When the electrical key transmitter sub-assembly is in the cabin and the engine switch is pressed, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode. Additionally, when the shift state is park (P) and the brake pedal is depressed, the engine can be started by pressing the engine switch. If the steering is unlocked, the engine can also be started by pressing the engine switch with the shift state park (P) and the brake pedal depressed.
When the electrical key transmitter sub-assembly is in the cabin and the engine switch is pressed, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode. Additionally, when the clutch pedal is depressed, the engine can be started by pressing the engine switch. If the steering is unlocked, the engine can also be started by pressing the engine switch with the clutch pedal depressed.
| Problem Symptom | Data List and Active Test |
|---|---|
| Engine does not Start | Power Source Control
·
Stop Light Switch1*1 ·
Steering Unlock Switch ·
Shift P Signal Pulse*1 ·
IG Relay Monitor (Inside) ·
IG Relay Monitor (Outside) ·
Latch Circuit ·
Starter Request Signal ·
Power Supply Condition Entry&Start
·
Immobiliser ·
Engine Start Request ·
S Code Check*2 ·
L Code Check Starting Control
·
Starter SW ·
Shift Position Status*1 ·
Ignition |
*1: except Manual Transaxle
*2: w/o Occupant Classification System
w/ Stop and Start System
w/o Stop and Start System
When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
If the entry and start system (for Start Function) has been canceled, enable the system before performing troubleshooting.
Inspect the fuses of circuits related to this system before performing the following procedure.
Before replacing the certification ECU (smart key ECU assembly) or an electrical key transmitter sub-assembly, refer to the Service Bulletin.
After completing repairs, confirm that the problem does not recur.
After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
Check vehicle condition.
| Proceed to |
|---|
| for Manual Transaxle |
| except Manual Transaxle |
for Manual Transaxle
except Manual Transaxle
Get into the vehicle while carrying an electrical key transmitter sub-assembly.
With the clutch pedal released, check that pressing the engine switch causes the power source mode to change.
| Result | Proceed to |
|---|---|
| Power source mode changes: Off → on (ACC) → on (IG) → off | A |
| Power source mode does not change to on (ACC) or on (IG) | B |
| Power source mode changes to on (IG) but not to on (ACC) | C |
| Power source mode changes to on (ACC) but not to on (IG) | D |
A
B
C
D
Enter the following menus: Body Electrical / Power Source Control / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Neutral SW/ Clutch SW | State of clutch pedal | ON or OFF | ON: Clutch pedal depressed
OFF: Clutch pedal released |
·
Use this item to determine whether the clutch position switch is malfunctioning. ·
The engine cannot be started when this item is "OFF". |
| Tester Display |
|---|
| Neutral SW/ Clutch SW |
The GTS display changes correctly in response to the clutch pedal operation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Starter Request Signal | Engine start request signal status | OFF or ON | OFF: The engine switch is not pressed
ON: With the clutch pedal depressed, the engine switch is pressed and held |
·
When the engine cannot be started due to a start request signal malfunction, OFF is displayed. ·
When the engine switch is pressed, the duration of time that ON is displayed will be extremely short. As such, the engine switch needs to be pressed and held for a certain period of time. |
| Tester Display |
|---|
| Starter Request Signal |
Check that the key indicator display is displayed on the multi-information display in the combination meter assembly, and then press the engine switch.
The GTS display changes correctly in response to the engine switch operation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Get into the vehicle while carrying an electrical key transmitter sub-assembly.
Enter the following menus: Body Electrical / Starting Control / Data List.
Read the Data List while pressing the engine switch with the clutch pedal depressed according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Starter SW | Starter operation request | OFF or ON | OFF: Starter operation not requested
ON: Starter operation requested |
When OFF is displayed, the engine will not crank. |
| Tester Display |
|---|
| Starter SW |
The GTS display changes.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | No. 1 Engine Room Relay Block
(ST No. 1 Relay Installation Terminal) |
Remove the ST NO. 1 relay.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST NO. 1 relay installation terminal 5 - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST NO. 1 relay.
Inspect the ST NO. 1 relay.
Click hereEngine / Hybrid System>M20A-FKS (STARTING)>RELAY>INSPECTION
| Proceed to |
|---|
| OK (w/ Stop and Start System) |
| OK (w/o Stop and Start System) |
| NG |
OK (w/ Stop and Start System)
OK (w/o Stop and Start System)
NG
Disconnect the C43 starter assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST NO. 1 relay installation terminal 3 - C43-2 (SL1) | Always | Below 1 Ω |
| ST NO. 1 relay installation terminal 3 or C43-2 (SL1) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Starter Assembly) |
Disconnect the starter assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D1-1 (B) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C42 starter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST NO. 1 relay installation terminal 3 - C42-1 (ST) | Always | Below 1 Ω |
| ST NO. 1 relay installation terminal 3 or C42-1 (ST) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Starter Assembly) |
Disconnect the starter assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D2-1 (B) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check that the steering unlocks when the engine switch is turned on (ACC).
The steering unlocks.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Get into the vehicle while carrying an electrical key transmitter sub-assembly.
Press the engine switch with the clutch pedal released and check that the security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).
The security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).
The immobiliser function can be determined to be operating correctly if the security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A24 ECM connector.
Enter the following menus: Body Electrical / Power Source Control / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Neutral SW/ Clutch SW | State of clutch pedal | ON or OFF | ON: Clutch pedal depressed
OFF: Clutch pedal released |
·
Use this item to determine whether the clutch position switch is malfunctioning. ·
The engine cannot be started when this item is "OFF". |
| Tester Display |
|---|
| Neutral SW/ Clutch SW |
The GTS display changes correctly in response to the clutch pedal operation.
| Proceed to |
|---|
| OK |
| NG (w/ Stop and Start System) |
| NG (w/o Stop and Start System) |
OK
for A25A-FKS:
Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>ECM>REMOVAL
for M20A-FKS:
Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>ECM>REMOVAL
NG (w/ Stop and Start System)
NG (w/o Stop and Start System)
Disconnect the A34 engine stop and start ECU connector.
Enter the following menus: Body Electrical / Power Source Control / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Neutral SW/ Clutch SW | State of clutch pedal | ON or OFF | ON: Clutch pedal depressed
OFF: Clutch pedal released |
·
Use this item to determine whether the clutch position switch is malfunctioning. ·
The engine cannot be started when this item is "OFF". |
| Tester Display |
|---|
| Neutral SW/ Clutch SW |
The GTS display changes correctly in response to the clutch pedal operation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the clutch start switch assembly.
for LHD:
Click hereDrivetrain>CLUTCH>CLUTCH START SWITCH (for LHD)>REMOVAL
for RHD:
Click hereDrivetrain>CLUTCH>CLUTCH START SWITCH (for RHD)>REMOVAL
Inspect the clutch start switch assembly.
for LHD:
Click hereDrivetrain>CLUTCH>CLUTCH START SWITCH (for LHD)>INSPECTION
for RHD:
Click hereDrivetrain>CLUTCH>CLUTCH START SWITCH (for RHD)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD:
Click hereDrivetrain>CLUTCH>CLUTCH START SWITCH (for LHD)>REMOVAL
for RHD:
Click hereDrivetrain>CLUTCH>CLUTCH START SWITCH (for RHD)>REMOVAL
Disconnect the A15 certification ECU (smart key ECU assembly) connector.
Remove the ST NO. 1 relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A15-9 (STAR) - A81-2 | Always | Below 1 Ω |
| A15-20 (STA) - A81-1 | Always | Below 1 Ω |
| A15-9 (STAR) or A81-2 - Other terminals and body ground | Always | 10 kΩ or higher |
| A15-20 (STA) or A81-1 - Other terminals and body ground | Always | 10 kΩ or higher |
Connect the A15 certification ECU (smart key ECU assembly) connector.
Connect the A81 clutch start switch assembly connector.
Install the ST NO. 1 relay
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Certification ECU (Smart Key ECU Assembly)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A15-9 (STAR) - Body ground | Engine switch pressed and held with clutch pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off) | 6 V or higher* → 1 V or less |
*: While the engine is cranking, the battery voltage may drop to approximately 6 V.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST NO. 1 relay.
Inspect the ST NO. 1 relay.
Click hereEngine / Hybrid System>M20A-FKS (STARTING)>RELAY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | No. 1 Engine Room Relay Block
(ST No. 1 Relay Installation Terminal) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST NO. 1 relay installation terminal 2 - Body ground | Engine switch pressed and held with clutch pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off) | 6 V or higher* → 1 V or less |
*: While the engine is cranking, the battery voltage may drop to approximately 6 V.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | No. 1 Engine Room Relay Block
(ST No. 1 Relay Installation Terminal) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST NO. 1 relay installation terminal 1 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Get into the vehicle while carrying an electrical key transmitter sub-assembly.
Move the shift state park (P).
