Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.08
RM3090E _54 Brake _008767 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0048751 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  AUTO LSD Indicator Light does not Come ON  


CAUTION / NOTICE / HINT

NOTICE:

When replacing the brake actuator assembly, perform zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM

Result:
Proceed to
DTC is not output
DTC is output (for LHD with Central Gateway ECU)
DTC is output (for RHD with Central Gateway ECU)
DTC is output (for LHD without Central Gateway ECU)
DTC is output (for RHD without Central Gateway ECU)



DTC is not output

2.CHECK HARNESS AND CONNECTOR (CSW TERMINAL)

DTC is output (for LHD with Central Gateway ECU)

DTC is output (for RHD with Central Gateway ECU)

DTC is output (for LHD without Central Gateway ECU)

DTC is output (for RHD without Central Gateway ECU)

2.CHECK HARNESS AND CONNECTOR (CSW TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the A100 skid control ECU (brake actuator assembly) connector.


c.
C365682C08
1.5,0.135 1.958,0.344 0.458,0.208 1.719,1.917 1.719,1.771 1.719,1.771 1.938,1.292 true 0.094,0.042 0.406,0.24 0.313,0.198 10 false *a 1.563,0.156 1.979,0.354 0.417,0.198 10 false A100 1.573,1.969 2.021,2.167 0.448,0.198 10 false CSW
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A100-33 (CSW) - Body ground VSC OFF switch (telltale light assembly) held on Below 1 Ω
VSC OFF switch (telltale light assembly) (Not pressed) 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING GTS (AUTO LSD INDICATOR LIGHT)

NG

5.INSPECT TELLTALE LIGHT ASSEMBLY
3.PERFORM ACTIVE TEST USING GTS (AUTO LSD INDICATOR LIGHT)
a.

Reconnect the A100 skid control ECU (brake actuator assembly) connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.


f.

According to the display on the GTS, perform the Active Test.


Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Auto LSD Indicator Light AUTO LSD indicator light Indicator light ON/OFF for 2WD
Observe combination meter
Vehicle condition: Vehicle stopped
g.

When performing the AUTO LSD Indicator Light Active Test, check AUTO LSD Indicator Light in the Data List.


Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Auto LSD Indicator Light AUTO LSD indicator light ON or OFF OFF: AUTO LSD indicator light off
ON: AUTO LSD indicator light on
for 2WD
Chassis > ABS/VSC/TRC > Active Test
Active Test Display
Auto LSD Indicator Light
Data List Display
Auto LSD Indicator Light
50004 105 88 334
Result:
Result Proceed to
AUTO LSD indicator light in the Data List does not change using the Active Test A
AUTO LSD indicator light in the Data List turns ON/OFF using the Active Test B



A

B

4.INSPECT COMBINATION METER ASSEMBLY
4.INSPECT COMBINATION METER ASSEMBLY
a.

Turn the ignition switch off.


b.

Perform Active Test of the combination meter assembly using the GTS.


Body Electrical > Combination Meter > Active Test
Tester Display
Indicat. Auto LSD
50004 122 50
c.

Check the combination meter assembly.


OK:

The AUTO LSD indicator light turns on or off in accordance with the GTS.


Result:
Proceed to
OK
NG



OK

NG

5.INSPECT TELLTALE LIGHT ASSEMBLY
a.

Remove the VSC OFF switch (telltale light assembly).

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VSC OFF SWITCH>REMOVAL


b.

Inspect the VSC OFF switch (telltale light assembly).

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VSC OFF SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - TELLTALE LIGHT ASSEMBLY)

NG

6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - TELLTALE LIGHT ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A100-33 (CSW) - G43-6 (+) Always Below 1 Ω
G43-13 (E) - Body ground Always Below 1 Ω
A100-33 (CSW) or G43-6 (+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR