Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM3620E _58 Vehicle Interior _076050 LIGHTING (INT) _0371654 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  IG Signal Circuit  


DESCRIPTION

This circuit detects the ignition switch ON or off condition, and sends it to the main body ECU (multiplex network body ECU).

WIRING DIAGRAM

for Manual Transaxle with Stop and Start System:


E414709E01
5.5,1.844 5.656,2.042 0.156,0.198 10 false A 5.479,2 7.125,2.365 1.646,0.365 10 false Main Body ECU (Multiplex Network Body ECU) 0.104,0.958 1.188,1.333 1.083,0.375 10 false from Engine Stop and Start ECU 3.146,1.854 3.458,2.052 0.313,0.198 10 false 4A 3.156,2.01 4.781,2.385 1.625,0.375 10 false Instrument Panel Junction Block Assembly 5.615,0.844 5.927,1.042 0.313,0.198 10 false 32 2.292,0.833 2.604,1.031 0.313,0.198 10 false 15 5.927,1.104 6.24,1.302 0.313,0.198 10 false IG


except Manual Transaxle with Stop and Start System:


E409865E01
5.438,2.74 5.594,2.938 0.156,0.198 10 false A 5.667,0.833 5.979,1.031 0.313,0.198 10 false IG 5.698,2.01 6.313,2.281 0.615,0.271 10 false GND1 5.396,2.917 7.031,3.292 1.635,0.375 10 false Main Body ECU (Multiplex Network Body ECU) 3.448,2.75 5.063,3.125 1.615,0.375 10 false Instrument Panel Junction Block Assembly 5.417,0.604 5.729,0.802 0.313,0.198 10 false 32 5.385,1.896 5.698,2.094 0.313,0.198 10 false 11 2.292,0.719 2.583,0.938 0.292,0.219 10 false 4M 2.719,0.719 3.01,0.938 0.292,0.219 10 false 4K 4.115,0.875 5.948,1.073 1.833,0.198 10 false ECU-IG1 NO.4 3.406,1.698 4.635,1.896 1.229,0.198 10 false IG1 NO.1 0.344,0.688 3.708,0.885 3.365,0.198 10 false from Auxiliary Battery 2.365,0.5 2.521,0.698 0.156,0.198 10 false 1 2.76,0.51 2.917,0.708 0.156,0.198 10 false 1 2.323,0.927 2.615,1.146 0.292,0.219 10 false *3 2.75,0.938 3.042,1.156 0.292,0.219 10 false *4 2.719,1.406 3.01,1.625 0.292,0.219 10 false 4A 2.729,2.021 3.021,2.24 0.292,0.219 10 false 4D 2.74,1.198 3.052,1.396 0.313,0.198 10 false 17 2.771,1.792 2.927,1.99 0.156,0.198 10 false 3 0.281,1.26 1.667,1.958 1.385,0.698 10 false from Certification ECU (Smart Key ECU Assembly)*1 or Ignition Switch*2 0.083,2.75 3.448,2.948 3.365,0.198 10 false *1: w/ Entry and Start System 0.083,2.99 3.448,3.188 3.365,0.198 10 false *2: w/o Entry and Start System 0.094,3.479 3.458,3.677 3.365,0.198 10 false *4: except LHD, Manual Transaxle 0.094,3.229 3.458,3.427 3.365,0.198 10 false *3: for LHD, Manual Transaxle


CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

w/ Entry and Start System:

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/ Entry and Start System A
w/o Entry and Start System B



A

2.CHECK FOR DTC (ENTRY AND START SYSTEM [for Start Function])

B

3.READ VALUE USING GTS
2.CHECK FOR DTC (ENTRY AND START SYSTEM [for Start Function])
a.

Check for DTCs.


Body Electrical > Power Source Control > Trouble Codes
50001 223
OK:

Entry and start system (for Start Function) DTCs are not output.



Result:
Result Proceed to
OK A
NG (for HV Model) B
NG (for Gasoline Model) C



A

3.READ VALUE USING GTS

B

C

3.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
IG SW Ignition switch ON signal OFF or ON OFF: Ignition switch off
ON: Ignition switch ON
"OFF" is also displayed for this item when the ignition switch is ACC.
Body Electrical > Main Body > Data List
Tester Display
IG SW
50003 123 30
OK:

Normal conditions listed above are displayed.



Result:
Result Proceed to
OK A
NG (except Manual Transaxle with Stop and Start System) B
NG (for Manual Transaxle with Stop and Start System) C



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

4.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BATTERY AND BODY GROUND)

C

6.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BATTERY)
4.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BATTERY AND BODY GROUND)
a.

Disconnect the instrument panel junction block assembly connectors.

E409866C01
2.01,0.188 2.406,0.427 0.396,0.24 1.042,1.969 1.438,2.208 0.396,0.24 3.521,1.99 3.917,2.229 0.396,0.24 5.083,0.156 5.479,0.396 0.396,0.24 0.063,0.052 0.375,0.25 0.313,0.198 10 false *a 2.135,0.24 2.448,0.438 0.313,0.198 10 false 4A 1.156,2 1.469,2.198 0.313,0.198 10 false 4K 3.625,2.042 3.938,2.24 0.313,0.198 10 false 4M 1.531,2 1.844,2.198 0.313,0.198 10 false *B 3.979,2.01 4.292,2.208 0.313,0.198 10 false *A 5.188,0.198 5.5,0.396 0.313,0.198 10 false 4D
*A for LHD, Manual Transaxle *B except LHD, Manual Transaxle
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)
- -



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD, Manual Transaxle
Tester Connection Switch Condition Specified Condition
4M-1 - Body ground Ignition switch off 11 to 14 V
4A-17 - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V

except LHD, Manual Transaxle
Tester Connection Switch Condition Specified Condition
4K-1 - Body ground Ignition switch off 11 to 14 V
4A-17 - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4D-3 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.


E409872C01
1.771,0.229 2.25,0.438 0.479,0.208 5.188,0.25 5.667,0.458 0.479,0.208 2.479,1.823 2.958,2.031 0.479,0.208 6.104,1.708 6.583,1.917 0.479,0.208 6.104,2.083 6.583,2.292 0.479,0.208 1.635,2.021 1.823,2.021 1.823,2.021 2.156,2.385 true 4.365,2.385 4.656,2.052 4.656,2.052 4.833,2.052 true 5.354,0.271 5.667,0.469 0.313,0.198 10 false 4D 1.938,0.24 2.25,0.438 0.313,0.198 10 false 4A 2.635,1.833 2.948,2.031 0.313,0.198 10 false A 4.896,1.969 5.385,2.188 0.49,0.219 10 false IG 1.24,1.938 1.729,2.156 0.49,0.219 10 false GND1 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 6.26,1.729 6.573,1.927 0.313,0.198 10 false 4M 6.25,2.104 6.563,2.302 0.313,0.198 10 false 4K 6.688,1.719 7,1.917 0.313,0.198 10 false *A 6.688,2.063 7,2.26 0.313,0.198 10 false *B
*A for LHD, Manual Transaxle *B except LHD, Manual Transaxle
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD, Manual Transaxle
Tester Connection Condition Specified Condition
A-32 (IG) - 4M-1 Auxiliary battery not connected to 4A-17 and 4D-3 10 kΩ or higher
Auxiliary battery positive (+) → 4A-17
Auxiliary battery negative (-) → 4D-3
Below 1 Ω
A-11 (GND1) - 4D-3 Always Below 1 Ω

except LHD, Manual Transaxle
Tester Connection Condition Specified Condition
A-32 (IG) - 4K-1 Auxiliary battery not connected to 4A-17 and 4D-3 10 kΩ or higher
Auxiliary battery positive (+) → 4A-17
Auxiliary battery negative (-) → 4D-3
Below 1 Ω
A-11 (GND1) - 4D-3 Always Below 1 Ω



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG (for LHD) C
NG (for RHD) D



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

D

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BATTERY)
a.
E414710C01
1.49,0.219 1.875,0.5 0.385,0.281 0.063,0.094 0.375,0.292 0.313,0.198 10 false *a 1.615,0.281 1.927,0.479 0.313,0.198 10 false 4A
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Disconnect the instrument panel junction block assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
4A-15 - Body ground Ignition switch ON 10.5 to 16 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

7.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.


E414711C01
1.396,0.146 1.802,0.448 0.406,0.302 4.833,0.323 5.24,0.583 0.406,0.26 6.698,0.948 6.5,0.51 6.5,0.51 6.354,0.51 true 0.063,0.042 0.375,0.24 0.313,0.198 10 false *a 1.521,0.208 1.833,0.406 0.313,0.198 10 false 4A 5,0.375 5.156,0.573 0.156,0.198 10 false A 6.177,0.427 6.49,0.625 0.313,0.198 10 false IG
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-32 (IG) - 4A-15 Always Below 1 Ω



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG (for LHD) C
NG (for RHD) D



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

D

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY