Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.08
RM3090E _54 Brake _008767 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0048751 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1407  Open or Short in Rear Speed Sensor RH Circuit  C1408  Open or Short in Rear Speed Sensor LH Circuit  


DESCRIPTION

Refer to DTCs C1403 and C1404.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1403

DTC No. Detection Item DTC Detection Condition Trouble Area
C1407 Open or Short in Rear Speed Sensor RH Circuit Either of the following is detected:
1.

An open in the speed sensor signal circuit continues for 0.5 seconds or more.

2.

With the +BS terminal voltage at 9.5 V or higher, the sensor power supply voltage decreases for 0.5 seconds or more.


·

Rear speed sensor RH (for 4WD/AWD)

·

Rear speed sensor RH (Rear axle hub and bearing assembly RH) (for 2WD)

·

Skid control sensor wire RH

·

Skid control ECU (Brake actuator assembly)

·

Wire harness or connector


C1408 Open or Short in Rear Speed Sensor LH Circuit Either of the following is detected:
1.

An open in the speed sensor signal circuit continues for 0.5 seconds or more.

2.

With the +BS terminal voltage at 9.5 V or higher, the sensor power supply voltage decreases for 0.5 seconds or more.


·

Rear speed sensor LH (for 4WD/AWD)

·

Rear speed sensor LH (Rear axle hub and bearing assembly LH) (for 2WD)

·

Skid control sensor wire LH

·

Skid control ECU (Brake actuator assembly)

·

Wire harness or connector



WIRING DIAGRAM

C271651E09
0.438,2.021 1.938,2.635 1.5,0.615 10 false Rear Speed Sensor RH (Rear Axle Hub and Bearing Assembly RH) 4.01,0.115 4.198,0.302 0.188,0.188 10 false 1 2.833,0.115 2.948,0.281 0.115,0.167 10 false 2 0.469,0.469 1.958,1.104 1.49,0.635 10 false Rear Speed Sensor LH (Rear Axle Hub and Bearing Assembly LH) 2.823,2.198 2.969,2.375 0.146,0.177 10 false 1 4.031,2.24 4.146,2.406 0.115,0.167 10 false 2 5.396,3.052 7,3.51 1.604,0.458 10 false Skid Control ECU (Brake Actuator Assembly) 5.833,0.74 6.073,1 0.24,0.26 10 false 28 6.125,1.875 6.448,2.021 0.323,0.146 10 false RR+ 5.833,0.198 6.156,0.469 0.323,0.271 10 false 29 6.135,2.417 6.427,2.563 0.292,0.146 10 false RR- 5.844,2.333 6.094,2.531 0.25,0.198 10 false 15 6.094,0.333 6.448,0.479 0.354,0.146 10 false RL+ 5.844,1.781 6.104,1.969 0.26,0.188 10 false 16 6.104,0.875 6.354,1.021 0.25,0.146 10 false RL- 2.802,0.333 3.042,0.5 0.24,0.167 10 false n1 2.771,1.875 3.042,2.042 0.271,0.167 10 false m1 5.438,2.833 5.865,3.021 0.427,0.188 10 false A100 2.844,0.656 2.99,0.823 0.146,0.167 10 false 1 4.021,0.667 4.167,0.823 0.146,0.156 10 false 2 4.031,1.688 4.146,1.854 0.115,0.167 10 false 1 2.823,1.646 2.938,1.813 0.115,0.167 10 false 2 2.792,0.875 3.021,1.042 0.229,0.167 10 false n1 3.938,0.333 4.271,0.531 0.333,0.198 10 false nN1 3.927,1.875 4.26,2.073 0.333,0.198 10 false mM1 2.906,2.833 4.823,3.052 1.917,0.219 10 false Skid Control Sensor Wire RH 3,1.188 4.917,1.406 1.917,0.219 10 false Skid Control Sensor Wire LH 3.948,0.885 4.281,1.083 0.333,0.198 10 false nN1 2.76,2.458 3.031,2.625 0.271,0.167 10 false m1 3.917,2.448 4.25,2.646 0.333,0.198 10 false mM1 0.094,0.083 0.854,0.302 0.76,0.219 12 false for 2WD: 2.563,0.313 2.708,0.49 0.146,0.177 10 false + 2.583,0.854 2.698,1.042 0.115,0.188 10 false - 2.542,1.896 2.677,2.083 0.135,0.188 10 false + 2.563,2.427 2.677,2.615 0.115,0.188 10 false -

C241007E51
0.385,2.219 1.24,2.625 0.854,0.406 10 false Rear Speed Sensor RH 2.302,0.635 2.458,0.802 0.156,0.167 10 false 1 2.302,1.104 2.417,1.292 0.115,0.188 10 false 2 0.344,1.021 1.167,1.427 0.823,0.406 10 false Rear Speed Sensor LH 2.292,1.833 2.438,1.99 0.146,0.156 10 false 1 2.313,2.313 2.427,2.479 0.115,0.167 10 false 2 5,3.104 6.552,3.479 1.552,0.375 10 false Skid Control ECU (Brake Actuator Assembly) 5.26,1.146 5.5,1.396 0.24,0.25 10 false 28 5.552,1.979 5.844,2.125 0.292,0.146 10 false RR+ 5.271,0.656 5.521,0.875 0.25,0.219 10 false 29 5.573,2.448 5.865,2.594 0.292,0.146 10 false RR- 5.24,2.344 5.49,2.563 0.25,0.219 10 false 15 5.563,0.781 5.885,0.958 0.323,0.177 10 false RL+ 5.24,1.854 5.521,2.104 0.281,0.25 10 false 16 5.583,1.26 5.833,1.406 0.25,0.146 10 false RL- 0.365,0.781 0.729,0.948 0.365,0.167 10 false N11 0.406,2.031 0.771,2.198 0.365,0.167 10 false M20 5.021,2.906 5.583,3.083 0.563,0.177 9 false A100 1.885,0.771 2.219,0.948 0.333,0.177 10 false RL+ 1.885,1.25 2.156,1.406 0.271,0.156 10 false RL- 1.875,1.958 2.167,2.104 0.292,0.146 10 false RR+ 1.927,2.448 2.219,2.594 0.292,0.146 10 false RR- 0.125,0.063 1.594,0.302 1.469,0.24 12 false for 4WD/AWD:

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

Disassembly of the rear speed sensor from the rear axle hub and bearing assembly is prohibited (for 2WD).



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS


Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Speed Open Rear speed sensor RH open detection Normal or Error Normal Error: Momentary interruption
RL Speed Open Rear speed sensor LH open detection Normal or Error Normal Error: Momentary interruption
Chassis > ABS/VSC/TRC > Data List
Tester Display
RR Speed Open
RL Speed Open
50003 105 202,203
OK:

Normal (There are no momentary interruptions.)


HINT:

Perform the above inspection before removing the sensor and connector.


Result:
Proceed to
OK
NG (for 2WD)
NG (for 4WD/AWD)



OK

2.READ VALUE USING GTS (REAR SPEED SENSOR)

NG (for 2WD)

4.INSPECT SKID CONTROL SENSOR WIRE

NG (for 4WD/AWD)

5.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR SPEED SENSOR)
2.READ VALUE USING GTS (REAR SPEED SENSOR)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Start the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


f.

According to the display on the GTS, read the Data List.


Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed:
No large fluctuations
RL Wheel Speed Rear wheel speed sensor LH reading Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed:
No large fluctuations
Chassis > ABS/VSC/TRC > Data List
Tester Display
RR Wheel Speed
RL Wheel Speed
50003 105 3,4
g.

Check that there is no difference between the speed value output from the speed sensor displayed on the GTS and the speed value displayed on the speedometer when driving the vehicle.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK


OK:

The speed value output from the speed sensor displayed on the GTS is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE


HINT:
·

The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.

If the rear speed sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly with rear speed sensor.

·

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




Result:
Proceed to
OK
NG (for 2WD)
NG (for 4WD/AWD)



OK

3.RECONFIRM DTC

NG (for 2WD)

4.INSPECT SKID CONTROL SENSOR WIRE

NG (for 4WD/AWD)

5.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR SPEED SENSOR)
3.RECONFIRM DTC

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105
b.

Turn the ignition switch off.


c.

Start the engine.


d.

Perform a road test.



Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Proceed to
DTCs C1407 and C1408 are not output
DTCs C1407 and/or C1408 are output



DTCs C1407 and C1408 are not output

DTCs C1407 and/or C1408 are output

4.INSPECT SKID CONTROL SENSOR WIRE
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

for RH:

Disconnect the m1 and mM1 skid control sensor wire connectors.


d.

for LH:

Disconnect the n1 and nN1 skid control sensor wire connectors.


e.
C251359C05
0.771,0.698 1.083,0.948 0.313,0.25 0.771,0.958 1.083,1.208 0.313,0.25 2.229,0.698 2.594,0.969 0.365,0.271 2.24,0.979 2.583,1.229 0.344,0.25 0.552,2.823 0.833,1.979 false 1.094,1.99 1.375,2.813 false 0.281,0.219 0.719,0.563 0.438,0.344 10 false *a 0.833,0.74 1.146,0.938 0.313,0.198 10 false m1 0.854,0.99 1.167,1.188 0.313,0.198 10 false n1 2.271,0.76 2.729,0.958 0.458,0.198 10 false mM1 2.292,1.021 2.75,1.219 0.458,0.198 10 false nN1 2.365,1.271 2.677,1.469 0.313,0.198 10 false *c 0.875,1.271 1.188,1.469 0.313,0.198 10 false *b 1.229,0.75 1.542,0.948 0.313,0.198 10 false *A 2.75,0.75 3.063,0.948 0.313,0.198 10 false *A 1.229,1.031 1.542,1.229 0.313,0.198 10 false *B 2.75,1.031 3.063,1.229 0.313,0.198 10 false *B 1.375,2.813 2.146,3.01 0.771,0.198 10 false + 0.51,2.833 0.625,3 0.115,0.167 10 false -
*A for RH
*B for LH
*a Front view of Skid Control Sensor Wire
*b Front view of wire harness connector
(to Sensor Side Connector)
*c Front view of wire harness connector
(to Vehicle Side Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH:
Tester Connection Condition Specified Condition
m1-2 (+) - mM1-1 Always Below 1 Ω
m1-1 (-) - mM1-2 Always Below 1 Ω
m1-2 (+) - mM1-2 Always 10 kΩ or higher
m1-2 (+) or mM1-1 - Body ground Always 10 kΩ or higher
m1-1 (-) - mM1-1 Always 10 kΩ or higher
m1-1(-) or mM1-2 - Body ground Always 10 kΩ or higher

for LH:
Tester Connection Condition Specified Condition
n1-2 (+) - nN1-1 Always Below 1 Ω
n1-1 (-) - nN1-2 Always Below 1 Ω
n1-2 (+) - nN1-2 Always 10 kΩ or higher
n1-2 (+) or nN1-1 - Body ground Always 10 kΩ or higher
n1-1 (-) - nN1-1 Always 10 kΩ or higher
n1-1 (-) or nN1-2 - Body ground Always 10 kΩ or higher


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR SPEED SENSOR)

NG

5.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR SPEED SENSOR)
a.

for 2WD:

i.

Reconnect the mM1 (for RH) or nN1 (for LH) skid control sensor wire connector.


ii.

Turn the ignition switch off.


iii.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


iv.

