The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.
for Segment Display Type:
Pressing the VSC OFF switch (telltale light assembly) turns off traction control and pressing and holding this switch turns off traction and VSC controls. If traction control turns OFF, the TRC/TRAC OFF indicator light will come on.
If VSC and traction control turns OFF, the TRC/TRAC OFF indicator and VSC OFF indicator light will come on.
The TRC/TRAC OFF indicator light is illuminated when the TRC/TRAC control is prohibited by operating the VSC OFF switch (telltale light assembly).
By pressing the VSC OFF switch (telltale light assembly) for a short time, the TRC/TRAC OFF mode is activated, and the TRC/TRAC control is prohibited, and the TRC/TRAC OFF indicator light in the combination meter is illuminated.
By pressing the VSC OFF switch (telltale light assembly) for 3 seconds or more, the VSC OFF mode is activated, the VSC and TRC/TRAC controls are prohibited, and both the VSC OFF indicator light and the TRC/TRAC OFF indicator light are illuminated.
If there is a malfunction in the SFI system, the TRC/TRAC system will be prohibited and the TRC/TRAC OFF indicator light will turn on (for 2AR-FE, 3ZR-FE).
for TFT Display Type:
Pressing the VSC OFF switch (telltale light assembly) turns off traction control and pressing and holding this switch turns off traction and VSC controls. If traction control turns OFF, TRC OFF is displayed on the multi-information display.
If VSC and traction control turns OFF, TRC OFF is displayed on the multi-information display and the VSC OFF indicator light will come on.
TRC OFF is displayed on the multi-information display when the TRC control is prohibited by operating the VSC OFF switch (telltale light assembly).
By pressing the VSC OFF switch (telltale light assembly) for a short time, the TRC OFF mode is activated, TRC control is prohibited, and TRC OFF is displayed on the multi-information display.
By pressing the VSC OFF switch (telltale light assembly) for 3 seconds or more, the VSC OFF mode is activated, VSC and TRC controls are prohibited, the VSC OFF indicator light illuminates and TRC OFF is displayed on the multi-information display.
If there is a malfunction in the SFI system, the TRC system will be prohibited and the TRC OFF will be displayed on the multi-information display (for 2AR-FE, 3ZR-FE, 3ZR-FAE).
When replacing the skid control ECU (brake actuator assembly), perform zero point calibration.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION
Check the engine type.
| Result | Proceed to |
|---|---|
| 2AR-FE | A |
| 3ZR-FAE | |
| 3ZR-FE | |
| 2AD-FHV | B |
| 2AD-FTV | |
| 2WW |
A
B
Check if SFI system DTCs are output
for 2AR-FE (w/ Canister Pump Module): Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>DTC CHECK / CLEAR
for 2AR-FE (w/o Canister Pump Module): Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>DTC CHECK / CLEAR
for 3ZR-FAE: Click hereEngine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
for 3ZR-FE (for K111, K111F): Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>SFI SYSTEM(for K111, K111F)>DTC CHECK / CLEAR
for 3ZR-FE (except K111, K111F): Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>SFI SYSTEM(except K111, K111F)>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTCs are not output |
| DTCs are output (for 2AR-FE (w/ Canister Pump Module)) |
| DTCs are output (for 2AR-FE (w/o Canister Pump Module)) |
| DTCs are output (for 3ZR-FAE) |
| DTCs are output (for K111, K111F) |
| DTCs are output (except K111, K111F) |
DTCs are not output
DTCs are output (for 2AR-FE (w/ Canister Pump Module))
DTCs are output (for 2AR-FE (w/o Canister Pump Module))
DTCs are output (for 3ZR-FAE)
Click hereEngine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
DTCs are output (for K111, K111F)
DTCs are output (except K111, K111F)
Check if the skid control ECU (brake actuator assembly) connector is securely connected.
The connector is securely connected.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check if CAN communication system DTCs are output.
for LHD with Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM
for RHD with Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM
for LHD without Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU)>DIAGNOSIS SYSTEM
for RHD without Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD without Central Gateway ECU)>DIAGNOSIS SYSTEM
| Proceed to |
|---|
| DTC is not output |
| DTC is output (for LHD with Central Gateway ECU) |
| DTC is output (for RHD with Central Gateway ECU) |
| DTC is output (for LHD without Central Gateway ECU) |
| DTC is output (for RHD without Central Gateway ECU) |
DTC is not output
DTC is output (for LHD with Central Gateway ECU)
DTC is output (for RHD with Central Gateway ECU)
DTC is output (for LHD without Central Gateway ECU)
DTC is output (for RHD without Central Gateway ECU)
Check the battery voltage.
11 to 14 V
| Proceed to |
|---|
| OK |
| NG (for 2AD-FHV) |
| NG (for 2AD-FTV) |
| NG (for 2AR-FE) |
| NG (for 3ZR-FAE) |
| NG (for 3ZR-FE) |
| NG (for 2WW) |
OK
NG (for 2AD-FHV)
NG (for 2AD-FTV)
NG (for 2AR-FE)
NG (for 3ZR-FAE)
NG (for 3ZR-FE)
NG (for 2WW)
Turn the ignition switch off.
Disconnect the A100 skid control ECU (brake actuator assembly) connector.
| *a | Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly]) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A100-33 (CSW) - Body ground | VSC OFF switch (telltale light assembly) held on | Below 1 Ω |
| VSC OFF switch (telltale light assembly) off (Not pressed) | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the A100 skid control ECU (brake actuator assembly) connector.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| TRC/VSC Off Mode | TRC/TRAC/VSC off mode | Normal, TRC OFF or VSC OFF | Normal: Normal mode
TRC OFF: TRC/TRAC off mode VSC OFF: VSC off mode |
- |
| Tester Display |
|---|
| TRC/VSC Off Mode |
Check that the mode display changes according to the VSC OFF switch (telltale light assembly) operation.
Display changes according to the switch operation.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Remove the VSC OFF switch (telltale light assembly).
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VSC OFF SWITCH>REMOVAL
Inspect the VSC OFF switch (telltale light assembly).
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VSC OFF SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A100-33 (CSW) - G43-6 (+) | Always | Below 1 Ω |
| G43-13 (E) - Body ground | Always | Below 1 Ω |
| A100-33 (CSW) or G43-6 (+) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG