Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.
When installing the main body ECU (multiplex network body ECU), always replace it with a new one.
89221
1.INSTALL MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
Hold the main body ECU (multiplex network body ECU) with your dominant hand.
| *a | Connector |
Do not touch the connector.
Make sure foreign matter does not enter the terminals.
| *a | Fitting Surface |
Hold the instrument panel junction block assembly with your other hand.
Make sure there is no foreign matter in the fitting surface.
| *a | 20° or more |
|
Install in this Direction |
|
Housing Sidewall |
Set the guide of the main body ECU (multiplex network body ECU) against the housing sidewall.
Make sure the angle between the instrument panel junction block assembly and the main body ECU (multiplex network body ECU) is 20° or more.
|
Install in this Direction |
|
Housing Sidewall |
Slide the guide of the main body ECU (multiplex network body ECU) along the housing sidewall in the direction indicated by the arrow.
|
Install in this Direction |
|
Side A |
Slide it until it contacts side A.
|
Install in this Direction |
Contact side A.
Do not contact side A with the main body ECU (multiplex network body ECU) too hard.
| *a | Center of Rotation (Contacts Surface A) |
|
Rotate in this Direction |
| *a | Center of Rotation (Contacts Surface A) |
|
Rotate in this Direction |
While pressing the main body ECU (multiplex network body ECU) against side A (center of rotation) of the instrument panel junction block assembly, rotate it until it enters the lock of the instrument panel junction block assembly.
The center of rotation is the one that contacts surface A.
Rotate it until it enters the lock of the instrument panel junction block assembly.
| *a | Before Locking | *b | Main Body ECU (Multiplex Network Body ECU) Lock |
| *c | Instrument Panel Junction Block Assembly Lock | - | - |
|
Install in this Direction |
|
Pressing Area |
Press the pressing area of the main body ECU (multiplex network body ECU).
Press it in one of the following ways.
| *a | Press the 2 sides of the main body ECU (multiplex network body ECU) with both hands. | *b | Press the center of the main body ECU (multiplex network body ECU) with one hand. |
|
Place fingers or the palm of your hand here | - | - |
Do not hit on or put your weight on the main body ECU (multiplex network body ECU) when engaging the main body ECU (multiplex network body ECU).
Check the engagement of the main body ECU (multiplex network body ECU) and the instrument panel junction block assembly by the locking sound.
| *a | Back Side of Main Body ECU (Multiplex Network Body ECU) |
| *b | Rib Surrounding Instrument Panel Junction Block Assembly |
Check that the back side of the main body ECU (multiplex network body ECU) and the rib surrounding the instrument panel junction block assembly are the same height.
| *a | After Locking (Height Matches) | *b | Back Side of Main Body ECU (Multiplex Network Body ECU) |
| *c | Rib Surrounding Instrument Panel Junction Block Assembly | - | - |
|
Confirm Visually | - | - |
Attach the claw to install the junction block bracket to the instrument panel junction block assembly.
2.INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU (for HV Model)
Attach the wire harness clamp.
| *a | Lever Connector | - | - |
|
Rotate in this Direction | - | - |
Attach the claw to connect the 2 lever connectors.
Be sure to connect the connector securely.
Attach the claw to install the instrument panel junction block assembly with main body ECU to the connector holder.
Attach the wire harness clamp.
|
Nut |
|
Bolt |
Attach the claw to install the instrument panel junction block assembly with main body ECU with the nut and bolt.
Connect the 3 connectors.
Attach the wire harness clamp.
89981
3.INSTALL HYBRID VEHICLE CONTROL ECU ASSEMBLY (for HV Model)
4.INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU (for Gasoline Model)
Attach the wire harness clamp.
| *a | Lever Connector | - | - |
|
Rotate in this Direction | - | - |
Attach the claw to connect the 2 lever connectors.
Be sure to connect the connector securely.
Attach the claw to install the connector holder to the instrument panel junction block assembly with main body ECU.
Attach the wire harness clamp.
|
Nut |
|
Bolt |
Attach the claw to install the instrument panel junction block assembly with main body ECU with the nut and bolt.
w/ Stop and Start System:
Connect the 3 connectors.
Attach the wire harness clamp.
w/o Stop and Start System:
Connect the 5 connectors.
|
Rotate in this Direction |
Connect the 2 connectors.
Attach the wire harness clamp.
Attach the claw to connect the 2 lever connectors.
Be sure to connect the connector securely.
Attach the wire harness clamp.
Connect the 3 connectors.
89261A
5.INSTALL ENGINE STOP AND START ECU (for Gasoline Model, with Stop and Start System)
55433B
6.INSTALL LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL
55550
7.INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY
55607
8.INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
62112
9.INSTALL COWL SIDE TRIM BOARD LH
Use the same procedure described for the RH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>INSTALLATION
67914B
10.INSTALL FRONT DOOR SCUFF PLATE LH
58810J
11.INSTALL CONSOLE BOX ASSEMBLY
12.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
for A25A-FKS:
for M20A-FKS:
for A25A-FXS:
Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>INSTALLATION
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
65351A
13.INSTALL BATTERY HOLE COVER (for HV Model)
58416K
14.INSTALL REAR NO. 2 FLOOR BOARD (for HV Model)
58410B
15.INSTALL DECK BOARD ASSEMBLY (for HV Model)
16. PERFORM DIAGNOSTIC SYSTEM CHECK
for HV Model with Occupant Classification System:
for Gasoline Model with Occupant Classification System:
w/o Occupant Classification System:
17.CHECK SRS WARNING LIGHT
for HV Model with Occupant Classification System:
for Gasoline Model with Occupant Classification System:
w/o Occupant Classification System: