Refer to TRC OFF Indicator Light Remains ON.
Refer to TRC OFF Indicator Light Remains ON.
When replacing the brake actuator assembly, perform zero point calibration.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION
Check if CAN communication system DTCs are output.
for LHD with Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM
for RHD with Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM
for LHD without Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU)>DIAGNOSIS SYSTEM
for RHD without Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD without Central Gateway ECU)>DIAGNOSIS SYSTEM
| Proceed to |
|---|
| DTC is not output |
| DTC is output (for LHD with Central Gateway ECU) |
| DTC is output (for RHD with Central Gateway ECU) |
| DTC is output (for LHD without Central Gateway ECU) |
| DTC is output (for RHD without Central Gateway ECU) |
DTC is not output
DTC is output (for LHD with Central Gateway ECU)
DTC is output (for RHD with Central Gateway ECU)
DTC is output (for LHD without Central Gateway ECU)
DTC is output (for RHD without Central Gateway ECU)
Turn the ignition switch off.
Disconnect the A100 skid control ECU (brake actuator assembly) connector.
| *a | Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly]) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A100-33 (CSW) - Body ground | VSC OFF switch (telltale light assembly) held on | Below 1 Ω |
| VSC OFF switch (telltale light assembly) off (Not pressed) | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the A100 skid control ECU (brake actuator assembly) connector.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| TRC/VSC Off Mode | TRC/TRAC/VSC off mode | Normal, TRC OFF or VSC OFF | Normal: Normal mode
TRC OFF: TRC/TRAC off mode VSC OFF: VSC off mode |
- |
| Tester Display |
|---|
| TRC/VSC Off Mode |
Check that the mode display changes according to the VSC OFF switch (telltale light assembly) operation.
Display changes according to the switch operation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for Segment Display Type:
Perform Active Test of the combination meter assembly using the GTS.
| Tester Display |
|---|
| VSC TRC Indicator |
Check the combination meter assembly.
The TRC/TRAC OFF indicator light turns on or off in accordance with the GTS.
for TFT Display Type:
Perform Active Test of the combination meter assembly using the GTS.
| Tester Display |
|---|
| Meter Display 1 |
Check the combination meter assembly.
The multi-information display turns on or off in accordance with the GTS operation
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Remove the VSC OFF switch (telltale light assembly).
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VSC OFF SWITCH>REMOVAL
Inspect the VSC OFF switch (telltale light assembly).
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VSC OFF SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A100-33 (CSW) - G43-6 (+) | Always | Below 1 Ω |
| G43-13 (E) - Body ground | Always | Below 1 Ω |
| A100-33 (CSW) or G43-6 (+) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG