When either the M1 or M2 switch is pressed, the main body ECU (multiplex network body ECU) sends a switch signal to the seat memory switch via CAN communication. Then, the main body ECU (multiplex network body ECU) sends a recall request signal to the position control ECU and switch assembly. The position control ECU and switch assembly operates each motor to achieve each memorized position value.
The front power seat control system (w/ Memory) uses the CAN communication system. First, confirm that there is no malfunction in the communication system by checking communication function of the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>PROBLEM SYMPTOMS TABLE
When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.
Check that each function of the power seat operates normally by using the switches on the power seat switch.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
Each function of the power seat operates normally using the switches on the power seat switch.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Store a seat position in memory and check that the buzzer sounds to indicate that a position has been stored.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
The seat position will not be recorded if the SET switch and 2 of the memory switches are pressed simultaneously.
If a memorizing operation has failed, release all switches. The seat memory function does not operate unless the switches are released.
| Result | Proceed to |
|---|---|
| Seat position memory function is normal | A |
| Seat position memory function is not normal | B |
A
B
Under each of the following conditions, check that the seat position restoring function operates by pressing the M1 switch or M2 switch.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
Ignition switch is off.
The ignition switch is ON, and the shift lever is in P (except Manual Transaxle) or Neutral position (for Manual Transaxle).*1
The ignition switch is turned off within 180 seconds after the driver door is closed and opened.*2
The ignition switch is turned off within 60 seconds after the driver door is opened and closed.*3
| Result | Proceed to |
|---|---|
| Seat position restoring function does not operate at all. | A |
| Seat position restoring function does not operate when the condition is *1 (except Manual Transaxle). | B |
| Seat position restoring function does not operate when the condition is *1 (for Manual Transaxle). | C |
·
Seat position restoring function does not operate when the condition is *2. ·
Seat position restoring function does not operate when the condition is *3. |
D |
A
B
C
D
Store a seat position in memory for each of the M1 and M2 switches.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Driver Seat / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Seat Memory No1 | Seat position memorized with M1 switch | Mem or Not Mem | Mem: Memorized
Not Mem: Not memorized |
- |
| Seat Memory No2 | Seat position memorized with M2 switch | Mem or Not Mem | Mem: Memorized
Not Mem: Not memorized |
- |
| Tester Display |
|---|
| Seat Memory No1 |
| Seat Memory No2 |
Mem appears on the GTS screen.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the seat memory switch.
| Proceed to |
|---|
| NEXT |
NEXT
Restore a memorized seat position.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
Check that the buzzer sounds for 0.1 seconds and the seat automatically moves to the memorized position.
The seat will not return to the memorized position if 2 of the seat memory switches are pressed simultaneously.
If a restoring operation has failed, release all switches. The seat memory restoring function does not operate unless the switches are released.
| Result | Proceed to |
|---|---|
| Seat position restoring function operates normally | A |
| Seat position restoring function does not operate normally | B |
A
B
Replace the position control ECU and switch assembly.
Click hereVehicle Interior>SEAT>POWER SEAT CONTROL ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Store a seat position in memory.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
Restore a memorized seat position.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
Check that the buzzer sounds for 0.1 seconds and the seat automatically moves to the memorized position.
The seat will not return to the memorized position if 2 of the seat memory switches are pressed simultaneously.
If a restoring operation has failed, release all switches. The seat memory restoring function does not operate unless the switches are released.
| Result | Proceed to |
|---|---|
| Seat position restoring function operates normally | A |
| Seat position restoring function does not operate normally | B |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Driver Seat / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| P Switch | Park state signal | ON or OFF | ON: Shift lever in P
OFF: Shift lever in a position other than P |
- |
| Tester Display |
|---|
| P Switch |
On the GTS screen, the item changes between ON and OFF according to the above.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for Automatic Transaxle) | B |
| NG (for CVT) | C |
A
B
C
Remove the back-up light switch assembly.
Inspect the back-up light switch assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Door Courtesy SW | Front door courtesy light switch assembly signal | ON or OFF | ON: Driver door open
OFF: Driver door closed |
- |
| Tester Display |
|---|
| FR Door Courtesy SW |
On the GTS screen, the item changes between ON and OFF according to the above.
| Proceed to |
|---|
| OK |
| NG |
OK
NG