Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) › from 2016.08
RM3090E _58 Vehicle Interior _008433 SEAT _0062871 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) J

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  Wireless Transmitter Memory Function does not Operate  


DESCRIPTION

With the ignition switch off and the driver door closed, pressing the manual lock or unlock switch on the multiplex network master switch assembly while holding a seat memory switch (M1 switch or M2 switch) will register the transmitter recognition code into the seat memory switch that was pressed. After registration is completed, the answer back buzzer sounds.

CAUTION / NOTICE / HINT

NOTICE:
·

The seat position will not be recorded if the SET switch and 2 of the seat memory switches are pressed simultaneously.

·

If a memorizing operation has failed, release all switches. The seat memory function does not operate unless the switches are released.

·

The front power seat control system (w/ Memory) uses the CAN communication system. First, confirm that there is no malfunction in the communication system by checking communication function of the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>HOW TO PROCEED WITH TROUBLESHOOTING

·

When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.



PROCEDURE

1.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

Check the manual lock/unlock function by using the door control switch (power window regulator master switch assembly).

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Manual lock/unlock function operates normally.



Result:
Result Proceed to
OK (w/ Entry and Start System) A
OK (w/o Entry and Start System) B
NG C



A

2.CHECK ENTRY AND START SYSTEM (for Start Function)

B

13.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM

C

2.CHECK ENTRY AND START SYSTEM (for Start Function)
a.

Check that the engine starts normally when the ignition switch is pressed with the brake pedal depressed and while carrying the key.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

3.CHECK SEAT POSITION MEMORY FUNCTION

NG

3.CHECK SEAT POSITION MEMORY FUNCTION

b.

Check that the buzzer sounds for 0.5 seconds to indicate that a position has been stored.

NOTICE:
·

The seat position will not be recorded if the SET switch and 2 of the seat memory switches are pressed simultaneously.

·

If a memorizing operation has failed, release all switches. The seat memory function does not operate unless the switches are released.



OK:

Seat position memory function operates normally.



Result:
Proceed to
OK
NG



OK

4.CHECK SEAT POSITION RESTORING FUNCTION

NG

GO TO OTHER DIAGNOSIS PROCEDURE (Power Seat Position is not Memorized)

4.CHECK SEAT POSITION RESTORING FUNCTION

b.

Check that the buzzer sounds for 0.1 seconds and the seat automatically moves to the memorized position.

NOTICE:
·

The seat will not return to the memorized position if 2 of the seat memory switches are pressed simultaneously.

·

If a restoring operation has failed, release all switches. The seat memory restoring function does not operate unless the switches are released.



OK:

Seat position restoring function operates normally.



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (DRIVER DOOR COURTESY SWITCH)

NG

GO TO OTHER DIAGNOSIS PROCEDURE (Power Seat does not Return to Memorized Position)

5.READ VALUE USING GTS (DRIVER DOOR COURTESY SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Door Courtesy SW Front door courtesy light switch assembly signal ON or OFF ON: Driver door open
OFF: Driver door closed
-
Body Electrical > Main Body > Data List
Tester Display
FR Door Courtesy SW
50003 123 197
OK:

ON or OFF appears on the screen according to the driver door condition.



Result:
Proceed to
OK
NG



OK

6.CHECK MEMORY CALL REGISTRATION FUNCTION

NG

GO TO LIGHTING SYSTEM (Courtesy Switch Circuit)

6.CHECK MEMORY CALL REGISTRATION FUNCTION
a.

When the following conditions are met, press the manual lock or unlock switch on the power window regulator master switch assembly.

·

Ignition switch is off

·

M1 or M2 seat memory switch is pressed and held

·

Driver door closed

·

Key is being carried



b.

Check that the buzzer sounds for 0.5 seconds to indicate the completion of memory call registration.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK


Result:
Result Proceed to
Buzzer sounds normally A
Buzzer does not sound normally B



A

7.READ VALUE USING GTS (MEMORY CALL REGISTRATION)

B

9.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
7.READ VALUE USING GTS (MEMORY CALL REGISTRATION)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Mem SW No. w/KeyID1 Memory switch linked with key ID1 NONE, MEM SW1, MEM SW2, or MEM SW3* NONE: No switches linked with key ID1
MEM SW1: M1 switch linked with key ID1
MEM SW2: M2 switch linked with key ID1
MEM SW3: M3 switch linked with key ID1*
-
Mem SW No. w/KeyID2 Memory switch linked with key ID2 NONE, MEM SW1, MEM SW2, or MEM SW3* NONE: No switches linked with key ID2
MEM SW1: M1 switch linked with key ID2
MEM SW2: M2 switch linked with key ID2
MEM SW3: M3 switch linked with key ID2*
-
Mem SW No. w/KeyID3 Memory switch linked with key ID3 NONE, MEM SW1, MEM SW2, or MEM SW3* NONE: No switches linked with key ID3
MEM SW1: M1 switch linked with key ID3
MEM SW2: M2 switch linked with key ID3
MEM SW3: M3 switch linked with key ID3*
-
Mem SW No. w/KeyID4 Memory switch linked with key ID4 NONE, MEM SW1, MEM SW2, or MEM SW3* NONE: No switches linked with key ID4
MEM SW1: M1 switch linked with key ID4
MEM SW2: M2 switch linked with key ID4
MEM SW3: M3 switch linked with key ID4*
-
Mem SW No. w/KeyID5 Memory switch linked with key ID5 NONE, MEM SW1, MEM SW2, or MEM SW3* NONE: No switches linked with key ID5
MEM SW1: M1 switch linked with key ID5
MEM SW2: M2 switch linked with key ID5
MEM SW3: M3 switch linked with key ID5*
-
Mem SW No. w/KeyID6 Memory switch linked with key ID6 NONE, MEM SW1, MEM SW2, or MEM SW3* NONE: No switches linked with key ID6
MEM SW1: M1 switch linked with key ID6
MEM SW2: M2 switch linked with key ID6
MEM SW3: M3 switch linked with key ID6*
-
Mem SW No. w/KeyID7 Memory switch linked with key ID7 NONE, MEM SW1, MEM SW2, or MEM SW3* NONE: No switches linked with key ID7
MEM SW1: M1 switch linked with key ID7
MEM SW2: M2 switch linked with key ID7
MEM SW3: M3 switch linked with key ID7*
-

*: Although the item is displayed on the GTS, it is not applicable to this vehicle.


Body Electrical > Main Body > Data List
Tester Display
Mem SW No. w/KeyID1
Mem SW No. w/KeyID2
Mem SW No. w/KeyID3
Mem SW No. w/KeyID4
Mem SW No. w/KeyID5
Mem SW No. w/KeyID6
Mem SW No. w/KeyID7
50003 123 185,186,187,188,189,190,191
OK:

On the GTS display, it is confirmed that the memory call has been registered.



Result:
Proceed to
OK
NG



OK

8.CHECK MEMORY CALL FUNCTION

NG

8.CHECK MEMORY CALL FUNCTION
a.

Turn the ignition switch off.


b.

Close and lock all doors.


c.

Unlock the driver door by pressing the unlock switch of the memory call registered key or touching the driver door outside handle while holding the memory call registered key.


d.

Open the driver door and check that the driver seat moves to the memorized position.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK


Result:
Result Proceed to
Driver seat moves to the memorized position A
Driver seat does not move to the memorized position B



A

B

GO TO OTHER DIAGNOSIS PROCEDURE (Wireless-linked Return Function does not Operate)

9.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

Result:
Proceed to
NEXT



NEXT

10.CHECK MEMORY CALL REGISTRATION FUNCTION
10.CHECK MEMORY CALL REGISTRATION FUNCTION
a.

When the following conditions are met, press the manual lock or unlock switch on the multiplex network master switch assembly.

·

Ignition switch is off

·

M1 or M2 seat memory switch is pressed and held

·

Driver door closed

·

Key is being carried



b.

Check that the buzzer sounds for 0.5 seconds to indicate the completion of memory call registration.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK


Result:
Result Proceed to
Buzzer sounds normally A
Buzzer does not sound normally B



A

END (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] WAS DEFECTIVE)

B

11.REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY
11.REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY
a.

Replace the position control ECU and switch assembly.

Click hereVehicle Interior>SEAT>POWER SEAT CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

12.CHECK MEMORY CALL REGISTRATION FUNCTION
12.CHECK MEMORY CALL REGISTRATION FUNCTION
a.

When the following conditions are met, press the manual lock or unlock switch on the multiplex network master switch assembly.

·

Ignition switch is off

·

M1 or M2 seat memory switch is pressed and held

·

Driver door closed

·

Key is being carried



b.

Check that the buzzer sounds for 0.5 seconds to indicate the completion of memory call registration.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK


Result:
Result Proceed to
Buzzer sounds normally A
Buzzer does not sound normally B



A

END (POSITION CONTROL ECU AND SWITCH ASSEMBLY WAS DEFECTIVE)

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

13.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check that the wireless door lock/unlock operates normally.

OK:

Wireless door lock/unlock operates normally.



Result:
Proceed to
OK
NG



OK

3.CHECK SEAT POSITION MEMORY FUNCTION

NG