Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM (for HV Model, with Entry and Start System)
RM3620E _58 Vehicle Interior _076046 DOOR LOCK _0370164 WIRELESS DOOR LOCK CONTROL SYSTEM(for HV Model, with Entry and Start System) U

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(for HV Model, with Entry and Start System)  TERMINALS OF ECU  


CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


E402359C15
3.458,7.698 3.854,8 0.396,0.302 5.458,3.292 5.875,3.531 0.417,0.24 3.167,3.323 3.583,3.563 0.417,0.24 1.125,3.313 1.542,3.552 0.417,0.24 1.833,4.583 2.25,4.823 0.417,0.24 1.01,6.198 1.427,6.438 0.417,0.24 3.615,6.198 4.031,6.438 0.417,0.24 5.333,4.594 5.75,4.833 0.417,0.24 6.25,6.271 6.667,6.51 0.417,0.24 5.26,6.365 5.677,6.604 0.417,0.24 1.594,1.177 1.833,1.177 true 1.135,2.948 0.927,2.948 0.927,2.948 0.927,2.333 true 1.573,0.615 1.573,0.396 1.573,0.396 1.74,0.396 true 1.594,1.51 1.833,1.51 true 1.594,1.823 1.833,1.823 true 3.719,0.948 3.875,1.146 0.156,0.198 10 false A 3.604,7.76 3.76,7.958 0.156,0.198 10 false A 0.833,1.042 1.146,1.24 0.313,0.198 10 false 4H 0.844,1.635 1.156,1.833 0.313,0.198 10 false 4F 0.844,2 1.156,2.198 0.313,0.198 10 false 4L 1.885,1.104 2.344,1.302 0.458,0.198 10 false G43 1.885,1.427 2.344,1.625 0.458,0.198 10 false G44 1.906,1.771 2.365,1.969 0.458,0.198 10 false G45 1.229,2.854 1.729,3.083 0.5,0.229 10 false 4K 1.792,0.344 2.25,0.542 0.458,0.198 10 false *1 5.813,1.073 6.125,1.271 0.313,0.198 10 false 4D 5.813,1.719 6.125,1.917 0.313,0.198 10 false 4A 1.177,3.354 1.635,3.552 0.458,0.198 10 false G45 3.219,3.375 3.677,3.573 0.458,0.198 10 false G44 5.531,3.333 5.99,3.531 0.458,0.198 10 false G43 1.927,4.625 2.24,4.823 0.313,0.198 10 false 4A 5.469,4.635 5.781,4.833 0.313,0.198 10 false 4D 1.167,6.25 1.479,6.448 0.313,0.198 10 false 4F 3.688,6.219 4,6.417 0.313,0.198 10 false 4H 6.375,6.323 6.688,6.521 0.313,0.198 10 false 4L 5.385,6.406 5.74,6.563 0.354,0.156 10 false 4K
*1 Main Body ECU (Multiplex Network Body ECU) - -


a.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

for LHD:Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL

for RHD:Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL


b.

Reconnect the instrument panel junction block assembly connectors.


c.

Measure the voltage and resistance according to the value(s) in the table below.

Tester Connection Wiring Color Input/Output Terminal Description Condition Specified Condition Related Data List Item
A-11 (GND1) - Body ground - - Ground Always Below 1 Ω -
A-30 (ACC) - Body ground - Input ACC power supply Power switch on (ACC) 11 to 14 V ACC SW
Power switch off Below 1 V
A-31 (BECU) - Body ground - Input Auxiliary battery power supply Power switch off 11 to 14 V -
A-32 (IG) - Body ground - Input IG power supply Power switch on (IG) 11 to 14 V IG SW
Power switch off Below 1 V


d.

Install the main body ECU (multiplex network body ECU) to the instrument panel junction block assembly.

for LHD:Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>INSTALLATION

for RHD:Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>INSTALLATION


e.

Measure the voltage and check for pulses according to the value(s) in the table below.

Tester Connection Wiring Color Input/Output Terminal Description Condition Specified Condition Related Data List Item
4F-29 (BZR) - Body ground L - Body ground Output Wireless door lock buzzer output Active Test Wireless Buzzer on Pulse generation
(frequency: 2 kHz, high voltage: 11 to 14 V, low voltage: below 1 V)
-
Active Test Wireless Buzzer off Below 1 V



CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


B427558E25
3.25,0.542 3.656,0.781 0.406,0.24 4.531,0.542 4.938,0.781 0.406,0.24 3.354,0.583 3.667,0.781 0.313,0.198 10 false M7 4.594,0.583 4.906,0.781 0.313,0.198 10 false G54

a.

Disconnect the G54 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Tester Connection Wiring Color Input/Output Terminal Description Condition Specified Condition Related Data List Item
G54-18 (E) - Body ground W-B - Body ground - Ground Always Below 1 Ω -
G54-4 (+B) - Body ground P - Body ground Input Power supply Power switch off 11 to 14 V -
G54-15 (CUTB) - Body ground V - Body ground Input Dark current cut pin* Power switch off 11 to 14 V -

*: In order to prevent the vehicle battery from being depleted when the vehicle is shipped long distances, a fuse that cuts unnecessary electrical load while the vehicle is being shipped is installed in the circuit. If the fuse is removed, the circuit becomes open. If the fuse that is between the vehicle battery and terminal CUTB is removed and the circuit is open, the certification ECU (smart key ECU assembly) changes to a certain control mode (example: the transmission of radio waves every 0.25 seconds, which form the detection area, stops).



c.

Reconnect the G54 certification ECU (smart key ECU assembly) connector.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Tester Connection Wiring Color Input/Output Terminal Description Condition Specified Condition Related Data List Item
G54-17 (IG1D) - G54-18 (E) L - W-B Output IG power supply Power switch off → on (IG) 1 V or less → 9 V or higher
Power Source Control

IG Relay Monitor (Outside)


G54-16 (ACCD) - G54-18 (E) G - W-B Output ACC power supply Power switch off → on (ACC) 1 V or less → 8.5 V or higher
Power Source Control

ACC Relay Monitor


M7-18 (RCO) - G54-18 (E) L - W-B Output Output to door control receiver
(Power supply for door control receiver. Certification ECU (smart key ECU assembly) outputs 5 V when receiver starts operating.)
Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

3.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed


Pulse generation
(See waveform 1)
-
M7-19 (RDAM) - G54-18 (E) G - W-B Input Door control receiver verifies data received from electrical key transmitter sub-assembly.
Door control receiver sends data from electrical key transmitter sub-assembly to certification ECU (smart key ECU assembly) (Door control receiver intermittently grounds 12 V signal from certification ECU (smart key ECU assembly)).
Proceed:
1.

Power switch off

2.

All doors locked

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

5.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed


Pulse generation
(See waveform 2)
-
M7-20 (CSEL) - G54-18 (E) BE - W-B Output Communication channel switching circuit Procedure:
1.

Power switch off

2.

All doors closed


Below 1 V → pulse generation -


e.
B251178C12
0.198,1 0.531,1.198 0.333,0.198 10 GND 1.01,1.885 1.198,2.042 0.188,0.156 10 *a 2.021,1.885 2.208,2.042 0.188,0.156 10 *b
*a Before lock or unlock switch of electrical key transmitter sub-assembly pressed
*b After lock or unlock switch of electrical key transmitter sub-assembly pressed


Using an oscilloscope, check waveform 1.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 1 (Reference)
Item Content
Tester Connection M7-18 (RCO) - G54-18 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition
Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

3.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed




f.
B251177C12
0.208,1 0.542,1.198 0.333,0.198 10 GND 1.021,1.896 1.208,2.052 0.188,0.156 10 *a 2.188,1.906 2.375,2.063 0.188,0.156 10 *b
*a Before lock or unlock switch of electrical key transmitter sub-assembly pressed
*b After lock or unlock switch of electrical key transmitter sub-assembly pressed


Using an oscilloscope, check waveform 2.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 2 (Reference)
Item Content
Tester Connection M7-19 (RDAM) - G54-18 (E)
Tool Setting 5 V/DIV., 500 ms/DIV.
Condition
Procedure:
1.

Power switch off

2.

All doors locked

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

5.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed