Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM3620E _58 Vehicle Interior _076050 LIGHTING (INT) _0371654 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Interior Light Auto Cut Circuit  


DESCRIPTION

When the battery saving control operates, the main body ECU (multiplex network body ECU) controls the operation of the DOME CUT relay that is built into the instrument panel junction block assembly to turn off the interior lights.

WIRING DIAGRAM

E413939E01
5.74,2.708 6.354,2.906 0.615,0.198 10 false DOMR 5.417,2.719 5.729,2.917 0.313,0.198 10 false 23 2.927,1.604 3.24,1.802 0.313,0.198 10 false 4D 2.906,0.844 3.219,1.042 0.313,0.198 10 false 4H 3.646,2.542 4.26,2.74 0.615,0.198 10 false DOME 4.656,3.125 5.677,3.365 1.021,0.24 10 false DOME CUT 2.479,2.365 2.792,2.563 0.313,0.198 10 false 4M 2.927,2.365 3.24,2.563 0.313,0.198 10 false 4K 2.531,2.177 2.688,2.375 0.156,0.198 10 false 1 2.948,2.177 3.104,2.375 0.156,0.198 10 false 1 2.51,2.583 2.823,2.781 0.313,0.198 10 false *1 2.917,2.573 3.229,2.771 0.313,0.198 10 false *2 5.438,3.656 5.594,3.854 0.156,0.198 10 false A 5.427,3.844 7.083,4.229 1.656,0.385 10 false Main Body ECU (Multiplex Network Body ECU) 3.573,3.646 5.188,4.021 1.615,0.375 10 false Instrument Panel Junction Block Assembly 0.125,4.313 4.563,4.51 4.438,0.198 10 false *2: except LHD, Manual Transaxle 0.135,4.01 4.573,4.208 4.438,0.198 10 false *1: for LHD, Manual Transaxle 0.573,2.354 3.938,2.552 3.365,0.198 10 false from Auxiliary Battery 0.583,0.833 3.948,1.031 3.365,0.198 10 false to Each Interior Light 0.594,1.594 3.958,1.792 3.365,0.198 10 false to Each Interior Light 2.917,1.385 3.229,1.583 0.313,0.198 10 false 10 2.927,0.625 3.24,0.823 0.313,0.198 10 false 19 2.521,0.833 2.833,1.031 0.313,0.198 10 false 4N 2.521,1.042 2.833,1.24 0.313,0.198 10 false *1 2.917,1.052 3.229,1.25 0.313,0.198 10 false *2 2.51,0.635 2.823,0.833 0.313,0.198 10 false 19

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

w/ Entry and Start System:

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Perform the Active Test according to the display on the GTS.

Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Relay for Interior Light Auto Cut Function DOME CUT relay ON or OFF When performing this Active Test, turn all the interior lights on.
·

OFF: DOME CUT relay on (interior lights turn on)

·

ON: DOME CUT relay off (interior lights turn off)


Body Electrical > Main Body > Active Test
Tester Display
Relay for Interior Light Auto Cut Function
50004 123 66
OK:

All of the interior lights turn off when ON is selected.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BATTERY)
2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BATTERY)
a.
E409882C01
0.188,0.74 0.594,1.031 0.406,0.292 0.188,2.531 0.594,2.823 0.406,0.292 0.698,2.583 1.01,2.74 0.313,0.156 10 false *A 0.667,0.802 0.979,0.958 0.313,0.156 10 false *B 0.083,0.083 0.396,0.24 0.313,0.156 10 false *a 0.302,0.802 0.615,1 0.313,0.198 10 false 4K 0.292,2.615 0.604,2.813 0.313,0.198 10 false 4M
*A for LHD, Manual Transaxle
*B except LHD, Manual Transaxle
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Disconnect the instrument panel junction block assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD, Manual Transaxle
Tester Connection Switch Condition Specified Condition
4M-1 - Body ground Ignition switch off 11 to 14 V

except LHD, Manual Transaxle
Tester Connection Switch Condition Specified Condition
4K-1 - Body ground Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.


E361207C08
1.885,0.156 2.427,0.385 0.542,0.229 4.75,0.083 5.292,0.313 0.542,0.229 3.25,1.698 3.792,1.927 0.542,0.229 4.74,0.344 5.281,0.573 0.542,0.229 4.25,2.188 4.573,1.802 4.573,1.802 4.719,1.802 true 0.135,0.063 0.448,0.219 0.313,0.156 10 false *a 4.927,0.125 5.208,0.354 0.281,0.229 10 false 4K 2.073,0.177 2.354,0.406 0.281,0.229 10 false 4D 3.469,1.719 3.75,1.948 0.281,0.229 10 false A 4.781,1.688 5.24,1.885 0.458,0.198 10 false DOMR 4.938,0.375 5.219,0.604 0.281,0.229 10 false 4M 5.375,0.104 5.656,0.333 0.281,0.229 10 false *A 5.385,0.344 5.667,0.573 0.281,0.229 10 false *B
*A except LHD, Manual Transaxle *B for LHD, Manual Transaxle
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD, Manual Transaxle
Tester Connection Condition Specified Condition
4M-1 - 4D-10 Auxiliary battery not connected to 4M-1 and A-23 (DOMR) 10 kΩ or higher

except LHD, Manual Transaxle
Tester Connection Condition Specified Condition
4K-1 - 4D-10 Auxiliary battery not connected to 4K-1 and A-23 (DOMR) 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD, Manual Transaxle
Tester Connection Condition Specified Condition
4D-10 - Auxiliary battery negative (-) terminal Auxiliary battery positive (+) → 4M-1
Auxiliary battery negative (-) → A-23 (DOMR)
11 to 14 V
Auxiliary battery not connected to 4M-1 and A-23 (DOMR) Below 1 V

except LHD, Manual Transaxle
Tester Connection Condition Specified Condition
4D-10 - Auxiliary battery negative (-) terminal Auxiliary battery positive (+) → 4K-1
Auxiliary battery negative (-) → A-23 (DOMR)
11 to 14 V
Auxiliary battery not connected to 4M-1 and A-23 (DOMR) Below 1 V



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG (for LHD) C
NG (for RHD) D



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

D

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY