Home › Power Source / Network › POWER DISTRIBUTION › MAIN BODY ECU (for LHD) › 2018.10–2019.02
RM3620E _57 Power Source / Network _076180 POWER DISTRIBUTION _0371061 MAIN BODY ECU(for LHD) A

POWER DISTRIBUTION  MAIN BODY ECU(for LHD)  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

When installing the main body ECU (multiplex network body ECU), always replace it with a new one.



PROCEDURE

Hide 89221 1.INSTALL MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (except Manual Transaxle)

a.
E403062

Hold the main body ECU (multiplex network body ECU) with your dominant hand.

NOTICE:
E403063C01
1.896,1.906 1.896,1.26 true 1.833,1.938 2.146,2.094 0.313,0.156 10 false *a
*a Connector


·

Do not touch the connector.

·

Make sure foreign matter does not enter the terminals.




b.
E403064C01
2.229,0.896 2.438,1.063 0.208,0.167 10 true *a
*a Fitting Surface


Hold the instrument panel junction block assembly with your other hand.

NOTICE:

Make sure there is no foreign matter in the fitting surface.



c.
E403065C01
0.229,0.344 0.542,0.5 0.313,0.156 10 false *a
*a 20° or more
V113147

Install in this Direction
V100155

Housing Sidewall


Set the guide of the main body ECU (multiplex network body ECU) against the housing sidewall.

HINT:

Make sure the angle between the instrument panel junction block assembly and the main body ECU (multiplex network body ECU) is 20° or more.



d.
E403066C01
0,0 0,0 false
V113147

Install in this Direction
V100155

Housing Sidewall


Slide the guide of the main body ECU (multiplex network body ECU) along the housing sidewall in the direction indicated by the arrow.


e.
E403067C01
0,0 0,0 false
V113147

Install in this Direction
V100155

Side A


Slide it until it contacts side A.


f.
E403068C01
0,0 0,0 false
V113147

Install in this Direction


Contact side A.

NOTICE:

Do not contact side A with the main body ECU (multiplex network body ECU) too hard.



g.
E403069C01
2.708,1.677 2.708,1.177 false 2.625,1.719 2.938,1.875 0.313,0.156 10 false *a
*a Center of Rotation (Contacts Surface A)
V113147

Rotate in this Direction


E403070C01
2.563,1.969 2.563,1.365 true 2.5,1.979 2.813,2.135 0.313,0.156 10 false *a
*a Center of Rotation (Contacts Surface A)
V113147

Rotate in this Direction


While pressing the main body ECU (multiplex network body ECU) against side A (center of rotation) of the instrument panel junction block assembly, rotate it until it enters the lock of the instrument panel junction block assembly.

HINT:

The center of rotation is the one that contacts surface A.



h.

Rotate it until it enters the lock of the instrument panel junction block assembly.

E403071C01
3.823,2.094 4.333,1.635 true 4.448,1.5 4.823,1.156 true 1.813,0.583 2.125,0.74 0.313,0.156 10 false *a 4.781,1 4.99,1.156 0.208,0.156 10 true *b 3.625,2.083 3.938,2.24 0.313,0.156 10 false *c
*a Before Locking *b Main Body ECU (Multiplex Network Body ECU) Lock
*c Instrument Panel Junction Block Assembly Lock - -



i.
E403072C01
0,0 0,0 false
V113147

Install in this Direction
V100155

Pressing Area


Press the pressing area of the main body ECU (multiplex network body ECU).

NOTICE:
·

Press it in one of the following ways.

E403073C01
0.938,0.479 1.25,0.635 0.313,0.156 10 false *a 4.208,0.469 4.521,0.625 0.313,0.156 10 false *b
*a Press the 2 sides of the main body ECU (multiplex network body ECU) with both hands. *b Press the center of the main body ECU (multiplex network body ECU) with one hand.
V113146

Place fingers or the palm of your hand here - -


·

Do not hit on or put your weight on the main body ECU (multiplex network body ECU) when engaging the main body ECU (multiplex network body ECU).

·

Check the engagement of the main body ECU (multiplex network body ECU) and the instrument panel junction block assembly by the locking sound.




j.
E403074C01
0.813,1.792 0.813,1.125 true 1.76,1.594 0.813,1.594 true 1.531,0.833 1.74,1.021 0.208,0.188 10 true *a 0.74,1.844 1.052,2 0.313,0.156 10 false *b
*a Back Side of Main Body ECU (Multiplex Network Body ECU)
*b Rib Surrounding Instrument Panel Junction Block Assembly


Check that the back side of the main body ECU (multiplex network body ECU) and the rib surrounding the instrument panel junction block assembly are the same height.

E403075C01
5.156,1.115 5.146,0.573 5.146,0.573 5.573,0.573 false 4.427,1.104 4.417,0.563 4.417,0.563 4.719,0.563 false 1.635,0.667 1.948,0.823 0.313,0.156 10 false *a 5.635,0.5 5.948,0.656 0.313,0.156 10 false *b 4.771,0.49 5.083,0.646 0.313,0.156 10 false *c
*a After Locking (Height Matches) *b Back Side of Main Body ECU (Multiplex Network Body ECU)
*c Rib Surrounding Instrument Panel Junction Block Assembly - -
V113147

Confirm Visually - -



k.
E405822

Attach the claw to install the junction block bracket to the instrument panel junction block assembly.


Hide 2.INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU (except Manual Transaxle)

a.

Attach the wire harness clamp.

E405910C01
0.948,1.729 1.344,1.729 1.344,1.729 1.344,2.865 true 0.938,2.188 1.344,2.188 true 1.271,2.917 1.583,3.073 0.313,0.156 10 false *a
*a Lever Connector - -
V113147

Rotate in this Direction - -



b.

Attach the claw to connect the 2 lever connectors.

NOTICE:

Be sure to connect the connector securely.



c.
E405820

Attach the claw to install the instrument panel junction block assembly with main body ECU to the connector holder.


d.
E405819

Attach the claw to install the instrument panel junction block assembly with main body ECU with the 2 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.
E405818

Connect the 5 connectors.


f.
E405911C01
1.813,0.708 2.333,0.708 true 1.823,1.063 2.115,1.063 2.115,1.063 2.115,0.708 true 2.365,0.594 2.594,0.781 0.229,0.188 10 true *a
*a Lever Connector
V113147

Rotate in this Direction


Connect the 2 connectors.


g.

Attach the wire harness clamp.


h.

Attach the claw to connect the 2 lever connectors.

NOTICE:

Be sure to connect the connector securely.



i.
E405816C01
2.365,1.74 2.552,1.917 0.188,0.177 10 true *a
*a w/ Clearance Warning System


w/ Clearance Warning System:

i.

Connect the 5 connectors.



j.

w/o Clearance Warning System:

i.

Connect the 4 connectors.



k.

Attach the 2 wire harness clamps.


Hide 55308B 3.INSTALL NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY (except Manual Transaxle)

a.
E405815C01
0,0 0,0 false
V100135

Nut
V100136

Bolt


Install the No. 3 instrument panel to cowl brace sub-assembly with the nut and bolt.

Torque:
Nut : 10 N*m (102 kgf*cm, 7 ft.*lbf)
Bolt : 10 N*m (102 kgf*cm, 7 ft.*lbf)


b.
E405814

Attach the 2 wire harness clamps.


Hide 73900 4.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (except Manual Transaxle)

Hide 89221 5.INSTALL MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (for Manual Transaxle)

a.
E403062

Hold the main body ECU (multiplex network body ECU) with your dominant hand.

NOTICE:
E403063C01
1.896,1.906 1.896,1.26 true 1.833,1.938 2.146,2.094 0.313,0.156 10 false *a
*a Connector


·

Do not touch the connector.

·

Make sure foreign matter does not enter the terminals.




b.
E405599C02
2.125,0.917 2.333,1.083 0.208,0.167 10 true *a
*a Fitting Surface


Hold the instrument panel junction block assembly with your other hand.

NOTICE:

Make sure there is no foreign matter in the fitting surface.



c.
E405600C01
0.052,0.479 0.365,0.635 0.313,0.156 10 false *a
*a 20° or more
V113147

Install in this Direction
V100155

Housing Sidewall


Set the guide of the main body ECU (multiplex network body ECU) against the housing sidewall.

HINT:

Make sure the angle between the instrument panel junction block assembly and the main body ECU (multiplex network body ECU) is 20° or more.



d.
E405601C01
0,0 0,0 false
V113147

Install in this Direction
V100155

Housing Sidewall


Slide the guide of the main body ECU (multiplex network body ECU) along the housing sidewall in the direction indicated by the arrow.


e.
E405602C01
0,0 0,0 false
V113147

Install in this Direction
V100155

Side A


Slide it until it contacts side A.


f.
E405603C01
0,0 0,0 false
V113147

Install in this Direction


Contact side A.

NOTICE:

Do not contact side A with the main body ECU (multiplex network body ECU) too hard.



g.
E405604C01
2.708,1.677 2.708,1.177 false 2.625,1.719 2.938,1.875 0.313,0.156 10 false *a
*a Center of Rotation (Contacts Surface A)
V113147

Rotate in this Direction


E405605C01
2.052,1.885 2.052,1.25 true 1.979,1.927 2.292,2.083 0.313,0.156 10 false *a
*a Center of Rotation (Contacts Surface A)
V113147

Rotate in this Direction


While pressing the main body ECU (multiplex network body ECU) against side A (center of rotation) of the instrument panel junction block assembly, rotate it until it enters the lock of the instrument panel junction block assembly.

HINT:

The center of rotation is the one that contacts surface A.



h.

Rotate it until it enters the lock of the instrument panel junction block assembly.

E405606C01
3.823,2.094 4.333,1.635 true 4.469,1.49 4.844,1.146 true 1.813,0.583 2.125,0.74 0.313,0.156 10 false *a 4.833,1 5.042,1.156 0.208,0.156 10 true *b 3.625,2.083 3.938,2.24 0.313,0.156 10 false *c
*a Before Locking *b Main Body ECU (Multiplex Network Body ECU) Lock
*c Instrument Panel Junction Block Assembly Lock - -



i.
E405607C01
0,0 0,0 false
V113147

Install in this Direction
V100155

Pressing Area


Press the pressing area of the main body ECU (multiplex network body ECU).

NOTICE:
·

Press it in one of the following ways.

E405608C01
0.938,0.479 1.25,0.635 0.313,0.156 10 false *a 4.208,0.469 4.521,0.625 0.313,0.156 10 false *b
*a Press the 2 sides of the main body ECU (multiplex network body ECU) with both hands. *b Press the center of the main body ECU (multiplex network body ECU) with one hand.
V113146

Place fingers or the palm of your hand here - -


·

Do not hit on or put your weight on the main body ECU (multiplex network body ECU) when engaging the main body ECU (multiplex network body ECU).

·

Check the engagement of the main body ECU (multiplex network body ECU) and the instrument panel junction block assembly by the locking sound.




j.
E405609C01
0.781,1.781 0.781,1.115 true 1.698,1.573 0.781,1.573 true 1.448,0.927 1.656,1.115 0.208,0.188 10 true *a 0.729,1.833 1.042,1.99 0.313,0.156 10 false *b
*a Back Side of Main Body ECU (Multiplex Network Body ECU)
*b Rib Surrounding Instrument Panel Junction Block Assembly


Check that the back side of the main body ECU (multiplex network body ECU) and the rib surrounding the instrument panel junction block assembly are the same height.

E405610C01
4.635,1.115 4.625,0.573 4.625,0.573 5.052,0.573 false 3.833,1.104 3.823,0.563 3.823,0.563 4.125,0.563 false 1.125,0.667 1.438,0.823 0.313,0.156 10 false *a 5.125,0.5 5.438,0.656 0.313,0.156 10 false *b 4.188,0.49 4.5,0.646 0.313,0.156 10 false *c
*a After Locking (Height Matches) *b Back Side of Main Body ECU (Multiplex Network Body ECU)
*c Rib Surrounding Instrument Panel Junction Block Assembly - -
V113147

Confirm Visually - -



Hide 6.INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU (for Manual Transaxle)

a.
E407018C01
0,0 0,0 false
V113147

Rotate in this Direction


Attach the claw to connect the 2 lever connectors.

NOTICE:

Be sure to connect the connector securely.



b.
E405572

Attach the 2 wire harness clamps.


c.
E405918C01
0,0 0,0 false
V100135

Nut
V100136

Bolt


Attach the claw to install the instrument panel junction block assembly with main body ECU with the bolt and nut.

Torque:
Nut : 8.0 N*m (82 kgf*cm, 71 in.*lbf)
Bolt : 8.0 N*m (82 kgf*cm, 71 in.*lbf)


d.
E405575C01
0,0 0,0 false
V100135

Nut
V100136

Bolt


Install the ECU integration box RH with the nut and bolt.

Torque:
Nut : 5.5 N*m (56 kgf*cm, 49 in.*lbf)
Bolt : 5.5 N*m (56 kgf*cm, 49 in.*lbf)


e.
E405917

Connect the 3 connectors.


f.
E405919C01
0.865,0.719 1.479,0.719 true 1.177,0.719 1.177,1.198 1.177,1.198 1.49,1.198 true 0.615,0.635 0.833,0.813 0.219,0.177 10 true *a
*a Lever Connector
V113147

Rotate in this Direction


Connect the 2 connectors.


g.

Attach the claw to connect the 2 lever connectors.

NOTICE:

Be sure to connect the connector securely.



h.
E405597

Attach the 2 wire harness clamps.


i.

Connect the connector.


Hide 55433B 7.INSTALL LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL (for Manual Transaxle)

Hide 55550 8.INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY (for Manual Transaxle)

Hide 55607 9.INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for Manual Transaxle)

Hide 62111C 10.INSTALL COWL SIDE TRIM BOARD RH (for Manual Transaxle)

Hide 67913B 11.INSTALL FRONT DOOR SCUFF PLATE RH (for Manual Transaxle)

HINT:

Use the same procedure described for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION


Hide 58810J 12.INSTALL CONSOLE BOX ASSEMBLY (for Manual Transaxle)

Hide 13.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 65351A 14.INSTALL BATTERY HOLE COVER (for HV Model)

Hide 58416K 15.INSTALL REAR NO. 2 FLOOR BOARD (for HV Model)

Hide 58410B 16.INSTALL DECK BOARD ASSEMBLY (for HV Model)