With the brake pedal released, check that pressing the engine switch causes the power source mode to change.
| Result | Proceed to |
|---|---|
| Power source mode changes: Off → on (ACC) → on (IG) → off | A |
| Power source mode does not change to on (ACC) or on (IG) | B |
| Power source mode changes to on (IG) but not to on (ACC) | C |
| Power source mode changes to on (ACC) but not to on (IG) | D |
A
B
C
D
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Power Source Control / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Stop Light Switch1 | State of brake pedal | OFF or ON | OFF: Brake pedal released
ON: Brake pedal depressed |
·
Use this item to determine if the stop light switch assembly is malfunctioning. ·
The engine cannot be started when this item is OFF. ·
If the stop light switch assembly is malfunctioning, the engine can be started by pressing and holding the engine switch for a certain period of time. |
| Tester Display |
|---|
| Stop Light Switch1 |
The GTS display changes correctly in response to the brake pedal operation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Enter the following menus: Body Electrical / Power Source Control / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Shift P Signal | State of brake pedal | ON or OFF | ON: Shift state park (P)
OFF: Shift state not park (P) |
·
Use this item to determine if the shift position switch is malfunctioning. ·
The engine cannot be started when this item is OFF. |
| Tester Display |
|---|
| Shift P Signal |
The GTS display changes correctly in response to the shift state.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Enter the following menus: Body Electrical / Power Source Control / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Neutral SW/ Clutch SW | Shift position (P, N) | ON or OFF | ON: Shift state park (P) or (N)
OFF: Shift state not park (P) or (N) |
·
Use this item to determine whether the park/neutral position switch assembly is malfunctioning. ·
When the engine cannot be started due to a park/neutral position switch assembly malfunction, OFF is displayed. |
| Tester Display |
|---|
| Neutral SW/ Clutch SW |
Enter the following menus: Body Electrical / Starting Control / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Shift Position P or N | Park/Neutral position switch status | OFF or ON | OFF: Shift state not park (P) or (N)
ON: Shift state park (P) or (N) |
When OFF is displayed, the engine will not crank. |
| Tester Display |
|---|
| Shift Position P or N |
The GTS display changes correctly in response to the shift state.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Starter Request Signal | Engine start request signal status | OFF or ON | OFF: The engine switch is not pressed
ON: With the shift state park (P) and the brake pedal depressed, the engine switch is pressed and held |
·
When the engine cannot be started due to a start request signal malfunction, OFF is displayed. ·
When the engine switch is pressed, the duration of time that ON is displayed will be extremely short. As such, the engine switch needs to be pressed and held for a certain period of time. |
| Tester Display |
|---|
| Starter Request Signal |
Check that the key indicator display is displayed on the multi-information display in the combination meter assembly, and then press the engine switch.
The GTS display changes correctly in response to the engine switch operation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Get into the vehicle while carrying an electrical key transmitter sub-assembly.
Shift state park (P).
Enter the following menus: Body Electrical / Starting Control / Data List.
Read the Data List while pressing the engine switch with the brake pedal depressed according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Starter SW | Starter operation request | OFF or ON | OFF: Starter operation not requested
ON: Starter operation requested |
When OFF is displayed, the engine will not crank. |
| Tester Display |
|---|
| Starter SW |
The GTS display changes.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | No. 1 Engine Room Relay Block
(ST No. 1 Relay Installation Terminal) |
Remove the ST NO. 1 relay.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST NO. 1 relay installation terminal 5 - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST NO. 1 relay.
Inspect the ST NO. 1 relay.
for A25A-FKS:
Click hereEngine / Hybrid System>A25A-FKS (STARTING)>RELAY>INSPECTION
for M20A-FKS:
Click hereEngine / Hybrid System>M20A-FKS (STARTING)>RELAY>INSPECTION
| Proceed to |
|---|
| OK (w/ Stop and Start System) |
| OK (w/o Stop and Start System) |
| NG |
OK (w/ Stop and Start System)
OK (w/o Stop and Start System)
NG
Disconnect the C43 starter assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST NO. 1 relay installation terminal 3 - C43-2 (SL1) | Always | Below 1 Ω |
| ST NO. 1 relay installation terminal 3 or C43-2 (SL1) - Other terminals and body ground | Always | 10 kΩ or higher |
Connect the C43 starter assembly connectors.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | No. 2 Engine Room Relay Block
(ST No. 2 Relay Installation Terminal) |
Remove the ST NO. 2 relay.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST NO. 2 relay installation terminal 2 - Body ground | Engine switch pressed and held with brake pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off) | 6 V or higher* → 1 V or less |
*: While the engine is cranking, the battery voltage may drop to approximately 6 V.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | No. 2 Engine Room Relay Block
(ST No. 2 Relay Installation Terminal) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST NO. 2 relay installation terminal 1 - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST NO. 2 relay installation terminal 5 - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST NO. 2 relay.
