The main body ECU (multiplex network body ECU) detects the condition of the back door lock with courtesy light switch assembly (back door courtesy light switch).
w/ Power Back Door System:
w/o Power Back Door System:
w/ Entry and Start System:
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.
Read the Data List according to the display on the GTS.
Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Back Door Courtesy SW | Back door courtesy light switch signal | OFF or ON | OFF: Back door closed
ON: Back door open |
- |
| Tester Display |
|---|
| Back Door Courtesy SW |
Normal conditions listed above are displayed.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the back door lock with courtesy light switch assembly.
Inspect the back door lock with courtesy light switch assembly.
Click hereVehicle Interior>DOOR LOCK>BACK DOOR LOCK>INSPECTION
| Result | Proceed to |
|---|---|
| OK (w/ Power Back Door System) | A |
| OK (w/o Power Back Door System) | B |
| NG | C |
A
B
C
Disconnect the R14 back door lock with courtesy light switch assembly connector.
Disconnect the 4N*1 or 4H*2 instrument panel junction block assembly connector.
*1: for LHD, Manual Transaxle
*2: except LHD, Manual Transaxle
Disconnect the R18 multiplex network door ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R14-4 (CTY) - 4N-34 | Always | Below 1 Ω |
| R14-4 (CTY) or 4N-34 - Body ground | Always | 10 kΩ or higher |
| R14-1 (E) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R14-4 (CTY) - 4H-34 | Always | Below 1 Ω |
| R14-4 (CTY) or 4H-34 - Body ground | Always | 10 kΩ or higher |
| R14-1 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
| *A | for LHD, Manual Transaxle | *B | except LHD, Manual Transaxle |
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4N-34 - A-4 (BCTY) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4H-34 - A-4 (BCTY) | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG (for LHD) | C |
| NG (for RHD) | D |
A
B
C
D
Disconnect the R11 back door lock with courtesy light switch assembly connector.
Disconnect the 4N*1 or 4H*2 instrument panel junction block assembly connector.
*1: for LHD, Manual Transaxle
*2: except LHD, Manual Transaxle
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R11-3 (D+) - 4N-34 | Always | Below 1 Ω |
| R11-3 (D+) or 4N-34 - Body ground | Always | 10 kΩ or higher |
| R11-2 (ACT-) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R11-3 (D+) - 4H-34 | Always | Below 1 Ω |
| R11-3 (D+) or 4H-34 - Body ground | Always | 10 kΩ or higher |
| R11-2 (ACT-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
| *A | for LHD, Manual Transaxle | *B | except LHD, Manual Transaxle |
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4N-34 - A-4 (BCTY) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4H-34 - A-4 (BCTY) | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG (for LHD) | C |
| NG (for RHD) | D |
A
B
C
D