Disconnect the A100 skid control ECU (brake actuator assembly) connector.


v.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A100-16 (RR+) - m1-2 (+) Always Below 1 Ω
A100-15 (RR-) - m1-1 (-) Always Below 1 Ω
A100-16 (RR+) or m1-2(+) - Body ground Always 10 kΩ or higher
A100-15 (RR-) or m1-1 (-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A100-29 (RL+) - n1-2 (+) Always Below 1 Ω
A100-28 (RL-) - n1-1 (-) Always Below 1 Ω
A100-29 (RL+) or n1-2 (+) - Body ground Always 10 kΩ or higher
A100-28 (RL-) or n1-1 (-) - Body ground Always 10 kΩ or higher




b.

for 4WD/AWD:

i.

Turn the ignition switch off.


ii.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


iii.

Disconnect the A100 skid control ECU (brake actuator assembly) connector and the N11 and/or M20 rear speed sensor connector.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A100-16 (RR+) - M20-1 (RR+) Always Below 1 Ω
A100-15 (RR-) - M20-2 (RR-) Always Below 1 Ω
A100-16 (RR+) or M20-1(RR+) - Body ground Always 10 kΩ or higher
A100-15 (RR-) or M20-2 (RR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A100-29 (RL+) - N11-1 (RL+) Always Below 1 Ω
A100-28 (RL-) - N11-2 (RL-) Always Below 1 Ω
A100-29 (RL+) or N11-1 (RL+) - Body ground Always 10 kΩ or higher
A100-28 (RL-) or N11-2 (RL-) - Body ground Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

6.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT)
a.

for 2WD:

i.

Reconnect the A100 skid control ECU (brake actuator assembly) connector.


ii.

Turn the ignition switch to ON.


iii.
C233859C02
0.646,0.521 1.135,0.813 0.49,0.292 2,0.521 2.49,0.813 0.49,0.292 0.969,1.344 1.177,1.781 false 2.323,1.344 2.531,1.781 false 1.146,1.792 1.51,2.01 0.365,0.219 10 false + 2.49,1.792 2.917,2 0.427,0.208 10 false + 0.135,0.083 0.323,0.24 0.188,0.156 10 false *a 0.76,0.573 1.052,0.729 0.292,0.156 10 false m1 2.135,0.573 2.427,0.729 0.292,0.156 10 false n1 0.771,0.302 1.083,0.5 0.313,0.198 10 false *A 2.094,0.323 2.406,0.521 0.313,0.198 10 false *B
*A for RH
*B for LH
*a Front view of wire harness connector
(to Rear Speed Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Switch Condition Specified Condition
m1-2 (+) - Body ground Ignition switch ON 8 to 14 V

for LH
Tester Connection Switch Condition Specified Condition
n1-2 (+) - Body ground Ignition switch ON 8 to 14 V


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE


HINT:

The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.

If the rear speed sensor rotor needs to be replaced, replace the rear axle hub and bearing assembly with rear speed sensor.




b.

for 4WD/AWD:

i.

Reconnect the A100 skid control ECU (brake actuator assembly) connector.


ii.

Turn the ignition switch to ON.


iii.
C279422C01
0.667,0.302 1.083,0.563 0.417,0.26 2.313,0.313 2.677,0.573 0.365,0.26 1.042,1.094 1.219,1.74 false 2.656,1.75 2.531,1.115 false 2.375,0.354 2.833,0.552 0.458,0.198 10 false N11 0.75,0.354 1.208,0.552 0.458,0.198 10 false M20 1.156,1.802 1.615,2 0.458,0.198 10 false RR+ 2.563,1.813 3.021,2.01 0.458,0.198 10 false RL+ 0.781,0.073 1.094,0.271 0.313,0.198 10 false *A 2.396,0.083 2.708,0.281 0.313,0.198 10 false *B
*A for RH
*B for LH
*a Front view of wire harness connector
(to Rear Speed Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Switch Condition Specified Condition
M20-1 (RR+) - Body ground Ignition switch ON 8 to 14 V

for LH
Tester Connection Switch Condition Specified Condition
N11-1 (RL+) - Body ground Ignition switch ON 8 to 14 V


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE




Result:
Proceed to
OK (for 2WD)
OK (for 4WD/AWD)
NG



OK (for 2WD)

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY

OK (for 4WD/AWD)

NG