Inspect the ST NO. 2 relay.
Click hereEngine / Hybrid System>M20A-FKS (STARTING)>RELAY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C43 starter assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST NO. 2 relay installation terminal 3 - C43-1 (SL2) | Always | Below 1 Ω |
| ST NO. 2 relay installation terminal 3 or C43-1 (SL2) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Starter Assembly) |
Disconnect the starter assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D1-1 (B) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
for A25A-FKS:
Click hereEngine / Hybrid System>A25A-FKS (STARTING)>STARTER (w/ Stop And Start System)>REMOVAL
for M20A-FKS:
NG
Disconnect the A34 engine stop and start ECU connector.
Disconnect the A24 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST NO. 2 relay installation terminal 2 - A34-23 (STA2) | Always | Below 1 Ω |
| ST NO. 2 relay installation terminal 2 - A24-30 (STA) | Always | Below 1 Ω |
| ST NO. 2 relay installation terminal 2 or A34-23 (STA2) - Other terminals and body ground | Always | 10 kΩ or higher |
| ST NO. 2 relay installation terminal 2 or A24-30 (STA) - Other terminals and body ground | Always | 10 kΩ or higher |
Connect the A34 engine stop and start ECU connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Install the ST NO. 2 relay.
| *a | Component without harness connected
(Engine Stop and Start ECU) |
- | - |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A34-23 (STA2) - Body ground | Engine switch pressed and held with brake pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off) | 6 V or higher* → 1 V or less |
*: While the engine is cranking, the battery voltage may drop to approximately 6 V.
| Proceed to |
|---|
| OK |
| NG |
OK
for A25A-FKS:
Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>ECM>REMOVAL
for M20A-FKS:
Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>ECM>REMOVAL
NG
Disconnect the C42 starter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST NO. 1 relay installation terminal 3 - C42-1 (ST) | Always | Below 1 Ω |
| ST NO. 1 relay installation terminal 3 or C42-1 (ST) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Starter Assembly) |
Disconnect the starter assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D2-1 (B) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
for A25A-FKS:
Click hereEngine / Hybrid System>A25A-FKS (STARTING)>STARTER (w/o Stop And Start System)>REMOVAL
for M20A-FKS:
Click hereEngine / Hybrid System>M20A-FKS (STARTING)>STARTER (for 1.2 kW Type)>REMOVAL
NG
Check that the steering unlocks when the engine switch is turned on (ACC).
The steering unlocks.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Get into the vehicle while carrying an electrical key transmitter sub-assembly.
Shift state park (P).
Press the engine switch with the brake pedal released and check that the security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).
The security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).
The immobiliser function can be determined to be operating correctly if the security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A24 ECM connector.
Enter the following menus: Body Electrical / Power Source Control / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Neutral SW/ Clutch SW | Shift position (P, N) | ON or OFF | ON: Shift state park (P) or (N)
OFF: Shift state not park (P) or (N) |
·
Use this item to determine whether the park/neutral position switch assembly is malfunctioning. ·
When the engine cannot be started due to a park/neutral position switch assembly malfunction, OFF is displayed. |
| Tester Display |
|---|
| Neutral SW/ Clutch SW |
Enter the following menus: Body Electrical / Starting Control / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Shift Position P or N | Park/Neutral position switch status | OFF or ON | OFF: Shift state not park (P) or (N)
ON: Shift state park (P) or (N) |
When OFF is displayed, the engine will not crank. |
| Tester Display |
|---|
| Shift Position P or N |
The GTS display changes correctly in response to the shift state.
| Proceed to |
|---|
| OK |
| NG (w/ Stop and Start System) |
| NG (w/o Stop and Start System) |
OK
for A25A-FKS:
Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>ECM>REMOVAL
for M20A-FKS:
Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>ECM>REMOVAL
NG (w/ Stop and Start System)
NG (w/o Stop and Start System)
Disconnect the A34 engine stop and start ECU connector.
Enter the following menus: Body Electrical / Power Source Control / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Neutral SW/ Clutch SW | Shift position (P, N) | ON or OFF | ON: Shift state park (P) or (N)
OFF: Shift state not park (P) or (N) |
·
Use this item to determine whether the park/neutral position switch assembly is malfunctioning. ·
When the engine cannot be started due to a park/neutral position switch assembly malfunction, OFF is displayed. |
| Tester Display |
|---|
| Neutral SW/ Clutch SW |
Enter the following menus: Body Electrical / Starting Control / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Shift Position P or N | Park/Neutral position switch status | OFF or ON | OFF: Shift state not park (P) or (N)
ON: Shift state park (P) or (N) |
When OFF is displayed, the engine will not crank. |
| Tester Display |
|---|
| Shift Position P or N |
The GTS display changes correctly in response to the shift state.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the park/neutral position switch assembly.
for 2WD:
Click hereDrivetrain>UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>REMOVAL
for 4WD:
Click hereDrivetrain>UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>REMOVAL
Inspect the park/neutral position switch assembly.
for 2WD:
Click hereDrivetrain>UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION
for 4WD:
Click hereDrivetrain>UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for 2WD:
Click hereDrivetrain>UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>REMOVAL
for 4WD:
Click hereDrivetrain>UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>REMOVAL
Disconnect the A15 certification ECU (smart key ECU assembly) connector.
Disconnect the C31 park/neutral position switch assembly connector.
Remove the ST NO. 1 relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A15-9 (STAR) - C31-4 (B) | Always | Below 1 Ω |
| A15-20 (STA) - C31-9 (L) | Always | Below 1 Ω |
| A15-9 (STAR) or C31-4 (B) - Other terminals and body ground | Always | 10 kΩ or higher |
| A15-20 (STA) or C31-9 (L) - Other terminals and body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A15-9 (STAR) - C31-4 (B) | Always | Below 1 Ω |
| A15-20 (STA) - C31-5 (L) | Always | Below 1 Ω |
| A15-9 (STAR) or C31-4 (B) - Other terminals and body ground | Always | 10 kΩ or higher |
| A15-20 (STA) or C31-5 (L) - Other terminals and body ground | Always | 10 kΩ or higher |
Connect the A15 certification ECU (smart key ECU assembly) connector.
Connect the C31 park/neutral position switch assembly connector.
Install the ST NO. 1 relay
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Certification ECU (Smart Key ECU Assembly)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A15-9 (STAR) - Body ground | Engine switch pressed and held with brake pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off) | 6 V or higher* → 1 V or less |
*: While the engine is cranking, the battery voltage may drop to approximately 6 V.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST NO. 1 relay.
Inspect the ST NO. 1 relay.
for A25A-FKS:
Click hereEngine / Hybrid System>A25A-FKS (STARTING)>RELAY>INSPECTION
for M20A-FKS:
Click hereEngine / Hybrid System>M20A-FKS (STARTING)>RELAY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | No. 1 Engine Room Relay Block
(ST No. 1 Relay Installation Terminal) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST NO. 1 relay installation terminal 2 - Body ground | Engine switch pressed and held with brake pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off) | 6 V or higher* → 1 V or less |
*: While the engine is cranking, the battery voltage may drop to approximately 6 V.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | No. 1 Engine Room Relay Block
(ST No. 1 Relay Installation Terminal) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST NO. 1 relay installation terminal 1 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Certification ECU (Smart Key ECU Assembly)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G54-22 (P) - Other terminals and body ground | Shift state park (P) → Shift state not park (P) | 9 V or higher → 2.76 V or less |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G54 certification ECU (smart key ECU assembly) connector.
Disconnect the G26 shift lock control unit assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G54-22 (P) - G26-3 (P2) | Always | Below 1 Ω |
| G54-22 (P) or G26-3 (P2) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Certification ECU (Smart Key ECU Assembly)) |
Reconnect the certification ECU (smart key ECU assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G54-22 (P) - Other terminals and body ground | Shift state park (P) | 9 V or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for 2WD:
Click hereDrivetrain>UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>SHIFT LEVER>REMOVAL
for 4WD:
Click hereDrivetrain>UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>SHIFT LEVER>REMOVAL
NG
| *a | Front view of wire harness connector
(to Stop Light Switch Assembly) |
Disconnect the stop light switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A40-7 (B) - Body ground | Always | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A40-2 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the stop light switch assembly.
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the M7 certification ECU (smart key ECU assembly) connector.
Disconnect the A24 ECM connector.
Disconnect the A39 skid control ECU assembly connector.
Disconnect the G26 shift lock control unit assembly connector.
Disconnect the C33 transmission control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M7-25 (STP1) - A40-3 (L) | Always | Below 1 Ω |
| M7-25 (STP1) or A40-3 (L) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG