Home › Engine / Hybrid System › M20A-FKS (LUBRICATION) › OIL PUMP › 2018.10–2020.08
RM3620E _51 Engine / Hybrid System _076385 M20A-FKS LUBRICATION _0371898 OIL PUMP A

M20A-FKS LUBRICATION  OIL PUMP  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during oil pump removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

*2: w/ Gasoline Particulate Filter

Battery terminal is disconnected/reconnected Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system (Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*1
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration DTC P063051 is output (Click here)
ECU communication ID registration Engine start function See Service Bulletin for the registration method.
for M20A-FKS:

GPF Deposition Values*2

-

GPF deposition values save

-

GPF deposition values write



·

MIL comes on

·

Deterioration of fuel efficiency


(Click here)
for K120:
·

Perform reset memory

·

Perform road test to allow TCM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


(Click here)
for K120F:
·

Perform reset memory

·

Perform road test to allow TCM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


(Click here)
·

Replacement of engine assembly

·

Gas leak from exhaust system is repaired

·

Replacement of throttle body with motor assembly

·

Replacement of cam timing control motor with EDU assembly

·

Removal and installation of a cam timing control motor with EDU assembly

·

Replacement of camshaft timing gear assembly

·

Removal and installation of a camshaft timing gear assembly

·

Replacement of cylinder head sub-assembly

·

Replacement of camshaft (for intake or exhaust camshaft)

·

Replacement of camshaft timing exhaust gear assembly

·

Replacement of port fuel injector assembly

·

Replacement of direct fuel injector assembly

·

Replacement of fuel pump assembly (for high pressure side)

·

Replacement of engine coolant temperature sensor

·

Replacement of spark plug

·

Replacement of ignition coil assembly

·

Replacement of EGR valve assembly

·

Replacement of knock control sensor

·

Replacement of air fuel ratio sensor (sensor 2)


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of continuously variable transaxle assembly Air bleed oil pump with motor assembly Stop and start system (Click here)
·

Input transaxle compensation code into TCM

·

Perform reset memory

·

Deceleration sensor zero point calibration

·

CVT oil pressure calibration

·

Perform road test to allow TCM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


for Initialization:(Click here)
for Registration:(Click here)
Suspension, tires, etc.
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (for Gasoline model) (Click here)
Television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic view monitor system (for Gasoline model) (Click here)
Front wheel alignment adjustment
1.

Perform reset memory

2.

Perform acceleration sensor zero point calibration and store system information memorization.


·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)
Front bumper assembly (Including removal and installation)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (for Gasoline model) (Click here)
Front television camera view adjustment Panoramic view monitor system (for Gasoline model) (Click here)

NOTICE:
·

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.

·

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



PROCEDURE

Hide 11310 1.REMOVE TIMING CHAIN COVER ASSEMBLY

Hide 15104 3.REMOVE OIL STRAINER SUB-ASSEMBLY

Hide 89491 4.REMOVE ENGINE OIL LEVEL SENSOR

Hide 13620B 5.REMOVE ENGINE BALANCER ASSEMBLY

Hide 15100 6.REMOVE OIL PUMP ASSEMBLY

a.
A432708

Remove the 3 bolts and oil pump assembly from the stiffening crankcase assembly.