CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
| *A | for LHD without Manual Transaxle, RHD | *B | for LHD with Manual Transaxle |
| *1 | Main Body ECU (Multiplex Network Body ECU) | - | - |
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Connect the instrument panel junction block assembly connectors.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
|
*1: except Manual Transaxle with Stop and Start System *2: for Manual Transaxle with Stop and Start System |
||||
| A-32 (IG) - Body ground | None - Body ground | Ignition power supply | Ignition switch ON | 11 to 14 V*1
10.5 to 16 V*2 |
| Ignition switch off | Below 1 V | |||
| A-31 (BECU) - Body ground | None - Body ground | Auxiliary battery power supply | Ignition switch off | 11 to 14 V |
| A-30 (ACC) - Body ground | None - Body ground | ACC power supply | Ignition switch ACC | 11 to 14 V |
| Ignition switch off | Below 1 V | |||
| A-11 (GND1) - Body ground | None - Body ground | Ground | Always | Below 1 Ω |
Install the main body ECU (multiplex network body ECU).
Check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| 4H-25 - Body ground | W - Body ground | LIN communication line | Ignition switch ON | Pulse generation |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| 4N-25 - Body ground | BE - Body ground | LIN communication line | Ignition switch ON | Pulse generation |
CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
| *A | for LHD |
| *B | for RHD |
Disconnect the J2*1 or I2*2 multiplex network master switch assembly connector.
*1: for LHD
*2: for RHD
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| J2-11 (B) - Body ground | B - Body ground | Battery power supply | Ignition switch off | 11 to 14 V |
| J2-12 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| I2-11 (B) - Body ground | B - Body ground | Battery power supply | Ignition switch off | 11 to 14 V |
| I2-12 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Measure the pulse according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| J2-17 (LIN1) - Body ground | GR - Body ground | LIN communication line | Ignition switch ON | Pulse generation |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| I2-17 (LIN1) - Body ground | GR - Body ground | LIN communication line | Ignition switch ON | Pulse generation |
CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
Disconnect the J6 front power window regulator motor assembly LH connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| J6-2 (B) - Body ground | B - Body ground | Battery power supply | Ignition switch off | 11 to 14 V |
| J6-1 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Measure the pulse according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| J6-9 (LIN) - Body ground | BE - Body ground | LIN communication line | Ignition switch ON | Pulse generation |
CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
Disconnect the I7 front power window regulator motor assembly RH connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| I7-2 (B) - Body ground | B - Body ground | Battery power supply | Ignition switch off | 11 to 14 V |
| I7-1 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Measure the pulse according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| I7-9 (LIN) - Body ground | BE - Body ground | LIN communication line | Ignition switch ON | Pulse generation |
CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
Disconnect the L5 rear power window regulator motor assembly LH connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| L5-2 (B) - Body ground | B - Body ground | Battery power supply | Ignition switch off | 11 to 14 V |
| L5-1 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Measure the pulse according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| L5-9 (LIN) - Body ground | BE - Body ground | LIN communication line | Ignition switch ON | Pulse generation |
CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
Disconnect the K5 rear power window regulator motor assembly RH connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| K5-2 (B) - Body ground | B - Body ground | Battery power supply | Ignition switch off | 11 to 14 V |
| K5-1 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Measure the pulse according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| K5-9 (LIN) - Body ground | BE - Body ground | LIN communication line | Ignition switch ON | Pulse generation |
CHECK SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (w/ Sliding Roof System)
Disconnect the P4 sliding roof drive gear sub-assembly connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| P4-1 (B) - Body ground | B - Body ground | Battery power supply | Ignition switch off | 11 to 14 V |
| P4-2 (E) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Measure the pulse according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| P4-7 (MPX1) - Body ground | P - Body ground | LIN communication line | Ignition switch ON | Pulse generation |
CHECK SLIDING ROOF DRIVE GEAR ASSEMBLY (w/ Panoramic Moon Roof System)
Disconnect the P4 sliding roof drive gear assembly connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| P4-1 (B) - Body ground | W - Body ground | Battery power supply | Ignition switch off | 11 to 14 V |
| P4-2 (E) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Measure the pulse according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| P4-7 (MPX1) - Body ground | P - Body ground | LIN communication line | Ignition switch ON | Pulse generation |
CHECK DOUBLE LOCK DOOR RELAY ASSEMBLY (w/Double Locking System)
Disconnect the A28 double lock door control relay assembly connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A28-11 (CPUB) - Body ground | LA-GR - Body ground | Battery power supply | Ignition switch off | 11 to 14 V |
| A28 -12 (+B) - Body ground | P - Body ground | Battery power supply | Ignition switch off | 11 to 14 V |
| A28-7 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Measure the pulse according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A28-9 (MPX1) - Body ground | LA-R - Body ground | LIN communication line | Ignition switch ON | Pulse generation |
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Entry and Start System)
| *A | for Gasoline Model | *B | for HV Model |
Disconnect the G54 certification ECU (smart key ECU assembly) connector.
Measure the voltage and resistance according to the value(s) in the table below.
Measure the values on the wire harness side with the connector disconnected.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G54-4 (+B) - Body ground | P - Body ground | Battery power supply | Ignition switch off | 11 to 14 V |
| G54-18 (E) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Reconnect the G54 certification ECU (smart key ECU assembly) connector.
Check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G54-13 (LIN) - Body ground | LG - Body ground | LIN communication line | Ignition switch ON | Pulse generation |
CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) (w/ Entry and Start System)
Disconnect the G56 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G56-7 (B) - Body ground | W - Body ground | Battery power supply | Ignition switch off | 11 to 14 V |
| G56-1 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Reconnect the G56 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
Check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G56-5 (LIN) - Body ground | B - Body ground | LIN communication line | Ignition switch ON | Pulse generation |
CHECK ID CODE BOX (IMMOBILISER CODE ECU) (w/ Entry and Start System)
Disconnect the G57 ID code box (immobiliser code ECU) connector.
Measure the voltage and resistance according to the value(s) in the table below.
Measure the values on the wire harness side with the connector disconnected.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
|
*1: for Gasoline Model *2: for HV Model |
||||
| G57-5 (GND) - Body ground | LA - Body ground | Ground | Always | Below 1 Ω |
| G57-1 (+B) - Body ground | LA-B - Body ground*1
LA-GR - Body ground*2 |
+B power supply | Ignition switch off | 11 to 14 V |
Reconnect the G57 ID code box (immobiliser code ECU) connector.
Check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G57-2 (LIN1) - Body ground | GR - Body ground | LIN communication line | Ignition switch ON | Pulse generation |