Home › Suspension › REAR SUSPENSION › REAR STABILIZER BAR › 2018.10–2019.02
RM3620E _53 Suspension _076491 REAR SUSPENSION _0372238 REAR STABILIZER BAR A

REAR SUSPENSION  REAR STABILIZER BAR  INSTALLATION  


PROCEDURE

Hide 48818 1.INSTALL REAR STABILIZER BUSHING

a.
C403440C01
0.948,0.75 1.031,0.583 1.031,0.583 1.281,0.583 false 0.802,0.896 0.885,1.229 0.885,1.229 1.052,1.229 true 2.875,1.146 2.792,0.979 2.792,0.979 2.542,0.979 false 2.948,1.333 2.865,1.667 2.865,1.667 2.698,1.667 true 1.094,1.177 1.427,1.51 0.333,0.333 10 false *b 1.323,0.531 1.74,0.781 0.417,0.25 10 false *a 2.375,0.906 2.792,1.156 0.417,0.25 10 false *a 2.531,1.604 2.865,1.938 0.333,0.333 10 false *b
*a Stopper
*b Cutout


Install the 2 rear stabilizer bushings to the outside of the stoppers on the rear stabilizer bar.

NOTICE:

Be sure to install the rear stabilizer bushings so that each cutout faces the front of the vehicle.


HINT:

The cutout of the rear stabilizer bushing can be positioned either up or down.



Hide 48832A 2.INSTALL REAR NO. 1 STABILIZER BAR BRACKET LH

a.
C403441C01
2.427,4.031 2.667,3.896 2.667,3.896 2.833,3.896 true 2.75,0.625 2.667,0.542 2.667,0.542 2.417,0.542 false 2.875,3.844 3.125,4.094 0.25,0.25 10 false *a 2.25,0.479 2.583,0.729 0.333,0.25 10 false *b
*a Arrow Mark
*b Identification Mark
V100135

Upper of the Vehicle


Install the rear No. 1 stabilizer bar bracket LH to the rear stabilizer bushing.

NOTICE:
·

Ensure that the identification mark faces the right side of the vehicle.

·

Be sure to install the rear No. 1 stabilizer bar bracket LH so that each arrow mark faces the upper of the vehicle.




Hide 48832A 3.INSTALL REAR NO. 1 STABILIZER BAR BRACKET RH

HINT:

Perform the same procedure as for the LH side.


Hide 48835 4.INSTALL REAR LOWER STABILIZER BRACKET

a.
C403438

Install the 2 rear lower stabilizer brackets to the rear stabilizer bushing.


Hide 48812 5.INSTALL REAR STABILIZER BAR

a.
C403437C01
3.26,1.917 3.094,1 true 3.177,1.938 3.427,2.104 0.25,0.167 10 true *a 0.417,0.167 0.583,0.333 0.167,0.167 10 true A 2.917,0.167 3.083,0.333 0.167,0.167 10 true A 2.958,1.458 3.125,1.625 0.167,0.167 10 true B 0.438,1.458 0.604,1.625 0.167,0.167 10 true B
*a Identification Mark


Install the rear stabilizer bar, rear No. 1 stabilizer bar bracket LH, rear No. 1 stabilizer bar bracket RH, rear No. 2 stabilizer bar bracket LH, rear No. 2 stabilizer bar bracket RH and 2 rear stabilizer bushings to the rear suspension member sub-assembly with the 4 bolts.

Torque:
78 N*m (795 kgf*cm, 58 ft.*lbf)

NOTICE:
·

Ensure that the identification mark faces the right side of the vehicle.

·

Temporarily tighten the bolt (A) and then fully tighten the 2 bolts in the order of (B) and (A).




Hide 48840A 7.INSTALL REAR STABILIZER LINK ASSEMBLY LH

a.
C408080C01
1.333,2.958 1.667,3.208 0.333,0.25 10 false *a 1.271,0.094 1.458,0.281 0.188,0.188 10 true A 2.25,1.813 2.438,2 0.188,0.188 10 true B
*a Torque Wrench Fulcrum Length


Using a ball joint lock nut wrench, install the rear stabilizer link assembly LH with the nut (A).

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)

HINT:
·

If the ball joint turns together with the nut, use a 6 mm hexagon socket wrench to hold the stud bolt.

·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a ball joint lock nut wrench (fulcrum length of 159 mm (6.260 in.)) + torque wrench (fulcrum length of 400 mm (15.748 in.)):

71.6 N*m (730 kgf*cm, 53 ft.*lbf)




b.

Install the rear stabilizer link assembly LH with the bolt and nut (B).

Torque:
81 N*m (826 kgf*cm, 60 ft.*lbf)

NOTICE:

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.



Hide 48830D 8.INSTALL REAR STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48738C 9.INSTALL LOWER NO. 2 CONTROL ARM COVER LH (w/ Cover)

Hide 48737C 10.INSTALL LOWER NO. 2 CONTROL ARM COVER RH (w/ Cover)

HINT:

Perform the same procedure as for the LH side.


Hide 58399D 11.INSTALL NO. 2 FLOOR UNDER COVER (w/ Floor Under Cover)

Hide 58398F 12.INSTALL NO. 1 FLOOR UNDER COVER (w/ Floor Under Cover)

Hide 58166A 13.INSTALL FRONT FLOOR COVER LH (w/ Floor Under Cover)

Hide 58166A 14.INSTALL FRONT FLOOR COVER RH (w/ Floor Under Cover)

Hide 51420 15.INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY

Hide 53896B 17.INSTALL FRONT FENDER FRONT SPLASH SHIELD LH

Hide 53895B 18.INSTALL FRONT FENDER FRONT SPLASH SHIELD RH

Hide 58327B 19.INSTALL MAIN MUFFLER HEAT INSULATOR

a.

Install the main muffler heat insulator to the vehicle body with the 4 nuts.

Torque:
4.9 N*m (50 kgf*cm, 43 in.*lbf)


Hide 21.INSTALL REAR WHEEL