PRESSURE SENSOR)

B

10.CHECK HARNESS AND CONNECTOR

C

9.CHECK MIL (OIL PRESSURE SENSOR)
a.

Disconnect the oil pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B




A

10.CHECK HARNESS AND CONNECTOR

B

10.CHECK HARNESS AND CONNECTOR
a.

Disconnect the throttle body assembly connector.


b.

Disconnect the accelerator pedal sensor assembly connector.


c.

Disconnect the camshaft position sensor (for intake camshaft) connector.


d.

Disconnect the camshaft position sensor (for exhaust camshaft) connector.


e.

Disconnect the crankshaft position sensor connector.


f.

Disconnect the manifold absolute pressure sensor connector.


g.

Disconnect the oil pressure sensor connector (for CVT Models).


h.

Disconnect the ECM connectors.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B93-134 (VCTA) - Body ground Always 10 kΩ or higher
A62-49 (VCPA) - Body ground Always 10 kΩ or higher
A62-52 (VCP2) - Body ground Always 10 kΩ or higher
B93-116 (VCV1) - Body ground Always 10 kΩ or higher
B93-111 (VCE1) - Body ground Always 10 kΩ or higher
B93-81 (VCNE) - Body ground Always 10 kΩ or higher
B93-77 (VCPM) - Body ground Always 10 kΩ or higher
B93-110 (VCPT)* - Body ground Always 10 kΩ or higher


*: for CVT Models


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR